Pressure vessels are enclosed containers designed to hold liquids, gases, or vapors at pressures substantially different from ambient, with industrial operating envelopes spanning roughly 15 psig to 150,000 psi and service temperatures often above 400°C (750°F) [S4].
Standard geometries in industrial service are spherical, cylindrical, and ellipsoidal, with the cylindrical shell plus two formed heads the dominant configuration for storage and process service [S4][S6]. Buyers typically evaluate material of construction, wall thickness, corrosion allowance, pressure rating, weld quality, and code compliance (most commonly ASME BPVC Section VIII) when sourcing a vessel [S1].
ASME BPVC Section VIII: three divisions for different pressure ranges
ASME BPVC Section VIII is the dominant code for unfired pressure vessels in most industrial regions, and it is split into three divisions keyed to operating pressure [S1].
Division I covers vessels operating at internal or external pressures above 15 psig using a design-by-rule approach grounded in normal stress theory; it is the default for general industrial service. Division II provides an alternative design-by-analysis approach available at the same pressures as Division 1, with stricter material, design, and NDE rules and higher allowable stresses derived from maximum distortion energy theory. Division III applies to vessels above 10,000 psig, where specialized fabrication and enhanced safety margins are required for high-pressure containment [S1].
Function-based classification: storage, separation, reaction, heat transfer
Beyond pressure rating, pressure vessels are commonly classified by what they do in the process: storage tanks, air receiver tanks, distillation columns, heat exchangers, reactors, and boilers [S3].
Distillation columns separate liquid mixtures by vaporization and condensation, and are heavily used in crude-oil refining and chemical production. Boilers generate steam for heating and power, with shells designed for elevated pressures and temperatures. Heat exchangers transfer heat between two or more streams without mixing them, using tube bundles housed in a pressure shell, and they appear in HVAC, refrigeration, and chemical processing. Reactors carry out controlled chemical reactions in pharma and petrochemical plants, and often include agitators, baffles, or internal coils. Storage tanks hold liquids or gases at varied pressures and temperatures, and air receiver tanks buffer compressed air for pneumatic systems [S3].
Geometry-based classification: cylindrical, spherical, ellipsoidal
Vessel shape is selected from site footprint, stored product, design pressure, and budget, and three geometries dominate the catalog [S3][S6].
Cylindrical vessels with two formed end caps are the most common configuration, balancing manufacturability and cost for both gas and liquid service. Spherical vessels cost more to fabricate but maximize volume per unit wall area and are favored where footprint is constrained, for example in large LNG and LPG spheres. Ellipsoidal (2:1 or other ratios) heads on cylindrical shells are a hybrid used to optimize stress distribution at the shell-to-head transition [S3].
Industrial sectors and the three that carry the volume
Pressure vessels are used across oil and gas, chemicals, petrochemicals, power generation, pharmaceuticals, and food, but three sectors account for the majority of the installed base [S4].
Oil and gas uses pressure vessels as receivers, separators, and distillation columns, with carbon steel and stainless steel as the dominant materials of construction and complex internals such as trays and baffles supplied by specialist vendors. The chemical industry uses reactors and process vessels where chemical reactions change the contents, and many plants run multiple pressure vessels in series or parallel within a single process train. Power generation uses pressure vessels to contain steam, superheated fluids, and in nuclear plants, the reactor pressure vessel (RPV) that houses the core [S4].
Inspection, integrity, and the Japan Class 1 / Class 2 framework
Operating a pressure vessel is not a one-time code event: inspection cadence is set by API 510 in most refining and chemical sites, and by national frameworks elsewhere [S1][S5].
API 510 (Pressure Vessel Inspection Code: In-Service Inspection, Rating, Repair, and Alteration) governs ongoing maintenance, RBI, turnaround planning, repair, and alteration of operating vessels and is the reference for asset-integrity programs. Under the Japanese Industrial Safety and Health Act framework, vessels are split into Class 1 and Class 2, with Class 1 covering large, high-pressure equipment that requires manufacturing permits, installation approval, and annual performance inspection by a registered agency; Class 2 covers lower-pressure service such as household gas cylinders and small compressed-air receivers where simplified safety cases apply [S5]. Exclusion thresholds below the Class 1 boundary include gauge pressure at or below 0.1 MPa, internal volume at or below 0.04 m³, shell internal diameter at or below 200 mm with length at or below 1000 mm, or the product of gauge pressure (MPa) and internal volume (m³) at or below 0.004 [S5].
Material of construction and the move toward composites
Steel, both carbon and stainless, remains the dominant material of construction for industrial pressure vessels, with composites flagged as the next alternative [S4].
Carbon steel handles the bulk of hydrocarbon and general-purpose service, while stainless steel (commonly 304/304L and 316/316L) is specified where corrosion resistance, hygienic service, or higher temperature creep resistance is required. Composite overwrapped vessels, typically metal liners with carbon-fiber or aramid overwrap, are positioned as a future alternative to all-metal shells for weight-sensitive and high-pressure storage, including hydrogen service [S4].
Selection criteria: matching vessel type to application
Use the comparison below to map service conditions to vessel class; the trade-off is cost versus pressure capability versus inspection burden [S1][S3][S5].
For a fixed budget and standard industrial service, a cylindrical shell with ASME Section VIII Division I (design-by-rule, above 15 psig) is the workhorse. Where fatigue and efficiency dominate, Section VIII Division II design-by-analysis can be selected as an alternative to Division 1 at comparable pressures, while Section VIII Division III is required above 10,000 psig. In Japan, a plant with annual performance inspection and prefectural labor-bureau oversight points to a Class 1 vessel, while compressed-air receivers and small gas cylinders below the exclusion thresholds fall under Class 2 with simplified compliance. Internals selection then follows function: trays and packing for distillation columns, tube bundles for heat exchangers, agitators and baffles for reactors [S1][S3][S5]. Sight-glass and nozzle interface details on these vessels are governed by separate rules covered in the sight glass seal stack reference.
Trackable signals to watch: any further uptake of ASME Section VIII Division II design-by-analysis for hydrogen and high-pressure storage, and continued migration of inspection programs from fixed-interval to RBI under API 510 as plants extend turnaround intervals.