A 6 m flexible shaft can lose more power than a 4 m shaft, but the 50% length increase does not imply a 50% efficiency loss.
The comparison applies to industrial power-drive assemblies using flexible shafts with cores, bearings, couplings, and operating speeds specified for the driven equipment [S1][S3].
What determines the 4 m versus 6 m loss?
Flexible shafts transmit rotational power across offsets and curves, but shaft length affects bending deflection, critical speed, support reactions, and the torque needed to overcome those loads [S1][S3].
A flexible shaft has weight that depends on its core diameter and length, and its mounting condition can apply an additional load to the shaft end [S3].
The useful comparison is therefore not “4 m versus 6 m” alone. It is 4 m versus 6 m at the same torque, rpm, core size, bearing arrangement, alignment, and bend geometry. If those variables are held constant, the longer shaft generally has more parasitic loss because it carries more mass and develops greater deflection, but the available research does not establish a universal percentage loss for either length [S1][S3].
Efficiency and power-loss comparison
Flexible-shaft systems are reported as 90% to 95% efficient overall [S5]. That range is a system-level indication rather than a guaranteed value for either a 4 m or 6 m installation.
On a stated input of 1.00 kW, 90% efficiency corresponds to 0.90 kW output and 0.10 kW loss, while 95% efficiency corresponds to 0.95 kW output and 0.05 kW loss. The difference between these endpoints is 0.05 kW at that operating point. These calculated examples are not manufacturer guarantees for 4 m and 6 m shafts; they show why an efficiency percentage must be tied to actual operating conditions [S5].
The comparison also needs a consistent measurement boundary. Include the core, both bearings, couplings, and any gearbox driven by the shaft if the operator evaluates total package power. A long shaft with one bearing arrangement will not produce the same result as a short shaft with different supports, so a procurement comparison that uses nameplate output alone is incomplete [S1][S3].
Selection criteria for the shorter shaft

A 4 m shaft is the preferable starting point when the drive path permits it, because reducing unsupported length can reduce deflection and support reaction while simplifying the installation [S1][S3].
It is suitable for equipment where the motor and driven element can be connected with less routing, the 4 m route avoids sharp offset changes, and the shaft can be supported without over-constraining its motion. Standard assemblies can be configured for power drive or remote-control service and use standard ball-bearing or plain-bearing units [S1].
The 4 m option is not automatically the lower-loss choice. If it requires a tightly bent routing, additional coupling transitions, poor bearing alignment, or a much smaller core to meet installation clearance, those penalties can outweigh the benefit of the shorter route. Flexible shafts tolerate misalignment more readily than solid shafts, but the assembly still needs adequate support and proper routing [S1][S5].
When the 6 m shaft is justified
A 6 m shaft is justified when the physical layout requires that reach and a smaller-diameter core would otherwise be needed to meet clearance or weight limits [S3].
Flexible shafts allow substantial routing freedom, including right-angle and offset arrangements, while replacing several rigid-shaft components. One manufacturer states that flexible shafts permit a full 180° offset while maintaining high efficiency [S5]. Those figures describe routing capability, not a guarantee that every 6 m core will operate at the same efficiency or rpm.
For a 6 m installation, specify the core diameter, material, lay direction, maximum operating speed, rated torque, bearing type, support locations, bend radii, and required service life as one package. Longer unsupported runs increase the sensitivity to alignment and vibration, and the shaft’s own weight becomes more significant [S3].
Critical comparison by decision criteria

For loss specifically, compare measured input and output power at the same operating point. The calculation is P_loss = P_input - P_output, and efficiency is P_output divided by P_input, expressed as a percentage. Test or obtain manufacturer data for the exact 4 m and 6 m assemblies, including bearing and coupling losses, rather than applying the same 90% to 95% range to both [S5].
For installation, count bearings, supports, couplers, and routing changes. For maintenance, include bearing condition, core inspection access, and the effect of the drive’s vibration envelope [S1][S2].
Limits, failure modes, and applicable users
This comparison is for industrial rotary power transmission, not golf shafts or remote-control mechanisms. Flexible shafts are appropriate for industrial and medical rotary motion, but power drive and remote-control cores serve different duties [S1][S5].
The principal failure mechanisms are fatigue fracture associated with repeated deflection, excessive support or end loading, misalignment, bearing wear, and operation outside the shaft’s rated speed or torque. Shaft weight and mounting-induced loads increase with length, while the allowable core and support arrangement determine whether a 6 m span is mechanically practical [S2][S3].
Flexible shafts are not suitable where a rigid coaxial connection is mandatory, where the route cannot be arranged with adequate bend radii, or where a 6 m run requires unsupported flexing beyond the manufacturer’s design limits. A power mixer or power trowel also requires a duty-specific gearbox and clutch arrangement, so shaft length alone does not determine whether its driven tool receives adequate speed and torque [S1].
Specification and sourcing requirements

Issue the same specification sheet to suppliers, including rated power or torque, rpm, shaft length, core diameter, material, bearing type, bend geometry, mounting, and operating environment. Elliott’s design guidance provides a Customer Design Specification Sheet and separates flexible-shaft design considerations from assembly selection, which is the correct procurement structure for comparing 4 m and 6 m alternatives [S1].
Require each candidate to state whether its quoted loss includes the core, bearings, couplings, and input or output measurement locations. Do not convert the 90% to 95% published efficiency range into a fixed 5% to 10% loss unless the supplier supports that claim for the specified assembly and operating point [S5].
For final selection, request one test point at the rated torque and rpm plus one service point, then compare delivered output power, shaft deflection, bearing reactions, and expected fatigue life. The decision should favor the 4 m shaft when route and load conditions are equivalent, while retaining the 6 m option when routing distance, core weight, or installation geometry makes it the only compliant assembly [S1][S2][S3].