REQUEST FOR QUOTE → Request a quote
SpecForge Editorial Team

Nickel Use in Alkaline Electrolyzers: 800 kg per MW

Table of Contents
  1. What the 800 kg-per-MW Benchmark Represents
  2. Why the Estimate Changes Between Electrolyzer Designs
  3. Stack Size and Hydrogen Output Are Separate Design Checks
  4. Alkaline and PEM Material Requirements Are Not Interchangeable
  5. Procurement Should Separate Gross and Recoverable Nickel
  6. Engineering and Commercial Limits on the Benchmark
Nickel Use in Alkaline Electrolyzers: 800 kg per MW

The British Geological Survey's electrolyser foresight study adopted 800 kilograms of nickel per megawatt as its reference alkaline-electrolyser material intensity [S6].

That figure is a planning benchmark rather than a universal physical constant, because electrode coatings, active-area loading, stack configuration, and the definition of installed MW can change total metal demand [S1][S2][S6].

What the 800 kg-per-MW Benchmark Represents

The 800 kg/MW value is the British Geological Survey reference adopted for alkaline electrolyzers in a material-intensity and procurement-risk assessment [S6]. It converts electrolyzer capacity into an initial nickel requirement for planning purposes, so it should be treated as an order-of-magnitude estimate until the stack supplier confirms its electrode specification.

At that reference intensity, a 10 MW electrolyzer implies about 8,000 kg, or 8 metric tonnes, of nickel before any project-specific adjustment [S6]. The same arithmetic gives 80 tonnes for 100 MW and 800 tonnes for 1 GW. These totals describe embodied stack material, not an annual nickel consumption rate.

The material may appear in electrodes and associated catalytic coatings rather than as bulk structural nickel throughout the electrolyzer, so procurement should distinguish active catalyst from nickel contained in inactive or recyclable assemblies.

Why the Estimate Changes Between Electrolyzer Designs

Modern designs can differ substantially in catalyst type, coating thickness, active area, and number of cells, all of which affect the amount of nickel installed per MW [S4][S9].

A reported alkaline water electrolyzer with nickel electrodes operated at a current density of 2 A/cm² and a cell voltage of 1.85 V [S7]. These operating data illustrate the electrochemical conditions the electrode must tolerate, but they do not establish one universal nickel mass per MW.

That distinction matters for buyers comparing an 800 kg/MW screening figure with a vendor quotation. A supplier may specify a total based on gross electrode area, coating loading, or complete active assemblies. Procurement should request kilograms of nickel per cell, kilograms per stack, active-area dimensions, coating formulation, and the power basis used for the calculation.

Stack Size and Hydrogen Output Are Separate Design Checks

how much nickel does an alkaline electrolyzer use per MW? - Stack Size and Hydrogen Output Are Separate Design Checks
how much nickel does an alkaline electrolyzer use per MW? - Stack Size and Hydrogen Output Are Separate Design Checks

Alkaline electrolyzer capacity cannot be inferred from hydrogen output alone because stack voltage, current density, gas purity, and operating load determine production rate [S1][S3].

These figures show why one megawatt can be represented through different equipment arrangements and operating conditions.

For nickel budgeting, the most defensible comparison is mass of nickel per rated MW under a declared operating basis. For hydrogen budgeting, the separate check is specific energy consumption, defined from stack voltage, current, and hydrogen output. Combining the two without documenting the operating basis produces a false level of precision.

Alkaline and PEM Material Requirements Are Not Interchangeable

Alkaline electrolysers are widely used in high-demand hydrogen applications, especially in chemicals, steel, and energy, and are known for reliability, scalability, and cost-effectiveness [S5].

Alkaline electrolysis carries the 800 kilograms of nickel per megawatt reference planning benchmark, while PEM and solid oxide electrolysers are identified as alternatives with distinct features [S5][S6]. A broader engineering treatment of alkaline versus PEM electrolyzer stacks is useful where the decision depends on efficiency, catalyst loading, and supply exposure rather than nickel mass alone.

Alkaline electrolysers are preferred for industries requiring high volumes of hydrogen, especially in chemicals, steel, and energy, and are known for reliability, scalability, and cost-effectiveness [S5]. Neither selection rule removes the need to validate stack-specific catalyst inventories.

