A ball-nut wiper protects the screw-to-nut interface, while a bellows cover encloses exposed screw sections and excludes chips, coolant and debris over the working stroke [S2][S3].
For most machines, specify both where sharp metal chips reach the nut and the exposed screw, provided the cover's compression, extension, airflow and service clearances are validated [S1][S2].
Different Protection Boundaries
Ball nut wipers address the local boundary where the screw enters the nut. Bellows covers address a wider physical boundary around the exposed shaft, but their joints, end frames, mounting hardware and access openings remain potential entry paths [S2][S3].
A wiper alone does not protect support bearings, couplings, exposed screw sections or the drive end. Conversely, a cover does not automatically provide a correctly specified wiper at the ball nut [S2][S3]. The relevant background for the screw itself is covered in the ball screw entry.
Wiper Types by Contaminant
The basic construction differences for a ball spline are separate, because spline sealing requirements do not establish a ball-screw wiper specification.
Decision Comparison by Operating Condition

Cost is the first comparison criterion: a wiper is a local, nut-mounted component, while a bellows cover requires a flexible body, end frames, guides or attachments and sufficient installation space. The cover also needs motion-cycle validation, whereas the wiper mainly requires nut fit, shaft diameter and wiper construction checks [S2][S3][S6].
Protection capacity is the second criterion. A brush or contact wiper removes material at the nut entry, but it leaves exposed shaft sections uncovered. A bellows can isolate the shaft from the external environment, but contraction and expansion can create airflow that draws particles inward or lifts settled dust [S1].
Service life and integration are the third and fourth criteria. A wiper adds shaft contact friction, while a bellows introduces compression, extension, attachment and accumulated-material maintenance. Lubrication access and service clearance must be checked with the selected protection installed [S2]. A machine with heavy chip transport toward the nut generally needs a contact wiper plus a cover; a machine with only large, dry chips at the nut may be adequately served by a suitable wiper without adding a full cover [S1][S2].
Recommended Configurations by Use Case
For a CNC machining axis with sharp metal chips, use a contact wiper at each exposed ball nut and add a bellows where the screw travels through a chip-producing zone. The wiper controls material entering the nut, while the cover limits deposition on the moving shaft [S1][S2].
For coolant, detergent or splash exposure, specify an elastomer compatible with the actual fluid and temperature, then verify the complete assembly because a flexible cover does not establish chemical compatibility for every attached component [S2][S5]. Published material examples include NBR for oil resistance from -30 °C to +100 °C and silicone rubber from -60 °C to +250 °C; these ranges still require application-specific confirmation [S5].
For a wood router or similar dusty machine, a brush wiper can remove larger wood chips at the nut. A cover remains an option where wood dust accumulates on the exposed screw, but its compression cycles, material durability and tendency to stir settled dust must be checked [S1][S4].
Cover Geometry, Airflow and Installation

A bellows cover must be reviewed in both compressed and extended conditions, at both travel limits, with the nut, attachments, grease connections and nearby structure shown. A cover that appears adequate at mid-stroke can interfere at an endpoint or block inspection and lubrication access [S2].
Request the bellows body, end frames, guides, fasteners and mounting details as a defined assembly, then record the compressed and extended dimensions. Also define how trapped material will be removed without driving it into the nut or damaging the cover [S2][S3]. Air movement caused by contraction and expansion remains a functional limitation even when the cover fully overlaps the screw [S1].
Maintenance and Acceptance Checks
Inspect the screw, wiper lip or brush, bellows folds, clamps and mounting points at defined intervals. The cited maintenance guide proposes daily visual inspection, monthly surface cleaning, quarterly seal-integrity checks and annual replacement evaluation, but the machine's actual contamination rate and maintenance policy should determine the interval [S5].
For commissioning, verify that the nut wiper matches the exact screw diameter and nut configuration; catalog wiper options differ between nuts and are not automatically interchangeable [S2][S6]. Confirm full travel without cover interference, check for chips trapped at both travel ends, and demonstrate that lubricant replenishment remains possible [S2].
If the cover collapses, show cracking, develops excessive movement resistance or leaves chips inside, investigate alignment, attachment stiffness, material compatibility, lubrication and accumulated debris rather than treating the symptom as a seal-life problem [S2][S5]. The next traceable engineering evidence is the approved assembly drawing listing the exact wiper, cover compressed and extended dimensions, elastomer compound, permitted temperature, cleaning fluid and lubrication access [S2][S3][S5].