The rubber conveyor belt price per metre for a 1,000 mm belt can be estimated by multiplying the rubber, fabric, and carcass factors to produce a ±5% range.
The choice is not simply belt versus belt: compare carcass strength, width, cover construction, belt length, splice method, delivery terms, installation cost, and replacement frequency before accepting a per-metre price.
What the EP400 and steel cord price comparison means
EP400 means a polyester fabric carcass with a nominal total tensile strength of 400 N/mm, while the suffix identifies the number of carcass plies, for example EP400/3. EP belts can contain 2–6 fabric plies, and commonly listed constructions include EP315/3, EP500/3, EP630/4, and EP800/4 [S4].
Steel cord conveyor belt uses steel tensile cords rather than woven fabric plies. One published production range covers ST500–ST5400, widths of 500–2,200 mm, minimum thickness of 12 mm, and minimum supplied length of 50 m [S5]. Sempertrans also lists textile and steel cord belts with belt widths up to 3,200 mm [S2].
Width, total carcass strength, cover rubber, belt length, splice, freight, taxes, and installation can move the final comparison substantially. Treat the meter price as one line in the installed-cost calculation, not as the purchase decision by itself.
Decision criteria: initial cost, capacity, distance, and service life
For lower-capacity, shorter-distance handling, fabric belts are described as the more cost-effective option [S6].
On operating envelope, EP construction is suitable for medium- and long-distance conveying at higher loads and speeds, while ultra-long-distance and extreme heavy-duty applications normally require steel cord [S4]. Steel cord is specified for long-distance, high-capacity, high-speed transport and offers high tensile strength, low elongation, impact resistance, and long belt life [S5].
A direct comparison is therefore:
Where EP400 gives the better business case

EP400 is the economical selection for shorter conveyors, moderate loads, and routes where steel cord construction is not required by the duty cycle. Typical EP applications include quarrying, ore, coke, aggregates, crops, sand, clinker, chemicals, and construction materials [S4].
Its polyester warp and polyamide weft construction provides low longitudinal elongation, resistance to moisture and mildew, flexible troughing, and a relatively short take-up requirement [S4]. These properties support stable tracking and predictable operation in ordinary bulk-handling installations, subject to the specified safety factor and operating conditions.
The economic case can be stronger than the purchase-price gap suggests. In a Fenner Dunlop case study, eight imported EP400/3 4+2 belts were replaced four times per year on two 8.65 m by 800 mm conveyors. The recorded annual costs were €9,200 for belt, €6,400 for fitting, and €64,000 for installation downtime, producing a stated total of €79,600 [S3].
That example is not proof of a universal EP400 life, but it demonstrates the calculation that matters: belt price multiplied by replacement frequency, plus labour and production-loss costs. The same case recorded 12–14 months of life for the selected Fenner Dunlop belt against 12–14 weeks for a competitor belt, with a stated annual saving of €59,890 [S3].
When steel cord earns its higher price
Steel cord is justified when the conveyor must combine long distance, high capacity, high speed, low elongation, and severe duty in one installation. Published construction options include general, rip-stop, impact, and special types, with covers available for abrasion, oil, cold, flame, chemical, impact, and ozone resistance [S5].
The construction has measurable engineering limits. For the cited steel cord belt, rubber-to-cord adhesion is specified at no less than 12 N/mm, with no steel-wire pull-out after 10,000 dynamic fatigue tests. Pull-out force before heating is at least 15d + 15 N/mm and after heating at least 15d + 5 N/mm, where d is the actual steel cord diameter in millimetres [S5].
The same specification gives width tolerance of ±1%, length tolerance from 0 to 2.5%, pitch tolerance of ±1.5 mm, cover thickness tolerance within -0.5 mm, and a maximum-to-minimum thickness spread below 10% [S5]. These tolerances matter because a lower catalogue price can be offset by variation, premature replacement, or installation problems.
Use steel cord when operating demand or replacement economics justify it. For short, lower-duty runs, paying the initial steel cord premium is difficult to defend. For long, high-capacity routes, a cheap EP belt that stretches, wears, or requires repeated shutdowns is not the low-cost solution.
Normalize every quotation before comparison

A valid per-metre comparison requires the same width, carcass strength, cover specification, length, and delivery basis. EP prices may be quoted per metre, per roll, or per tonne, with rolls commonly covering 200–300 m; these units are not interchangeable [S1].
Specify whether the quotation is bare belt ex-works, FOB port, or DDP so import duties, trimming, pallets, and freight are visible rather than embedded [S1]. Also state the required splice method, belt length tolerance, cover grade, delivery condition, and whether the quotation includes site installation.
For a practical request, ask for 1 m of installed belt cost as well as bare belt cost. The formula is straightforward: bare belt price per metre, plus splice and fitting per metre, plus expected downtime per metre, divided by expected service metres. Replace expected life with a defensible operating assumption rather than copying a catalogue claim.
Specify the carcass before accepting the lowest price
EP400/3 and an unspecified “EP belt” are not equivalent quotations. Record the total nominal strength as 400 N/mm, the number of plies as 3, belt width in millimetres, upper and lower cover thicknesses, cover compound, calculated length, and splice type. A worked notation such as EP1000/5 900*5 (6.5+3.0)=200 m demonstrates why the length unit and cover thicknesses must be explicit [S4].
For steel cord, request the ST grade, belt width, number and diameter of cords, carcass and cover construction, total belt thickness, rated working tension, minimum pulley diameter, splice details, and expected fatigue duty. The catalogue range of ST500–ST5400, 500–2,200 mm width, and minimum 12 mm thickness provides the initial screening envelope, not a complete design specification [S5].
The quoted price also needs a technical cross-check against belt safety factors, because carcass strength alone does not determine acceptable operating tension.
Final selection by application and installed cost

Choose EP400 when the conveyor has moderate capacity, does not require ultra-long-distance steel cord performance, and installation or replacement cost is a major part of ownership. Choose steel cord for long-distance, high-capacity, high-speed routes where low elongation, fatigue resistance, and reduced replacement frequency justify the premium [S4][S5].
For a short route or controlled project, request an EP400 quotation using the US$41–56/m reference band for a 1,000 mm belt and check it against the same width, cover, length, splice, and delivery terms [S1]. For a long heavy-duty route, price steel cord against expected service life, installation downtime, and the cost of frequent EP replacement rather than comparing catalogue meter prices alone.
Track three items in the quotation comparison: bare belt cost per metre, installed cost per metre, and planned replacement interval. If the steel cord option does not improve at least one of lifecycle cost, capacity, or operating performance for the specific conveyor, its roughly 30% initial price premium is not justified [S1].