Procurement Should Separate Gross and Recoverable Nickel

how much nickel does an alkaline electrolyzer use per MW? - Procurement Should Separate Gross and Recoverable Nickel
how much nickel does an alkaline electrolyzer use per MW? - Procurement Should Separate Gross and Recoverable Nickel

A material estimate should distinguish nickel in active electrodes from nickel in coatings, substrates, manufacturing scrap, and recoverable end-of-life material. The 800 kg/MW reference is a gross project-screening input unless the underlying supplier definition provides a breakdown, so it should not be entered into a recycling calculation as equivalent to recoverable supply. [S6]

Alkaline electrolyzers are built from multiple cells arranged into stacks, and each cell includes an anode, cathode, and electrolyte separator [S5]. Because cell count and electrode dimensions vary by design, procurement schedules need a clear unit boundary: kilograms per cell, kilograms per stack, kilograms per module, or kilograms for the complete electrolyzer plant.

The material basis for nickel alloy selection also differs by component. Structural nickel alloys are judged by mechanical properties and corrosion resistance, while electrolyzer electrodes are selected primarily for electrocatalytic activity, conductivity, and alkaline stability. The 800 kg/MW benchmark does not imply that all 800 kg must be high-performance nickel alloy plate.

Engineering and Commercial Limits on the Benchmark

Nickel-based alkaline systems do not face the same raw-material availability constraint as iridium-based PEM systems, but lower current density and lower efficiency can increase the number of cells and active electrode area required for a given power level [S5]. This creates an important distinction between metal intensity per MW and total plant economics.

Operating conditions also matter. The cited 2 A/cm² result at 1.85 V and the 1.91–1.93 V stabilized range demonstrate that cell voltage and current density are meaningful engineering variables, not cosmetic specifications [S7][S9]. Actual hydrogen output and degradation depend on the full stack design and operating profile, which in turn determine how much nickel equipment remains productive over its service life.

The reference benchmark is therefore useful for early screening, land-side logistics, and long-range procurement planning. It is not a substitute for a vendor bill of materials. A defensible project estimate should document rated DC power, stack count, cell voltage, operating current density, electrode area, nickel chemistry, coating thickness, and the precise included assemblies.

The next engineering checkpoint is the supplier’s nickel declaration: request kilograms per cell and kilograms per stack, reconcile them against 800 kg per MW, and identify which quantities are active catalyst, substrate, structural alloy, and recoverable scrap [S1][S2][S6].

Frequently asked questions

What nickel mass should be budgeted for a 100 MW alkaline electrolyzer?

Using the 800 kg/MW British Geological Survey reference benchmark, a 100 MW alkaline electrolyzer implies approximately 80,000 kg, or 80 metric tonnes, of nickel. This is an initial embodied-material estimate rather than an annual consumption rate, and it should be adjusted after the stack supplier confirms the electrode specification.

Can the 800 kg/MW alkaline electrolyzer nickel benchmark be used for supplier comparison?

Only as an initial screening value because catalyst type, coating thickness, active area, cell count, and the definition of installed MW can change nickel demand. Buyers should request nickel mass per cell and per stack, active-area dimensions, coating formulation, and the power basis used by the supplier.

How should procurement separate active nickel from recoverable nickel in an alkaline electrolyzer?

Estimate nickel in active electrodes and catalytic coatings separately from nickel in substrates, inactive assemblies, manufacturing scrap, and recoverable end-of-life material. The 800 kg/MW reference is a gross project-screening input and should not be treated as equivalent to recoverable supply unless the supplier provides a component-level breakdown.

Is the 800 kg/MW nickel requirement transferable from alkaline electrolyzers to PEM systems?

No. The 800 kg/MW figure is a planning benchmark for alkaline electrolysis, whereas PEM systems use iridium-bearing electrodes and do not carry the same nickel inventory. Efficiency, catalyst loading, operating profile, and supply exposure should be evaluated separately for each technology.

10 sources
  1. Introduction to Liquid Alkaline Electrolysis
  2. Green hydrogen cost reduction: Scaling up electrolysers to ...
  3. Alkaline Water Electrolysis - an overview
  4. Alkaline Water Electrolysis for Green Hydrogen Production
  5. Alkaline Electrolysers 101: Everything You Need to Know ... (Dec 19, 2024)
  6. Material Intensity, Electrode Supply and Procurement Risk (Nov 1, 2026)
  7. An alkaline water electrolyzer with nickel electrodes ...
  8. Green hydrogen production using low temperature water ... (Jan 27, 2021)
  9. Mechanical alloying of nickel-based catalysts for alkaline ...
  10. green-hydrogen-electrolyzer | Aragon Hydrogen Foundation

Need to source matching manufacturers or get a quote?

SpecForge connects industrial buyers with verified manufacturers. Submit your requirement and we will route it to matched suppliers.

Submit RFQ now →
Ask SpecForge AI