REQUEST FOR QUOTE → Request a quote
SpecForge Editorial Team

PT100 161.6 Ohms Converts to About 160°C

Table of Contents
  1. What 161.6 Ohms Means for a PT100
  2. Why the Conversion Depends on the Formula
  3. Comparison of Common PT100 Reading Methods
  4. Where the 161.5°C Figure Comes From
  5. Accuracy, Tolerance, and Measurement Error
  6. Temperature Range and Element Selection
  7. Verification Workflow for a 161.6-Ohm Reading
PT100 161.6 Ohms Converts to About 160°C

A PT100 resistance of 161.6 Ω converts to approximately 160°C, not 161.5°C, using the Callendar-Van Dusen relationship and the IEC 60751 temperature coefficient of 0.003851°C⁻¹ [S2].

The result is consistent with a PT100 resistance table in which 161.6 Ω is listed at 160°C, while the linear approximation produces a slightly different value near 159.9°C [S2][S6].

What 161.6 Ohms Means for a PT100

A PT100 has a nominal resistance of 100.000 Ω at 0°C, and its resistance rises with temperature because platinum has a positive temperature coefficient [S1][S3]. At 50°C, the standard table gives 119.397 Ω; at 100°C, it gives 138.505 Ω; at 150°C, 157.325 Ω; and at 160°C, 161.6 Ω [S2][S6].

The practical reading is therefore about 160°C. The often repeated 161.5°C result appears to confuse the measured resistance with the converted temperature or apply an incorrect coefficient. For reference, a PT100 RTD is specified by its nominal resistance at 0°C, not by its resistance at the operating temperature.

Why the Conversion Depends on the Formula

The linear coefficient form is T = (R - R₀) / (R₀ × α), with R₀ = 100 Ω and α = 0.003851°C⁻¹ [S2]. Using R = 161.6 Ω gives approximately 160.0°C. The formula is a straight-line approximation, so it does not reproduce the small curvature of the platinum resistance-temperature curve [S2].

The more complete Callendar-Van Dusen calculation gives the same practical result at this point: 161.6 Ω corresponds to approximately 160°C [S6]. The RTD temperature calculator and the resistance table therefore agree on the engineering interpretation of the reading, while the exact decimal output can vary with the approximation and coefficients used.

Do not use the coefficient in ohms per degree Celsius as a direct conversion factor. The slope near 160°C is about 0.37 Ω/°C, while the 0.003851°C⁻¹ value is the mean temperature coefficient applied to the 100 Ω reference resistance [S2][S6].

Comparison of Common PT100 Reading Methods

The main selection criterion is whether the instrument performs a curve conversion or only a linear calculation. The table below compares the relevant methods against accuracy, implementation, and suitable use. [S1]

For a field instrument, the transmitter or controller must be configured for the correct sensor characteristic, including Pt100 rather than another RTD type. A temperature transmitter that applies the proper conversion is more reliable than a display configured as a raw voltage or current input [S3].

Where the 161.5°C Figure Comes From

The resistance increment above the 100 Ω reference is 61.6 Ω. Dividing that increment by the linear coefficient of 0.3851 Ω/°C gives approximately 159.96°C, which rounds to 160.0°C rather than 161.5°C [S2]. A result of 161.5°C would imply a resistance of approximately 162.2 Ω under that linear model, so the discrepancy is larger than ordinary display rounding.

Possible causes include entering 161.6 Ω into a calculator configured for PT1000, confusing the 150°C table value of 157.325 Ω with the 160°C value, or reading a displayed result from a device with the wrong sensor scale [S2][S3]. A PT1000 input treats 161.6 Ω as a low-resistance reading near the bottom of its measurement range, not as a normal 160°C PT100 value.

Accuracy, Tolerance, and Measurement Error

The resistance value does not by itself define the accuracy of the final temperature. Element tolerance, transmitter error, lead resistance, self-heating, and installation thermal error can all shift the result. A PT100 element can be supplied in Class A, Class B, Class C, or Class T tolerance grades, with the cited product family listing F0.15, F0.3, F0.6, and F0.1 designations respectively [S4].

