REQUEST FOR QUOTE → Request a quote
SpecForge Editorial Team

A356 Gravity Die Cast vs Sand Cast Tensile Properties

Table of Contents
  1. Decision Criteria for A356 Casting Processes
  2. Tensile Strength and Ductility Compared
  3. Cooling Rate and Microstructural Refinement
  4. Porosity, T6 Treatment, and Failure Limits
  5. Tooling, Volume, and Surface-Finish Tradeoffs
  6. Use Cases and Alloy Modifications
  7. Specification and Qualification Requirements
A356 Gravity Die Cast vs Sand Cast Tensile Properties

When selecting A356-T6 gravity die casting, consider production volume, wall thickness, heat-treatment requirements, and welding requirements [S3].

The comparison applies to A356 aluminum structural castings, with the governing variables being casting process, temper, section thickness, solidification rate, porosity, and defect control [S1][S4].

Decision Criteria for A356 Casting Processes

A356 is an Al-Si-Mg casting alloy containing 6.5–7.5% silicon and 0.25–0.45% magnesium under ASTM B26/B26M; magnesium enables strengthening by heat treatment, while silicon supports fluidity and casting quality [S4].

Use gravity die casting for medium-volume structural parts that require heat treatment, moderate dimensional control, and higher strength than a comparably sectioned sand casting. Use sand casting for prototypes, large parts, complex cores, and volumes that cannot justify permanent tooling [S3][S4].

Do not use a generic as-cast tensile value as an acceptance requirement. Section thickness, cooling rate, porosity, fill turbulence, and T5 or T6 processing can shift the result, so the purchase specification should identify the process and temper separately [S4].

Tensile Strength and Ductility Compared

That ductility advantage matters for impact loading, strain redistribution, repair welding, and fatigue-sensitive structures.

This comparison supports gravity casting when tensile strength, ductility, and repeatability matter more than one-time tooling cost. Sand casting remains the lower-tooling route for low volume, oversized parts, or geometries that would make a permanent die uneconomic [S3][S4].

Cooling Rate and Microstructural Refinement

gravity die cast vs sand cast A356 tensile properties - Cooling Rate and Microstructural Refinement
gravity die cast vs sand cast A356 tensile properties - Cooling Rate and Microstructural Refinement

Sand castings cool at roughly 0.1–1 K/s, gravity die castings at about 1–20 K/s, and high-pressure die castings reach several hundred kelvin per second near the die face [S3].

The finer structure of gravity castings raises strength and improves fatigue behavior relative to slowly cooled sand castings [S3]. Sand casting still offers a decisive geometry advantage because collapsible sand cores can create internal passages and cavities that are expensive or impractical in a permanent mold [S4].

Design comparisons should therefore balance metallurgical refinement against fill complexity. If the gravity die casting die cannot feed every section, riser, or cored feature without turbulence or shrinkage, a sand route may produce a sounder part despite its coarser structure.

Porosity, T6 Treatment, and Failure Limits

Slow gravity fill with an intact metal front produces less entrapped gas than conventional high-pressure die casting, allowing both gravity and sand castings to undergo solution treatment and aging to T6 [S3]. Conventional HPDC cannot normally be solution treated because compressed gas expands above about 450 °C and can blister the casting [S3].

Gas porosity therefore separates gravity die casting from conventional high-pressure die casting more clearly than it separates gravity casting from sand casting. Both gravity and sand routes can support T6 treatment, while gravity casting adds finer structure, faster cooling, and better repeatability [S3][S4].

The governing gravity-casting defects are shrinkage misfeed, cold shuts, oxide films, and turbulence-generated porosity. Gate and riser placement control shrinkage, while tilt pouring reduces turbulence and supports directional solidification [S5]. The process sequence includes mold preheating and coating, gravity fill, solidification, and ejection [S5].

Tooling, Volume, and Surface-Finish Tradeoffs

gravity die cast vs sand cast A356 tensile properties - Tooling, Volume, and Surface-Finish Tradeoffs
gravity die cast vs sand cast A356 tensile properties - Tooling, Volume, and Surface-Finish Tradeoffs

Sand casting needs a new bonded-sand mold for each part, while gravity casting uses a reusable steel or iron die and therefore incurs permanent tooling expenditure [S1][S5].

