Peroxide-cured EPDM generally provides lower compression set and greater high-temperature durability than sulfur-cured EPDM because carbon-carbon cross-links withstand thermal ageing better than sulfur-based bonds [S1][S3][S4].
Both cure systems apply to the same EPDM base polymer, but they produce different cross-link networks, cure kinetics, mechanical properties, and service windows; peroxide curing is normally preferred for sustained static compression, while sulfur curing is commonly specified for strength, dynamic fatigue, and cost [S1][S3].
Compression Set Comparison by Cure Chemistry
Compression set is the decisive property when an EPDM seal must retain contact pressure during continuous deflection. Peroxide-cured EPDM normally exhibits lower compression set because its carbon-carbon cross-link network supports long-term elastic recovery more effectively than the sulfur-linked network [S4][S6][S7].
This advantage becomes more valuable at elevated temperature and over extended service periods. Sulfur-cured EPDM can develop a higher permanent set, particularly when aged above approximately 125°C, while peroxide-cured EPDM is commonly described as suitable for continuous exposure around 150–160°C [S5]. A separate coatings comparison gives service limits of up to 150°C for peroxide-cured EPDM and 120°C for sulfur-cured EPDM [S2]. These figures are compound-specific limits rather than universal guarantees for every seal.
For a static gasket, O-ring, or spring-loaded seal, specify peroxide-cured EPDM when compression retention and thermal ageing outweigh the mechanical-strength gain from sulfur curing [S4][S5]. For dynamic or heavily stretched components, demand compression-set data at the actual temperature and deflection because compound formulation, filler loading, cross-link density, and cure state can alter the ranking [S1][S6].
Cross-Link Structure and Aging Behavior
Sulfur curing produces sulfidic cross-links, while peroxide curing produces carbon–carbon cross-links, and the type of curing system influences cross-link density and structure [S1][S3]. Peroxide curing follows a radical pathway in which organic peroxide cleavage generates radicals that form carbon-carbon links between EPDM chains [S1].
The C–C links have higher bond energy than sulfur linkages, so peroxide-cured EPDM retains physical properties more effectively during prolonged high-temperature exposure [S3][S4]. Sulfur-cured EPDM provides superior tensile strength and tear resistance, but conventional sulfur networks have weaker heat-ageing stability and lower resistance to thermo-oxidative ageing [S1][S3].
The curing system also changes processing. Sulfur systems require elemental sulfur, accelerators, and activators such as zinc oxide and stearic acid, while peroxide systems depend on organic peroxide decomposition temperature and cure kinetics [S1][S3]. A combined sulfur-peroxide formulation produced lower cross-link density than the corresponding single-system vulcanizates, yet achieved higher tensile strength and elongation at break than either single cure system in the tested filled and unfilled EPDM compounds [S1].
Decision Matrix for EPDM Seals

Compression set is not the only selection criterion: peroxide-cured EPDM offers lower compression set, excellent heat resistance, and stronger ageing resistance, while sulfur-cured EPDM offers better tensile strength, lower cost, and easier general-purpose availability [S4].
This comparison makes the trade-off explicit: peroxide curing buys compression-set retention and thermal endurance, while sulfur curing buys mechanical strength and lower cost. For an EPDM rubber procurement decision, do not compare the cures by elastomer name alone; require compression-set values, tensile and tear data, and ageing evidence for the specific compound [S1][S4].
Application Selection by Service Condition
Peroxide-cured EPDM is the stronger choice for hot-water, steam, automotive-cooling, HVAC, outdoor, and static sealing duties where the seal must maintain contact force for long periods [S4][S5]. The cited peroxide cure retains useful performance up to 150°C, compared with 120°C for sulfur cure in one coatings comparison [S2].
Sulfur-cured EPDM is the more practical choice for moderate-temperature water lines, weatherstripping, and general industrial static seals where mechanical durability and cost matter more than prolonged thermal ageing [S5]. It also performs well in dynamic applications because its longer sulfur linkages redistribute stress, while sulfur-cured vulcanizates generally outperform peroxide-cured versions in tensile strength and tear resistance [S3].
For chemical service, the cure chemistry still does not replace media compatibility testing. Material selection for industrial rubber applications should therefore include fluid-specific evidence rather than cure chemistry alone.
Specification and Test Requirements

Require the supplier to state the cure system, compound identity, and test conditions because the generic terms “peroxide-cured EPDM” and “sulfur-cured EPDM” do not define a complete material specification [S1][S4]. At minimum, request compression-set results at the design temperature and deflection, tensile strength, tear strength, and heat-ageing data [S3][S4].
Compression set must be compared on a common basis, including temperature, duration, deflection, and the method used to calculate permanent deformation. The research establishes the directional advantage of peroxide curing, but it does not provide one universal percentage across EPDM grades, filler systems, or test schedules [S4][S6].
Verify the operating-temperature claim against the supplier’s compound limit rather than transferring a generic 150°C or 160°C figure to a finished seal. Heat exposure, steam, fluid chemistry, and sustained compression can interact, and the service rating must cover the assembled product rather than an isolated material coupon [S2][S5].
Procurement Rules for Long-Term Sealing
Specify peroxide-cured EPDM for sustained static compression above moderate service temperatures, especially where leakage from loss of sealing force would force shutdown or rework [S4][S7]. Specify sulfur-cured EPDM for dynamic fatigue, high tensile or tear demand, and cost-sensitive service below the thermal-aging envelope where peroxide performance is not required [S3][S5].
Treat combined sulfur-peroxide curing as a development route rather than a default purchase specification. In the investigated EPDM formulations, the combined system produced higher tensile strength and elongation at break than the peroxide-only or sulfur-only equivalents, but it also had lower cross-link density [S1]. Confirm compression set and aged sealing performance on the finished geometry before accepting that route for a critical static seal.
The next procurement checkpoint is a like-for-like data sheet: one compound per cure system, identical test temperature and deflection, measured tensile and tear properties, and stated chemical and steam exposure limits. That comparison converts the general rule into an engineering choice and exposes gaps where a supplier’s compound data do not support the proposed service [S1][S4][S5].