REQUEST FOR QUOTE → Request a quote
SpecForge Editorial Team

CP Titanium Grade 1 vs Grade 4: Strength and Ductility

Table of Contents
  1. Strength and Ductility Trade-Off
  2. Decision Criteria: Formability, Load, and Service Life
  3. Where Grade 1 Fits
  4. Where Grade 4 Fits
  5. Limits, Failures, and Design Checks
  6. Specification and Procurement Checks
CP Titanium Grade 1 vs Grade 4: Strength and Ductility

CP titanium Grade 4 has a minimum yield strength of 480 MPa (70 ksi), and its yield strength is approximately 2.8 times that of Grade 1 [S3][S6].

The comparison applies to commercially pure titanium Grades 1 and 4, where increasing interstitial content raises strength while reducing ductility, formability, and impact tolerance [S2][S5].

Strength and Ductility Trade-Off

CP titanium Grade 1 is the softest commercially pure grade and has the highest ductility, good cold-forming characteristics, excellent weldability, and high impact toughness [S1][S2]. Grade 4 is the strongest CP grade, with a minimum yield strength of 480 MPa (70 ksi), while retaining good ductility and moderate formability [S3].

The trade-off is quantitative rather than nominal: Grade 1 has about 1.6 times the ductility of Grade 4, while Grade 4 has about 2.8 times the yield strength of Grade 1 [S6]. Published grade data also describes the ultimate tensile strength of Grade 4 as more than twice that of Grade 1 [S7].

This makes Grade 1 the preferred choice for deep forming, bending, expansion, or parts requiring substantial post-forming strain. Grade 4 is the better starting material when load capacity, corrosion-fatigue performance, or reduced section thickness controls the design. Both remain unalloyed CP titanium with the same basic corrosion mechanism [S1][S3].

Decision Criteria: Formability, Load, and Service Life

For fabrication effort, Grade 1 is the clear preference because its superior ductility and cold formability reduce the risk of cracking during severe forming. Grade 4 has lower ductility and moderate formability than the softer and more ductile Grade 1, while offering higher strength [S1][S3][S6].

For structural strength, Grade 4 is the strongest commercially pure grade, with a specified minimum yield strength of 480 MPa (70 ksi), and its strength can be dramatically increased by strain hardening [S3]. Grade 4 also offers strong resistance to corrosion fatigue, including marine exposure, making it useful for pressure equipment, reaction vessels, and airframe or engine components [S3].

For corrosion resistance, do not assume that Grade 4 is materially less resistant than Grade 1 merely because it is stronger. Grade 4 remains resistant to many oxidizing and alkaline media, organic compounds, acids, aqueous salts, and wet or dry hot gases; its passive oxide film reforms when oxygen or moisture is available [S3].

Where Grade 1 Fits

CP titanium grade 1 vs grade 4 strength and ductility - Where Grade 1 Fits
CP titanium grade 1 vs grade 4 strength and ductility - Where Grade 1 Fits

Grade 1 is suitable for architecture, desalination equipment, dimensional-stable anodes, medical products, marine components, chemical-processing equipment, and chlorate manufacturing [S2]. Typical forms include bar, plate, sheet, pipe, tube, strip, coil, forgings, and wire [S2].

Its mechanical profile is particularly useful where a component undergoes bending, deep drawing, spinning, flaring, or another forming operation after purchase.

In those cases, moving to Grade 4 may reduce material section or fabrication difficulty, provided the designer accepts lower ductility and more demanding forming practice [S1][S3].

Where Grade 4 Fits

Grade 4 is specified for chemical-processing machinery, reaction vessels, airframe and aircraft-engine components, dental and orthopedic implants, and other applications requiring the highest strength available within CP titanium [S3]. Its listed specifications include AMS 4901, AMS 4921, ASTM B265, ASTM B348, ASTM B367, ASTM B381, ASTM F67, ASTM F1341, ISO 5832-2, and MIL-T-9047, with associated designation UNS R50700 [S3].

The Grade 4 chemistry permits more interstitial impurities than the lower CP grades: the Carpenter Technology datasheet lists maxima of 0.50% iron, 0.40% oxygen, 0.08% carbon, 0.05% nitrogen, and 0.015% hydrogen [S3]. Those interstitial elements increase strength but reduce ductility, so the grade number is not a quality ranking or alloy designation; it identifies a chemistry and mechanical-property class [S2][S5].

Grade 4 also carries several operating constraints. The datasheet lists applicable service temperatures up to 204°C (400°F), although its seawater corrosion resistance extends to 315°C (600°F) [S3]. Crevice corrosion remains possible in tightly confined gaps, and susceptible environments include strongly reducing acids, alkaline peroxide solutions, and molten chloride salts [S3].

