Acidic potassium dichromate solutions provide a traceable way to check UV-visible spectrophotometer absorbance accuracy at four selected wavelengths, with reported absorptivity uncertainties of ±0.7% near A=0.1 and ±0.2% near A=1 [S1].
The check covers 235, 257, 313 and 350 nm for absorbance scale accuracy and 345 nm for linearity over A=0.2–1, making it suitable for instrument qualification, periodic performance verification and pharmaceutical method control [S1].
What the Potassium Dichromate Check Measures
The procedure tests the instrument response rather than wavelength positioning. Five potassium dichromate concentrations in 0.001 M perchloric acid were characterized on a National Bureau of Standards high-accuracy spectrophotometer at eight UV wavelengths [S1]. The four wavelengths 235, 257, 313 and 350 nm correspond to absorbance maxima or minima in the hydrogen chromate and dichromate spectrum and are useful for checking narrow-bandpass spectrophotometers [S1].
At 345 nm, the absorptivity is sufficiently independent of concentration for absorbance-linearity checking to one part in one thousand over A=0.2–1 [S1]. This separates two related checks: selected-wavelength photometric accuracy at 235, 257, 313 and 350 nm, and concentration-response linearity at 345 nm.
Laboratory guidance published on 2026-03-18 links photometric accuracy to quantitative results through the Beer-Lambert relationship, in which absorbance is calculated from molar absorptivity, path length and concentration [S4]. A negative absorbance bias therefore propagates directly into concentration and purity results, including pharmaceutical potency calculations [S4].
Compare the Main Photometric Verification Options
Potassium dichromate is intended for UV absorbance accuracy and linearity, while neutral-density filters remain practical for the visible range. The choice should follow the wavelength and acceptance criterion rather than a single universal kit. [S1]
The alternatives are complementary, not interchangeable. A visible neutral-density set may cover four absorbance levels at five visible wavelengths [S5], whereas potassium dichromate supplies the wavelength-specific UV reference needed to diagnose an absorbance-scale error in the UV region [S1][S8].
Prepare the Solution and Test Sequence

Use a potassium dichromate reference material with certified values appropriate to the selected wavelengths and concentrations. Available reference formats include 20, 60 and 100 mg/L solutions plus a blank cell, specified for absorbance accuracy and linearity from 0–1 A over 235–350 nm [S7]. A pharmaceutical standards kit also specifies calibrated 60, 80 and 140 mg/L potassium dichromate solutions with a blank, providing UV absorbance accuracy to 2 A [S5].
Match the cell material and solution chemistry to the reference configuration. The foundational work used potassium dichromate in 0.001 M perchloric acid [S1], and commercial liquid-filter guidance likewise identifies potassium dichromate in perchloric acid as suitable for checking spectrophotometer photometric accuracy across 235–430 nm [S3]. Because the certified absorbance depends on concentration, acid matrix, wavelength, path length and reference procedure, a generic K2Cr2O7 concentration is not enough to set an acceptance value.
Measure the blank first, then read the certified solutions at their assigned wavelengths and temperatures. Compare measured absorbance with certified or accepted reference values, and calculate the deviation before judging the instrument. The July 2026 laboratory guide explicitly identifies potassium dichromate solution as the UV-range option for a photometric accuracy check [S8].
Read Accuracy, Linearity and Stray Light Separately
A good result at one absorbance value does not prove correct response across the operating range. The 2026 validation method treats photometric accuracy and stray light as separate performance characteristics, with each check addressing a different source of error in UV-visible measurements [S4].
For linearity, plot measured absorbance against the reference values over the selected concentration series. The 345 nm method provides a concentration-independent absorptivity and supports a one-part-in-one-thousand linearity assessment from A=0.2 to 1 [S1]. At 235, 257, 313 and 350 nm, the reported apparent absorptivities were reproducible to one part in one thousand, although small positive deviations from Beer’s law occurred because of partial HCrO4− dimerization to Cr2O7^2− [S1].
Do not treat stray-light failure as a concentration-calibration defect. Potassium dichromate supports the absorbance check, while the USP and EP separately call for stray-light performance verification [S5]. The complete pharmaceutical verification scope also includes wavelength accuracy, repeatability, absorbance accuracy, linearity, stray light and resolution, although not every test applies to every laboratory operation [S5].
Apply Controls for Traceable Interpretation

Control the variables that can turn a valid comparison into a false failure. The principal uncertainties in the foundational absorptivity values were ±0.7% at A=0.1 and ±0.2% near A=1, stated at the 95% confidence level for the mean and including known systematic-error sources [S1]. Those figures describe the reference characterization, not automatic pass limits for every instrument.
Use a wavelength-accuracy check before judging the dichromate result because an offset in wavelength changes the measured absorbance on a steep spectral slope. Holmium oxide solution covers 241–641 nm for wavelength-accuracy verification, while a mercury lamp can provide atomic emission lines for that purpose [S5]. A didymium glass filter is specified for 440, 465, 546.1, 590 and 635 nm in the visible standards set, and cerium solution is recommended for far-UV measurements [S5].
Control cell path length, solution temperature, baseline, reagent age and cleaning state, and document the reference-material identity, lot, cell specification and assigned absorbance values. For a regulated laboratory, the verification protocol should be tied to ISO 17025 or GLP evidence where applicable, while the instrument result is accepted only against a defined tolerance [S4].
Where the Check Fits in Laboratory Practice
Potassium dichromate is for laboratories that need an independent check of UV photometric accuracy, especially where absorbance feeds quantitative assays, concentration calculations or pharmaceutical compliance testing. It is also appropriate for comparing instruments and for investigating drift after lamp, detector, optical or cuvette-related work, provided the laboratory uses wavelength-appropriate reference material [S1][S8].
It is not a substitute for wavelength accuracy, stray-light, resolution or routine blank verification. It is also not the preferred primary check for instruments operating only in the visible range, where calibrated neutral-density filters provide four approximate absorbance levels at five visible wavelengths [S5]. A laboratory requiring a formal transfer standard across 200–350 nm must also account for the limits of the available reference materials and their certification history [S1].
The practical record to retain is specific: material identity and concentration, acid matrix, cell and path length, wavelength, blank result, measured absorbance, certified target, calculated deviation, repeatability, temperature, operator, instrument serial number and acceptance decision. That chain turns a dichromate reading into defensible evidence of UV photometric performance rather than a one-time instrument reading.