REQUEST FOR QUOTE → Request a quote
SpecForge Editorial Team

Two-Wire Pressure Transmitter Wiring for 4–20 mA Loops

Table of Contents
  1. Two-wire circuit configuration and current path
  2. Terminal-by-terminal wiring sequence
  3. Supply voltage and loop-resistance budget
  4. Pressure range, polarity and signal scaling
  5. Two-wire versus three-wire and four-wire arrangements
  6. Noise, grounding and shield termination
  7. Acceptance tests and failure diagnosis
Two-Wire Pressure Transmitter Wiring for 4–20 mA Loops

A two-wire 4–20 mA pressure transmitter combines DC power and measurement current on the same two conductors, normally with 12–30 VDC available at the transmitter terminals [S6][S9].

The complete circuit contains four functional elements: a DC power supply, the pressure transmitter, a receiver such as a PLC analog input, and field wiring [S3].

Two-wire circuit configuration and current path

The basic two-wire loop uses the same conductor pair to deliver power to the transmitter and return its 4–20 mA signal to the receiver, so no separate power or return conductor is required [S9]. Current originates at the DC supply, passes through the transmitter and field wiring, flows through the receiver input, and returns to the supply [S3].

At the calibrated lower range value, the transmitter drives 4 mA, while the upper range value corresponds to 20 mA [S2]. This live zero separates a genuine low-range measurement from an open circuit or loss of power, which normally appears as 0 mA [S2][S3].

Multiple receivers may be connected in series if the supply can support their combined voltage demand while remaining below the transmitter’s maximum allowable loop voltage [S3]. This makes the topology suitable for a local meter and a PLC or DCS input, provided the loop budget is recalculated rather than copied from the transmitter alone.

Terminal-by-terminal wiring sequence

Connect the supply positive or loop-plus conductor to the transmitter positive terminal, commonly marked L+ or V+, then connect the transmitter negative terminal, commonly marked L- or V-, to the positive input of the PLC analog module, AI+ [S5]. Connect the PLC analog-input negative terminal, AI-, to the supply negative or common, completing the series loop [S5].

Do not connect both transmitter leads directly across 24 VDC, because that shorts the regulated current output rather than operating the intended measurement loop [S3]. The pressure transmitter must control the current within the 4–20 mA range while extracting operating power from the same loop [S4].

A practical commissioning check is to record the current at the receiver, then compare it with the expected engineering value. The current measured by the PLC or meter should equal the current generated by the transmitter because the same current passes through the series loop [S3].

Supply voltage and loop-resistance budget

The supply must provide enough DC voltage for the transmitter, cable resistance, and every receiver in series, while staying inside each device’s minimum and maximum voltage ratings [S3]. One documented installation topology uses a 12–30 VDC pressure transmitter, a 24 VDC field supply and a panel meter with a 10 ohm input resistance [S6].

The transmitter’s internal electronics consume part of the available loop voltage, so the burden voltage is not the sum of cable resistance alone. The power supply, transmitter and receiver limits must be checked together because the transmitter extracts its operating power from the same conductors that carry the measurement signal [S4].

Wire resistance and total loop impedance matter most on long cable runs [S3]. The field calculation should include resistance per conductor over the actual route length, connection resistance and the input impedance of the PLC or meter. As an example, a 10 ohm input consumes about 0.10 V at 10 mA and 0.20 V at 20 mA by Ohm’s law, before transmitter burden and cable loss are added.

Pressure range, polarity and signal scaling

A transmitter diagram should map the selected mechanical range to the electrical range: 4 mA represents the lower calibrated pressure and 20 mA represents the upper calibrated pressure [S2]. This mapping must be confirmed in the transmitter configuration and the PLC input scaling, because correct wiring alone does not establish correct engineering units.

Polarity determines whether the transmitter can control the intended current path. If the supply positive is connected to the transmitter negative terminal, or the transmitter negative is connected incorrectly to the PLC input, the loop may read 0 mA or outside the expected 4–20 mA band [S5]. Confirm the terminal markings on the actual device rather than relying on a generic drawing, since some combinations of transmitter and input module use separate signal and supply terminals.

For testing and calibration, the process should be isolated from the pressure source and the transmitter exposed to a known low and high input. A loop calibrator can inject and measure loop current, while a loop tester can check continuity, open-circuit and short-circuit conditions before the process is restored.

Two-wire versus three-wire and four-wire arrangements

A two-wire transmitter is appropriate when one conductor pair can carry both power and signal, the available loop voltage is sufficient and only one 4–20 mA signal path is required [S8]. A three-wire arrangement provides separate power conductors with a shared common, while a four-wire arrangement separates power wiring from signal wiring entirely [S2][S5].