Limits, Failures, and Design Checks

CP titanium grade 1 vs grade 4 strength and ductility - Limits, Failures, and Design Checks
CP titanium grade 1 vs grade 4 strength and ductility - Limits, Failures, and Design Checks

Grade 4 has good ductility and only moderate formability, but its lower ductility than Grade 1 makes severe cold forming, tight-radius bending, and post-forming stretching less forgiving [S1][S3].

Corrosion design still requires environment-specific review. Grade 4’s continuous, tightly adherent oxide layer provides its broad resistance, and it reforms readily when air or moisture is present [S3]. Engineers must still identify reducing acids, peroxide-bearing alkalis, molten chlorides, and crevice geometries, and must not assume resistance to wet chlorine or bromine where the required oxygen or water is absent [S3].

For Grade 1, the primary limitation is strength. Its low strength can require a heavier section, greater wall thickness, or more fasteners to meet a given load [S1]. Neither grade should be specified by the word “titanium” alone: record the grade, product form, applicable material specification, dimensional standard, surface condition, heat treatment where relevant, and required mechanical test results.

Specification and Procurement Checks

Grade 1 procurement should identify the applicable product specification and form because sheet, plate, bar, tube, pipe, forging, and wire are not governed by one interchangeable purchase specification. Listed Grade 1 standards include ASME SB-363, ASME SB-381, ASME SB-337, ASME SB-338, ASME SB-348, ASME SB-265, ASTM F67, and ISO 5832-2 [S2].

Grade 4 procurement should likewise state the form and governing specification. Common specifications include ASTM B265 for sheet, strip, and plate; ASTM B348 for bar and billet; ASTM B367 for castings; ASTM B381 for forgings; ASTM F67 for sheet, strip, and bar; and AMS 4901 or AMS 4921 for specified aerospace forms [S3].

Do not compare only grade labels. Compare the same product form and condition, including cold-worked versus annealed material, because cold working can raise Grade 4 strength above 950 MPa [S3]. Also distinguish CP titanium from titanium alloys. In the wider titanium alloy family, Grade 5 Ti-6Al-4V is a different material class and should not be substituted for either CP grade without an explicit redesign [S1].

For a direct aerospace trade study, compare the titanium option with the composite alternative in Carbon Fiber vs Titanium for Aerospace Brackets. For CP titanium specifically, the practical selection rule remains simple: specify Grade 1 when formability and toughness dominate, specify Grade 4 when strength, corrosion fatigue, or section reduction dominate.

Frequently asked questions

What minimum yield strength should be specified for CP titanium Grade 4?

Specify a minimum yield strength of 480 MPa (70 ksi) for CP titanium Grade 4. Cold working can raise its strength above 950 MPa, while Grade 1 remains the softer and more ductile commercially pure grade.

Which CP titanium grade is better for deep drawing, tight-radius bending, and other severe forming?

Choose CP titanium Grade 1 for deep drawing, tight-radius bending, flaring, and other severe forming operations. It has about 1.6 times the ductility of Grade 4, along with better cold formability and a lower risk of cracking during substantial post-forming strain.

Can Grade 4 titanium reduce wall thickness compared with Grade 1 under the same design load?

Yes, because Grade 4 has about 2.8 times the yield strength of Grade 1 and more than twice its ultimate tensile strength [S6][S7].

What material specifications and product forms are listed for CP titanium Grade 4?

Listed Grade 4 specifications include AMS 4901, AMS 4921, ASTM B265, ASTM B348, ASTM B367, ASTM B381, ASTM F67, ASTM F1341, ISO 5832-2, and MIL-T-9047, with designation UNS R50700. Available forms include bar, plate, sheet, pipe, tube, strip, coil, forgings, and wire.

9 sources
  1. Understanding the Different Grades of Titanium (Apr 28, 2026)
  2. Titanium Grades & Specs | High-Performance ...
  3. CP Ti - GRADE 4
  4. Commercially pure titanium
  5. CP Titanium Grades 1–4 for Medical Devices (Oct 15, 2026)
  6. Grade-4 commercially pure titanium with ultrahigh strength ...
  7. Comparison between Titanium Grade 1, 2, 3 & 4 (Feb 28, 2024)
  8. Grade 2 vs. Grade 4 Titanium: Differences & Selection Guide (May 7, 2026)
  9. Getting The Lowdown On The Different Grades Of Titanium

Need to source matching manufacturers or get a quote?

SpecForge connects industrial buyers with verified manufacturers. Submit your requirement and we will route it to matched suppliers.

Submit RFQ now →
Ask SpecForge AI