Universal thermocouple transmitters accept Type J, K, T, E, R, S, B and N inputs, then convert them to 4–20 mA or 0–10 V DC outputs for controllers and other instrumentation [S2][S3].
Available configurations include single- and dual-channel models, two-, three-, and four-wire models, loop-powered models, current, voltage, and 4–20 mA outputs, and some models configured by USB, while the XTH2 is configured with Free ProSense Field Device Configurator software and an XT-USB cable [S2][S5].
Eight thermocouple types in one input module
Universal input does not mean that every sensor type has the same useful range. The transmitter must apply the correct reference-junction compensation and sensor polynomial for the selected type, and the configured span must remain inside that sensor's valid limits [S5].
Type K is the broadest common industrial choice, while Type J covers a different useful span. The HHMD handheld display illustrates the range distinction: its Type K setting spans -200 to 1372°C, its Type J setting spans -210 to 1200°C, and its Type T setting spans -250 to 400°C, all at 1°C resolution [S4].
For additional context, a thermocouple is the sensing element, not the transmitter. The transmitter handles cold-junction compensation, linearization, scaling and electrical output, so sensor type selection and transmitter configuration must be treated as one engineering decision.
Output and wiring options change installation requirements
Two-wire transmitters use the same pair for loop power and signal, which reduces installation wiring but requires the transmitter to operate from the available loop supply. The TX13 is specified as a two-wire, 4–20 mA unit accepting Types K, J, N, E, T, R, S and millivolt inputs [S7].
The cited range includes two-, three-, and four-wire models with current, voltage, or 4–20 mA outputs [S2]. The XTH2 is powered by 10–36 V DC [S5].
Loop-powered head-mount models can reduce field wiring and installation time. The XTH2 operates from 10–36 V DC, provides a reverse-polarity-protected input, and offers a linearized two-wire output configurable as 4–20 mA or 20–4 mA [S5]. The engineering choice between two-wire and four-wire temperature transmitter wiring should be driven by power availability, isolation requirements and field-wiring limitations.
Universal input versus fixed-type transmitters

A fixed-type transmitter is simpler to commission and can reduce setup error, while a universal transmitter is valuable when sensors change, several thermocouple types exist on one line, or maintenance staff need one spare to cover multiple circuits [S2][S3].
The comparison below separates the main options by sensor flexibility, output flexibility, installation burden and commissioning effort. The entries summarize the configurations documented across the available manufacturer information rather than treating all products as electrically identical.
Type-by-type range and application fit
Type K is a practical default for many process measurements, but the transmitter still must be checked against the actual sensor range and required measurement span. The XTH2 accepts Types J, K, T, E, N, R, S, B and additional lettered thermocouple families, with measurement limits configured within the selected sensor type's full range [S5].
Types R and S cover high-temperature applications and require correct linearization, a detail covered in Linearize Type R and S Thermocouple Outputs. Type B also serves high-temperature measurement, while Type N provides another nickel-alloy option for industrial temperature measurement [S2][S3].
Types T and E suit lower-temperature ranges. The HHMD specifies Type T from -250 to 400°C and Type E from -210 to 1000°C, with an overall instrument accuracy of ±0.05% of reading plus 0.7°C [S4]. These limits belong to the handheld display, not automatically to every transmitter, so the transmitter datasheet remains controlling.
Configuration errors outweigh extra functions

The most common specification failure is not selecting the wrong output, but fitting the right universal transmitter and leaving the sensor type, polarity or scale incorrectly configured. A unit that lists eight thermocouple types still requires the technician to select the matching type after installation [S2][S3].
Reference-junction compensation is another critical check. The XTH2 permits internal, external or user-defined fixed-value compensation, and it supports configurable upscale or downscale response for lead-break or short-circuit detection under NAMUR NE 43 [S5]. Copper junction blocks, extension wires and terminal arrangement must therefore be treated as part of the measurement accuracy calculation.
Polarity also has to be checked at the sensor and transmitter terminals. Reversing Type J, K or T leads reverses the thermocouple voltage and can drive the measured value toward the wrong end of the scale. Commissioning should include a known input check, loop-current verification at the controller and a test of the configured sensor-break response [S5][S8].
Electrical and environmental limits narrow the selection
Power supply, output load, isolation and operating environment must be verified before a universal transmitter is accepted. The XTH2 operates from a 10–36 V DC supply, so nominal 24 V DC power does not establish compatibility by itself [S5].
The ST132 converts a millivolt or thermocouple sensor input into a proportional 4–20 mA control signal, while the XTH2 provides 2 kVAC isolation between input and output and a selectable digital filter time constant [S5][S8]. These features solve different problems: the output interface must satisfy the controller loop, and the filter may suppress unwanted fluctuations without being used as a substitute for correct sensor placement.
Environmental requirements remain equally specific. The HHMD operates from -20 to 60°C at up to 80% relative humidity without condensation, uses six AAA batteries and has a stated typical battery life of 250 hours [S4]. Those figures describe a portable display, not a field transmitter, whose enclosure, terminals and mounting method may impose different limits.
Applications and equipment boundaries

A universal thermocouple transmitter is appropriate for furnaces, ovens, kilns, heat-treatment equipment, process lines and test benches where the installed sensor may be Type J, K, T, E, R, S, B or N. Two-wire versions suit remote field points with available loop power; four-wire versions suit installations requiring separate power, isolated outputs or local bus voltage [S2][S7].
It is not a universal replacement for every temperature sensor. A dedicated RTD transmitter is preferable when the field device is Pt100 or another RTD, and a dedicated RTD-to-analog temperature transmitter must be used unless the product explicitly supports RTD input. Likewise, a transmitter listed only for thermocouple inputs cannot be assumed to accept a 4–20 mA temperature signal.
Panel displays, portable readouts and process transmitters also serve different roles. The HHMD accepts four probes, provides four-digit primary and five-digit secondary LCD fields, samples once per second, and calculates maximum, minimum, average, T1–T2, T3–T4 and hold values [S4]. That is a useful diagnostic instrument, not a replacement for a permanently installed 4–20 mA process transmitter.
Acceptance checklist for universal inputs
A sound acceptance test records the exact thermocouple type, sensor manufacturer, polarity, measurement range, configured output span, loop supply, controller value and reference-junction arrangement. Published universal transmitters cover at least the eight lettered types in this selection, but each model differs in channel count, supply range, isolation and configuration method [S2][S3][S5].
For procurement, use the transmitter datasheet for electrical limits and the sensor datasheet for the permitted temperature range. Match the sensor type list explicitly, confirm 4–20 mA versus 0–10 V DC, verify 7–32 V DC or the stated model-specific supply, and decide whether local programming, USB configuration or DIP switches fit the maintenance regime [S2][S5].
Track two procurement signals before release: confirmation that the selected input module includes all eight required Types J, K, T, E, R, S, B and N, and a signed commissioning record showing the correct cold-junction compensation, sensor polarity, configured span and 4–20 mA loop reading. Those checks prevent a universal transmitter from becoming a universal troubleshooting exercise.