REQUEST FOR QUOTE → Request a quote
SpecForge Editorial Team

Size Torque Sensors for Motor Startup Spikes

Table of Contents
  1. Separate Running Torque from Startup Shock
  2. Apply the Across-the-Line Startup Rule
  3. Compare Inline and Reaction Sensors
  4. Set Bandwidth for the Fastest Event
  5. Account for Off-Axis and Installation Loads
  6. Validate the Startup Envelope
Size Torque Sensors for Motor Startup Spikes

The selection must also cover probable running peaks, rotational speed, transient response, and non-torsional loads that can distort the measurement [S1][S2][S5].

Separate Running Torque from Startup Shock

Maximum average running torque, or MART, is the basis for preliminary sizing, but it does not represent the startup transient. For a rotating machine, Himmelstein gives MART as maximum rated horsepower multiplied by 63,025 and divided by rpm, using the lowest speed at which maximum rated power is developed [S1].

This calculation provides a conservative first pass, not a substitute for a measured startup trace. Its accuracy depends on the drivetrain model, and Himmelstein notes that a more precise peak calculation requires exact shaft-network parameters that are seldom available [S1].

Apply the Across-the-Line Startup Rule

This requirement can be larger than the overload derived from steady-state power and speed because the transient occurs before the drivetrain reaches its normal operating condition.

The electrical starting method must therefore be treated as part of the mechanical sensor specification, not as a separate commissioning detail.

Torque spikes can also make an inline measurement unreliable when the load changes abruptly during startup [S3]. The reported problem is not merely that the true torque rises, but that mounting the sensor within the driveline allows gearbox, coupling, and bearing effects to enter the measured signal [S3].

For a complete power-based starting point, sizing a torque sensor from shaft power and speed covers the steady-state calculation before startup factors and overload margins are applied.

Compare Inline and Reaction Sensors

torque sensor sizing for peak torque spikes during motor startup - Compare Inline and Reaction Sensors
torque sensor sizing for peak torque spikes during motor startup - Compare Inline and Reaction Sensors

Inline rotary torque sensors measure torque in the driven shaft and are generally the better choice when startup torque, torsional vibration, and drive-train dynamics are primary concerns. They can be implemented as circular-shaft, slip-ring, analog telemetry, digital telemetry, or dual-range devices [S5].

Reaction torque sensors have no moving parts, avoid shaft modification, and do not require an RPM rating [S5]. They are often cost-effective, but their rotating mass acts as a mechanical filter, reducing dynamic response and preventing the sensor from measuring the shaft’s true transient torque [S5].

For a low-speed test stand where only reaction torque is needed, a reaction torque sensor for nutrunner testing may be adequate. That use case does not automatically suit a high-inertia motor with a short, sharply defined startup event.

Set Bandwidth for the Fastest Event

Sensor capacity alone does not guarantee that a startup spike will be captured. The instrument sampling rate must be sufficient to record all torque changes at the relevant rpm and breakaway torque [S2]. Capacity handles the mechanical load; bandwidth determines whether the measurement chain reproduces the event.

Those ratios belong to the cited model context and should not be transferred to an unspecified sensor without confirming its frequency response and overrange behavior [S5].

Rotating sensors also require attention to critical speeds and rotational effects [S5]. A unit that is mechanically strong enough for the startup peak can still be unusable if its installation approaches a critical speed or if its signal path filters the transient. Check both shaft dynamics and the complete acquisition chain [S2][S5].

Account for Off-Axis and Installation Loads

torque sensor sizing for peak torque spikes during motor startup - Account for Off-Axis and Installation Loads
torque sensor sizing for peak torque spikes during motor startup - Account for Off-Axis and Installation Loads

Axial thrust, radial belt tension, and bending from an off-center pulley are extraneous loads that must be checked separately from torque capacity [S1]. They increase combined structural stress, can accelerate fatigue, and may affect sensor accuracy if left unaccounted for [S1][S2].

Mounting style changes the allowable loads.

The torque sensor specification should therefore state the mounting arrangement, shaft diameter, pulley geometry, axial force, radial force, overhung moment, rotation direction, and maximum rpm [S2]. For a rotating installation, the mechanical interface and any slip-ring or non-contact coupling must be selected together rather than treated as interchangeable accessories [S2].

Also specify temperature, dirt, electromagnetic interference, output protocol, bridge resistance, nonlinearity, hysteresis, creep, and environmental sealing where applicable [S2]. A shaft-mounted sensor with the right torque range can still lose data through EMI, wiring, or an underspecified conditioning system [S1][S5].

Validate the Startup Envelope

Final acceptance should compare the sensor’s overload rating with both the motor’s rated starting torque and the independently calculated probable peak torque [S1]. Where possible, capture an instrumented startup with a sampling rate and response range suitable for breakaway torque, then compare the measured peak against both limits [S2].

For production acceptance, document the motor rating, starting method, drivetrain inertia, rated power, relevant rpm, sensor range, overload rating, maximum rpm, mounting loads, and acquisition bandwidth. Repeat the check whenever the motor, coupling, gearbox, pulley alignment, or controlled-start strategy changes [S1][S2].

The decisive tracking signals are the measured peak torque and its duration against the selected overload envelope, plus confirmation that no critical-speed or signal-filtering effect distorted the startup record. A torque wrench tester checks wrench calibration rather than motor startup, but the same separation between rated range, overload capability, and acquisition bandwidth is useful during selection.

5 sources
  1. CHOOSING THE RIGHT TORQUE SENSOR
  2. Torque Sensor Selection | Torque Sensor Sizing
  3. Motor Torque Measurement Using Dual-Function Radar ...
  4. Estimation of Motor Startup Speed Profile Using Low ...
  5. How to Select a Rotating Torque Sensor

Need to source matching manufacturers or get a quote?

SpecForge connects industrial buyers with verified manufacturers. Submit your requirement and we will route it to matched suppliers.

Submit RFQ now →
Ask SpecForge AI