At 161.6 Ω, an instrument with 0.1°C display resolution may show 161.5°C while representing a converted value near 160°C, but the correct interpretation still requires checking the configured sensor type, resistance units, and lead compensation. Before replacing a sensor, verify the element resistance, lead path, input configuration, and installed wiring in that order [S3].

For high-accuracy work, use four-wire measurement or a transmitter with lead compensation so that cable resistance does not become part of the RTD measurement. The element itself should be isolated from an active input before an ohmmeter resistance check is made [S3].

Temperature Range and Element Selection

Published PT100 guidance lists an operating range of -200°C to 650°C, 100 Ω nominal resistance at 0°C, and ±0.1°C accuracy as general product characteristics [S1]. Thin-film ceramic elements are also described with a -50°C to +650°C application range and a temperature coefficient of 0.00385 [S5].

For a 160°C process measurement, thin-film and wire-wound constructions remain viable, but the stated operating range alone is not enough to approve either design. The selected element must meet the required tolerance, mechanical construction, lead material, and process conditions. TE Connectivity lists platinum thin-film elements with ceramic substrates and silver or nickel/gold lead-wire options [S4].

Class A is appropriate when tighter element tolerance is required, Class B is a common general industrial choice, and Class C or Class T may be selected when cost or construction outweighs tighter tolerance. The tolerance label does not eliminate transmitter error, drift, or self-heating, so system accuracy must be evaluated separately [S4][S6].

Verification Workflow for a 161.6-Ohm Reading

First confirm that the sensor label, drawing, or datasheet identifies a Pt100 with 100 Ω nominal resistance at 0°C. Then compare the displayed temperature with a trusted measurement at the same physical location, because a remote comparison can reflect a real process gradient rather than an instrument fault [S3].

With the circuit isolated, measure the element resistance. A finite resistance that changes smoothly when warmed confirms positive-temperature-coefficient behavior; an open circuit indicates a broken element or connection; and a resistance close to the ohmmeter lead resistance indicates a short [S3].

Finally, check the receiver configuration for Pt100, confirm the three- or four-wire connection, and verify the conversion curve. If the element is correct but the display remains wrong, the fault is more likely in configuration, lead resistance, or scaling than in the sensing element [S3].

The trackable result is clear: record 161.6 Ω as approximately 160°C for a PT100, then verify sensor type, lead compensation, and instrument configuration before accepting a displayed value of 161.5°C.

Frequently asked questions

What temperature does a 161.6 Ω PT100 resistance indicate under IEC 60751?

A 161.6 Ω PT100 resistance indicates approximately 160°C using the standard Callendar-Van Dusen conversion and the IEC 60751 temperature coefficient of 0.003851°C⁻¹. The standard PT100 resistance table also lists 161.6 Ω at 160°C.

How should a transmitter be configured for a PT100 reading of 161.6 Ω?

Configure the transmitter or controller for a Pt100 sensor with 100 Ω nominal resistance at 0°C, rather than a generic resistance, voltage, or current input. Incorrect sensor scaling, including a PT1000 configuration, can produce a misleading temperature result.

Which accuracy considerations matter when converting 161.6 Ω to temperature?

System accuracy depends on more than the element resistance because element tolerance, transmitter error, lead resistance, self-heating, and installation thermal error can shift the result. For high-accuracy measurement, use four-wire measurement or a transmitter with lead compensation.

Which PT100 element and temperature range suit a 160°C process measurement?

Both thin-film and wire-wound constructions remain viable at 160°C. Published guidance lists a PT100 operating range of -200°C to 650°C, while the thin-film option is described with a -50°C to +650°C application range; selection must also meet the required tolerance, mechanical construction, lead material, and process conditions.

6 sources
  1. PT100 temperature transducer data table
  2. RTD Temperature Calculator (PT100/PT1000)
  3. How Does a Pt100 RTD Convert Temperature to Resistance? (2026/10/13 22:01:42)
  4. Pt100 RTD Thin Film Element (2026/04/08 12:52:58)
  5. MICC Iec751 y din43760 2*16mm PT100 RTD elementos
  6. PT100 RTD Temperature Converter (2026/09/20 00:00:00)

Need to source matching manufacturers or get a quote?

SpecForge connects industrial buyers with verified manufacturers. Submit your requirement and we will route it to matched suppliers.

Submit RFQ now →
Ask SpecForge AI