REQUEST FOR QUOTE → Request a quote
SpecForge Editorial Team

Type 1 vs Type 2 Sound Level Meter Accuracy Compared

Table of Contents
  1. Accuracy class and measurement chain
  2. Frequency response and documented bandwidth
  3. Selection criteria for each class
  4. Class 1 and Class 2 compared
  5. Calibration, features, and failure risks
  6. Purchase and compliance checklist
Type 1 vs Type 2 Sound Level Meter Accuracy Compared

Class 1 sound level meters require tighter accuracy tolerances and wider frequency coverage than Class 2 meters, making them the stronger choice for laboratory measurement, legal evidence, and defensible environmental surveys [S1][S3].

Type 1 and Type 2 are the older names for Class 1 and Class 2 under IEC 60651, while IEC 61672 uses the term Class and imposes more demanding accuracy, performance, and calibration requirements [S2][S5].

Accuracy class and measurement chain

The accuracy class describes the permitted performance of the complete sound level meter system, not merely the microphone capsule. IEC 61672 tolerance requirements extend across the acquisition chain, and compliance also considers the user interface and the format and detail of recorded results [S2][S4].

One reference-condition tolerance table gives ±0.7 dB for Type 1 and ±1.0 dB for Type 2 under IEC 60651 section 9.1, but these single-level, single-frequency figures do not represent every operating condition [S2].

For procurement, specify the complete standard, class, frequency range, acoustic configuration, microphone, windscreen, calibrator, and required measurements rather than treating one headline tolerance as the complete accuracy claim [S1][S4].

Frequency response and documented bandwidth

Both classes can use A, C, and Z frequency weightings, so weighting selection does not determine class by itself [S1]. The choice depends on required tolerance, usable bandwidth, documentation detail, and whether the result will be challenged [S1][S4].

Selection criteria for each class

type 1 vs type 2 sound level meter accuracy class - Selection criteria for each class
type 1 vs type 2 sound level meter accuracy class - Selection criteria for each class

Class 1 is for precision work: laboratory and calibration measurements, professional acoustic analysis, environmental assessments requiring defensible data, legal or regulatory reporting, and low-level environmental surveys [S1][S2].

Class 2 is for general field measurements, spot checks, basic surveys, occupational-noise checks, and cost-sensitive monitoring where tighter precision does not affect the decision [S1][S2]. Workplace noise measurement under OSHA or NIOSH guidance can use Class 2 instruments, while some municipalities or governing agencies specifically require Class 1 compliance for event measurements [S4].

A Class 1 meter is not automatically required for every compliance task. Check the applicable regulation, jurisdiction, and contract before ordering.

Class 1 and Class 2 compared

Class 1 systems are required to provide more detailed documentation than Class 2 systems [S4].

Class 2 wins on acquisition cost and suitability for routine surveys, since it meets looser tolerances across a narrower useful bandwidth [S1][S3]. It is the more practical option for general industrial, commercial, educational, recreational, and residential sound-level checks where the result does not require laboratory-grade defensibility [S4].

Dynamic range must be checked separately from class. Class alone does not guarantee adequate range, low self-noise, microphone sensitivity, or the required frequency weighting.

Calibration, features, and failure risks

type 1 vs type 2 sound level meter accuracy class - Calibration, features, and failure risks
type 1 vs type 2 sound level meter accuracy class - Calibration, features, and failure risks

Do not infer total measurement uncertainty from the class label alone. IEC 60651 reference tolerances cover only one level and one frequency, while the full measurement chain includes microphone response, windscreen correction, interface tolerances, displayed results, and calibration status [S2][S4].

Common failure modes include using a Class 2 meter where the governing rule requires Class 1, recording a measurement outside the instrument’s upper level limit, losing valid data because the selected range is too narrow, and treating a single-frequency tolerance as proof of accuracy across the full measurement chain [S2][S4].

Calibrator compatibility, periodic calibration, windscreen use, microphone orientation, environmental limits, and the required statistic such as Leq should be confirmed before deployment. The A-, C-, and Z-weighting options and optional FFT or octave-band functions do not upgrade a meter from Class 2 to Class 1 [S1].

Purchase and compliance checklist

Specify IEC 61672 class and standard edition in the purchase order, then require evidence that the supplied configuration meets the class rather than relying on a distributor statement. Older IEC 60651 and IEC 60804 instruments may remain usable in many applications, but new procurement should use IEC 61672 because it makes more demanding accuracy, performance, and calibration provisions [S2].

Record the intended application, jurisdiction, required frequency range, expected sound pressure range, frequency weighting, statistical outputs, documentation format, microphone and windscreen configuration, and calibrator model [S1][S4]. For legal evidence, environmental audits, laboratory work, or disputed results, select Class 1. For routine workplace and general field surveys, Class 2 is usually the cost-effective choice when the governing requirement permits it [S2][S4].

The next trackable check is the governing document: confirm whether it names a class, standard edition, tolerance, measurement configuration, and calibration requirement. That comparison should be completed before comparing instrument price, because a lower-cost meter that fails the specified class is not a valid option.

Frequently asked questions

What accuracy tolerance and frequency coverage should I specify for a Class 1 sound level meter?

Specify Class 1 compliance under IEC 61672 when precision, defensibility, or broad bandwidth is required. The cited comparison gives approximately ±1 dB at 1000 Hz and a typical frequency coverage of 16 Hz to 16 kHz, compared with approximately ±2 dB and 20 Hz to 8 kHz for Class 2.

When is a Class 2 sound level meter sufficient for industrial noise measurements?

Class 2 is generally suitable for general industrial sound checks, occupational-noise assessments, spot checks, and basic surveys where tighter precision does not affect the decision. OSHA or NIOSH workplace measurements may use Class 2, but jurisdictions or contracts requiring Class 1 must be checked before procurement.

Does choosing A-, C-, or Z-frequency weighting determine whether a meter is Class 1 or Class 2?

No. Both Class 1 and Class 2 meters can use A, C, and Z frequency weightings, and optional FFT or octave-band functions do not upgrade a Class 2 instrument to Class 1. The class is determined by the applicable IEC 61672 performance requirements and documentation.

What measurement range and environmental features should I verify before purchasing a sound level meter?

Check the usable range separately from accuracy class: a common range is 30 to 130 dB, while environmental surveys may require measurements down to 25 dB and industrial applications may require at least 140 dB. Also verify windscreen corrections, calibrator compatibility, microphone sensitivity, calibration status, environmental limits, and the required statistic such as Leq.

8 sources
  1. Class 1 vs Class 2 Sound Level Meter: A Complete Guide (Oct 21, 2025)
  2. Type and Class of a Sound Level Meter - A Definition
  3. What's the Difference Between a Class 1 and Class 2 ...
  4. Class 1 vs. Class 2 SPL Measurement (Sep 10, 2024)
  5. Class 1 vs Class 2 Sound Level Meter: Which One Wins? (Aug 13, 2026)
  6. Sound Level Meters Explained: Class 1 vs Class 2, Leq ...
  7. What is the difference between Class 1 and Class 2 sound ...
  8. What is the Difference Between a Class 1 and Class 2 ... (Jun 11, 2021)

Need to source matching manufacturers or get a quote?

SpecForge connects industrial buyers with verified manufacturers. Submit your requirement and we will route it to matched suppliers.

Submit RFQ now →
Ask SpecForge AI