The pressure transmitter selection is therefore not only a pressure-range decision. Two-wire construction is the simplest physical installation, but it is the least flexible when the instrument needs additional power, separate signal grounding or multiple independent outputs.

Noise, grounding and shield termination

Current transmission reduces the effect of cable resistance and electrical noise over long industrial runs because the receiver measures current rather than a low-level voltage [S2][S3]. That advantage still depends on correct shielding, conductor routing and grounding, because poor installation can inject noise into the input or create an unintended ground path.

Shielding should be installed according to the field wiring instruction and instrument grounding arrangement, not by a generic assumption that every shield can be grounded at both ends without consequence [S5]. Keep the transmitter signal pair away from high-voltage power cables and motor feeders where practical. A voltage signal exposed to this environment can develop an error from conductor resistance and electromagnetic coupling, whereas the regulated 4–20 mA current remains defined through the series path [S5].

For a complete installation record, include the pressure range, 4 mA and 20 mA engineering values, supply voltage, measured loop current, cable route, shield termination and any added meter resistance. These records distinguish a sensor problem from an input-card, power-supply or wiring problem during later troubleshooting.

Acceptance tests and failure diagnosis

Before energizing the transmitter, confirm 12–30 VDC at a suitable installation point where that range is specified, check supply polarity, verify continuity through the complete series path and confirm that the PLC input is configured for 4–20 mA rather than 0–20 mA [S6]. A pressure calibrator or pressure source can then verify the lower and upper range points.

A reading of 0 mA points to an open loop, loss of supply or an incorrectly wired transmitter, because a powered two-wire transmitter at its zero condition should produce 4 mA rather than 0 mA [S2][S3]. A constant 20 mA may represent the upper range, a saturated transmitter or a wiring problem, so it must be checked against applied pressure rather than treated as a valid measurement automatically.

A receiver reading below 4 mA or above 20 mA requires checks of polarity, supply voltage, cable continuity, input-module configuration and transmitter setup. If the expected current appears at the transmitter but not at the PLC, the problem lies downstream in the wiring or analog input; if no current appears at either point, inspect the power supply and loop continuity first.

Track two signals after commissioning: the receiver current under a known low and high pressure condition, and the voltage available at the transmitter under load. Stable readings at both test points confirm the 4–20 mA current loop more reliably than a single display reading taken at one pressure.

Frequently asked questions

What supply voltage is normally available at the terminals of a two-wire 4–20 mA pressure transmitter?

A two-wire 4–20 mA pressure transmitter normally operates with 12–30 VDC available at its terminals. The same conductor pair carries both operating power and the measurement current.

How should a two-wire pressure transmitter be connected to a PLC analog input?

Connect supply positive or loop-plus to the transmitter positive terminal, commonly marked L+ or V+, and connect the transmitter negative terminal, commonly marked L- or V-, to PLC AI+. Connect PLC AI- to supply negative or common to complete the series loop.

How much loop voltage is consumed by a receiver with 10 ohms of input resistance?

A 10 ohm receiver consumes about 0.10 V at 10 mA and 0.20 V at 20 mA. The total supply-voltage calculation must also include transmitter burden, cable resistance, connection resistance, and any other series receivers.

How can a 4–20 mA pressure loop be checked for correct operation and engineering scaling?

Record the receiver current and compare it with the expected engineering value; the same current should flow through the series transmitter and receiver. Confirm that 4 mA maps to the lower calibrated pressure and 20 mA to the upper calibrated pressure in both transmitter configuration and PLC scaling.

9 sources
  1. Introduction to the Two-Wire Transmitter and the 4-20mA Current Loop
  2. 4-20 mA Transmitter Wiring: 2-Wire, 3-Wire & 4-Wire Guide (Jul 30, 2025)
  3. 4-20mA Current Loop Basics: Sensor Guide
  4. Designing 4mA to 20mA loop-powered transmitters
  5. Industrial Pressure Transmitter 4-20ma Wiring Topology - SimplyBuy
  6. Pressure Transducers |Installation and Wiring Diagrams
  7. How Two-Wire 4–20 mA Loop-Powered Current Sensors Work - Erqos (Oct 31, 2025)
  8. 4 - 20mA Transmitter Wiring Types: 2 -Wire, 3 - Wire & 4
  9. 4-20 mA Pressure Transmitter Wiring: Field Guide | WKSENSOR (Aug 18, 2026)

Need to source matching manufacturers or get a quote?

SpecForge connects industrial buyers with verified manufacturers. Submit your requirement and we will route it to matched suppliers.

Submit RFQ now →
Ask SpecForge AI