A 100:1 turndown ratio means a pressure transmitter can support a maximum span 100 times larger than its minimum span, subject to the sensing cell and stated accuracy.
The ratio describes measurement flexibility, not guaranteed accuracy: engineers must match the URL, calibrated span, pressure type, and process conditions before accepting the figure.
What a 100:1 Turndown Ratio Means
Instrument turndown is defined as the ratio of maximum allowable span to minimum allowable span for a particular instrument [S2]. On a transmitter with 100:1 capability, the largest permitted span is 100 times the smallest permitted span [S1][S2].
For example, if a transmitter accepts a maximum span of 1,000 psi, a 100:1 ratio permits a minimum span of 10 psi. The same model could therefore be configured for a 10 psi span or a 1,000 psi span, subject to its sensor capsule, electronics, zero settings, and stated accuracy [S1][S5].
Do not confuse the ratio with a tenfold reduction in output. The 4–20 mA output still maps the calibrated LRV to 4 mA and the calibrated URV to 20 mA. The wider capability allows the technician to select a different span without replacing the instrument [S1].
URL, URV, LRV, Span, and Turndown
Five range terms must be separated before a 100:1 claim can be interpreted: URL is the highest pressure the sensing cell can measure, LRL is its lowest permitted pressure, URV is the calibrated upper point, LRV is the calibrated lower point, and span equals URV minus LRV [S1][S5].
A 1,000 mbar URL with a 0–100 mbar calibrated range has a 100 mbar span and a 10:1 relationship when compared as URL divided by configured span. Reconfiguring the same cell to –300 to 0 mbar produces a 300 mbar span and a 3.33:1 relationship [S5].
These equations expose why a vendor can attach several turndown figures to one transmitter. Maximum span divided by minimum span describes instrument capability, while URL divided by configured span describes the selected application [S2][S5]. Accuracy at that setting still has to be confirmed from the model-specific documentation.
How 100:1 Compares with Lower Ratios
A lower ratio restricts re-ranging, a 100:1 ratio permits greater span flexibility, and a higher ratio adds more capability at the cost of tighter model-specific accuracy and zero constraints. Practical transmitter turndown figures commonly range from 10:1 to 100:1, depending on the model and manufacturer [S3].
A 10:1 transmitter with a 1,000 psi maximum span has a 100 psi minimum span. A 100:1 transmitter with the same maximum span can be narrowed to 10 psi [S1][S3]. The second device can cover more commissioning and operating ranges, but the headline ratio does not establish equal accuracy at both extremes.
Selection should therefore be judged by four criteria: minimum required span, maximum operating pressure, required accuracy at that span, and the need to move zero above, below, or across the operating pressure. A broad 100:1 range is useful only if the proposed calibration falls inside the permitted URL, LRL, and output electronics.
Where 100:1 Turndown Fits in Service
High turndown is useful on vessels whose operating pressure changes, startup conditions differ from steady-state conditions, or one transmitter type must support several test ranges. The pressure transmitter should be selected against the actual operating envelope rather than a generous ratio printed on a family datasheet. [S5]
For a 10–100 psi process, a transmitter capable of a 10 psi minimum span offers 100:1 capability if its maximum allowable span is 1,000 psi. If the maximum span is only 250 psi, the same 10 psi minimum gives 25:1, so the denominator must come from the transmitter data sheet [S2][S5].
This distinction matters in hydraulic, pneumatic, chemical, and energy applications. A 100:1 claim helps a maintainer avoid a special low-range sensor, but it does not remove checks for overpressure, static line pressure, temperature effects, diaphragm compatibility, and hazardous-area certification.
Accuracy, Zero, and Failure Traps
The lowest span is not automatically the most accurate span. Many transmitters are specified with a basic accuracy as a percentage of calibrated span, so the same percentage error becomes a smaller pressure error on a narrow range but can still affect control performance [S1]. A 0.10% error on a 10 psi span is 0.010 psi, while 0.10% on a 1,000 psi span is 1.0 psi.
Zero can impose a separate restriction. A transmitter may accept a positive LRV, a negative LRV, or a range crossing zero, depending on the model and sensor capsule. The configured span must also remain within the maximum allowable span; changing zero does not create unlimited range [S1][S5].
The three most common procurement errors are treating 100:1 as an accuracy statement, dividing by zero instead of minimum span, and comparing a family-level range with a model-specific capsule. Guard against those errors by requiring the URL, LRL, maximum span, minimum span, LRV, URV, and accuracy statement in the purchase specification.
Pressure Type Changes the Interpretation
The same numerical ratio can describe different hardware depending on pressure reference. An absolute pressure transmitter measures pressure referenced to vacuum, a gauge transmitter references atmosphere, and a differential pressure transmitter measures the difference between two inputs [S1].
For differential-pressure service, a low static-pressure model may have a restricted lower span even when its differential turndown is high. For example, the separate concepts of rangeability and static limit should be evaluated during procurement, as discussed in Pressure Transmitter Rangeability and Static Limit.
Absolute-pressure measurement also requires attention to the absolute zero and the LRV used for vacuum or near-vacuum service. Gauge-pressure rering can place the LRV below zero, but that is not equivalent to measuring sub-atmospheric absolute pressure. State the pressure type with every ratio to prevent a technically valid number from being applied to the wrong measurement.
What to Put in the RFQ
A 100:1 RFQ should request the maximum allowable span, minimum allowable span, URL, LRL, permitted LRV and URV, configured span, accuracy at that span, and pressure reference. It should also identify the process minimum, normal maximum, overpressure, static pressure, media, temperature, output signal, and hazardous-area requirements [S1][S5].
The arithmetic check is straightforward: maximum allowable span divided by minimum allowable span must equal 100:1. The engineering check is harder: the required span must be settable, and the quoted accuracy must apply at that span rather than only at the widest range [S2][S5].
For a fixed-ratio device, ask whether factory or field calibration is available and whether changing the span can affect certificate coverage, zero suppression, output mapping, and replacement-stock standardization. A broad ratio simplifies range planning, but it does not replace model-specific verification.
Turndown, Rangeability, and Selection Boundaries
Turndown is often used synonymously with rangeability, while stricter instrument definitions distinguish maximum allowable span from minimum allowable span [S1][S2]. Rangeability describes the transmitter’s usable breadth, while turndown in a purchasing context is often the ratio between the URL and the configured span [S5].
A 100:1 instrument is for applications that need a small minimum span, a broad maximum span, or later re-ranging. It is not sufficient evidence for a high-accuracy custody application, a high-overpressure service, or a hazardous installation. Accuracy class selection, environmental compensation, and certification must be evaluated separately, including the requirements covered in Selecting Pressure Transmitter Accuracy Class for Custody Transfer.
The decision point is trackable: calculate the proposed span, confirm that it equals or exceeds the model’s minimum allowable span, and verify the accuracy statement at that exact span. If the vendor supplies only “100:1” without URL, LRL, span limits, and accuracy conditions, the specification is incomplete.