The permanent mold can reduce machining and cleanup work, but this advantage is conditional on good fill, adequate gate and riser design, and die-life planning [S5].

For short runs, sand casting avoids permanent-tool amortization. For repeated production, the reusable gravity die casting machine and coated die create the route toward stable section dimensions and lower per-part cleanup. The mold trial should be treated as a process-capability trial, not merely a dimensional fit check [S5].

Use Cases and Alloy Modifications

A356-T6 gravity castings fit automotive and engineered structural parts, pump housings, industrial equipment, and other weight-sensitive components where heat treatment, weldability, ductility, and moderate tolerances are required [S4]. Sand casting fits large housings, low-volume prototypes, complex internal passages, and geometries with insufficient economic justification for a permanent mold [S4].

Scandium-modified A356 demonstrates the metallurgical ceiling under controlled gravity die casting. Samples containing 0.6 wt.% Sc, solution treated at 540 °C for 8 hours, water quenched, and artificially aged at 160 °C for 6 hours reached 338 MPa tensile strength and 118 HV after treatment; grain size fell to 16 µm from 40 µm in original A356 [S2].

Those Sc-A356 results came from gravity die-cast specimens prepared to ASTM B557-06, not unreinforced A356 production parts [S2]. They show the value of alloy and heat-treatment development, but they do not justify substituting the 338 MPa result for an A356-T6 purchase specification.

Specification and Qualification Requirements

gravity die cast vs sand cast A356 tensile properties - Specification and Qualification Requirements
gravity die cast vs sand cast A356 tensile properties - Specification and Qualification Requirements

State the alloy as A356, the process as gravity die casting or sand casting, the temper as T5 or T6, and the governing product or material specification. ASTM B26/B26M defines A356.0 composition, while ASTM B557-06 was the specimen-production standard used in the Sc-A356 gravity-casting study [S2][S4].

Require tensile testing on representative cast test bars or qualification castings, with section thickness and test location controlled. EN 1706 provides the cited A356-T6 cast test-bar reference values of 290 MPa tensile strength, 210 MPa yield strength, and 4% elongation [S5]. For production acceptance, add X-ray or radiographic assessment where internal integrity governs fatigue or pressure-tightness performance.

Keep the process distinction visible in the drawing and purchase order. A drawing that says only “A356-T6” leaves the foundry free to choose sand or gravity casting, even though those routes differ in cooling rate, tolerance capability, machining allowance, and expected tensile performance [S3][S4].

Qualify the intended route with representative geometry, measured section properties, and defect acceptance limits, then track changes in casting supplier, die condition, section thickness, or heat-treatment batch for confirmation testing.

Frequently asked questions

What tensile and yield strengths should be specified for A356-T6 gravity die castings?

A356-T6 gravity die castings typically provide 270–310 MPa tensile strength and 200–240 MPa yield strength. The purchase specification should identify both the gravity-casting process and T6 temper rather than rely on a generic as-cast tensile value.

When is sand casting more practical than gravity die casting for A356 parts?

Sand casting is generally preferable for prototypes, large parts, complex internal passages requiring collapsible cores, and volumes that cannot justify permanent tooling. Gravity die casting is better suited to medium-volume structural parts needing heat treatment, stronger properties, and better dimensional repeatability.

What cooling-rate and microstructural differences distinguish A356 gravity die castings from sand castings?

Sand castings cool at roughly 0.1–1 K/s versus about 1–20 K/s for gravity die castings. Their secondary dendrite arm spacings are approximately 50–100 µm and 25–50 µm, respectively, with the finer gravity-cast structure contributing to higher strength and improved fatigue behavior.

5 sources
  1. Die Casting vs. Sand Casting: The Complete Guide to ... (Apr 7, 2026)
  2. Effect of heat treatment on gravity die-cast Sc-A356 ...
  3. Die Casting vs Sand Casting vs Gravity Casting Compared (Aug 6, 2026)
  4. A356 Aluminum Casting: Properties & Applications (Oct 14, 2026)
  5. Aluminum Gravity Casting Process Selection Guide (Aug 28, 2026)

Need to source matching manufacturers or get a quote?

SpecForge connects industrial buyers with verified manufacturers. Submit your requirement and we will route it to matched suppliers.

Submit RFQ now →
Ask SpecForge AI