REQUEST FOR QUOTE → Request a quote
SpecForge Editorial Team

C51000 vs C52100 vs C54400 Wrought Tin Bronze Selection

Table of Contents
  1. Composition defines the alloy family
  2. Decision criteria: strength, fatigue, machining, and joining
  3. Recommended grade by use case
  4. Form, temper, and manufacturing route
  5. Thermal limits and failure modes
  6. Standards and purchasing controls
C51000 vs C52100 vs C54400 Wrought Tin Bronze Selection

C51000 and C52100 are wrought copper-tin alloys with approximately 5% and 8% tin, respectively, while C54400 contains about 4% lead and 4% zinc for improved machinability.

Use C51000 for springs, electrical contacts, fasteners, and formed components; use C52100 where greater strength and wear resistance dominate; use C54400 for turned and milled parts where controlled lead additions justify improved machinability [S4][S6][S7].

Composition defines the alloy family

C52100 meets the requirements of ASTM B139 for C52100. Composition must be checked against the applicable product specification because product form, temper, and test method can change what the buyer must specify and how the material is verified.

C51000 has a nominal composition of approximately 95% copper, 5% tin, and 0.03–0.35% phosphorus. C54400 contains about 4% lead and 4% zinc. The two alloys share about 93% of their average composition, but the leaded free-machining addition changes both behavior and handling requirements [S3].

C52100 is the high-tin member of this group at approximately 8% tin. Its higher tin level supports greater tensile strength and wear resistance than C51000, and it meets ASTM B139 requirements for C52100 [S7][S8]. For procurement, describe C52100 as an 8% tin wrought phosphor bronze and confirm the governing ASTM product standard rather than treating it as a 5% alloy with a strength adjustment.

Decision criteria: strength, fatigue, machining, and joining

On strength and fatigue behavior, C51000 is the general-purpose wrought choice: its published tensile-strength range is 330–780 MPa, its elastic modulus is 110 GPa, and its Rockwell B hardness range is 26–97 [S3]. C52100 provides substantially higher tensile strength than C51000 and is suited to load-bearing wear applications [S7].

On machining, Phosphor bronze such as C51000 is harder to machine. C54400 adds about 4% lead and 4% zinc, and one supplier identifies its machinability rating as 80 [S6]. That is the main commercial reason to substitute C54400 for C51000, not a claim of higher inherent strength.

C51000 has a thermal conductivity of 77 W/m·K and a coefficient of thermal expansion of 18 µm/m·K; C54400 is listed at 86 W/m·K and the same 18 µm/m·K [S3]. C51000 therefore remains suitable for conductive spring and contact applications, while C54400 offers essentially comparable conductivity with improved cutting behavior [S3][S5].

Recommended grade by use case

C51000 vs C52100 vs C54400 wrought tin bronze composition - Recommended grade by use case
C51000 vs C52100 vs C54400 wrought tin bronze composition - Recommended grade by use case

For springs, retain C51000: it is identified as the wrought spring grade, it covers fasteners under alloy F468, and its strength rises from about 46,000–50,000 psi annealed to approximately 96,000 psi in extra-hard temper [S5][S6]. Cold rolling, drawing, bending, and stamping suit this alloy because phosphorus supports stiffness and spring performance while the material tolerates cold work [S4][S5].

For bushings, thrust washers, gears, and heavy-load, low-speed wear components, select C52100 when the design can use its higher strength and wear resistance [S1][S7][S8]. For machined connectors, small precision parts, fasteners, and components produced on automatic lathes, C54400 is the practical choice where its 80 machinability rating outweighs the handling and end-use constraints associated with 3.5–4.5% lead [S3][S6].

C54400 should not be selected automatically for any bronze component. Lead imposes restrictions in applications subject to public-health, plumbing, food-contact, environmental, or customer-specific requirements, and the composition alone does not establish suitability for a finished article. For demanding formed springs, fatigue-sensitive contacts, and aerospace hardware, specify C51000 or C52100 under the relevant product and aerospace specifications rather than substituting the free-machining grade [S4].

Form, temper, and manufacturing route

Specify wrought material as sheet, strip, rod, bar, tube, or wire, and state the required temper. C51000 strength varies sharply by temper: about 46,000–50,000 psi annealed, 70,000 psi half hard, 84,000 psi hard, and 96,000 psi extra hard [S5]. A drawing that names only C51000 leaves an important strength variable undefined.

Wrought versus cast is a separate decision. C51000 and C52100 are wrought alloys intended for rolling, drawing, stamping, machining, and cold forming; common cast bearing bronzes belong to a different product family [S5]. The tin bronze reference distinguishes traditional tin bronzes containing approximately 3–14% tin from alloys modified with phosphorus, zinc, lead, or nickel for properties such as machinability, castability, and fatigue resistance [S1].

For produced parts, set minimum tensile strength, elongation, hardness, grain direction, surface condition, and inspection requirements in the purchase specification. The material grade defines composition; it does not by itself guarantee a particular hardness or tensile strength in every product form and temper.

Thermal limits and failure modes

C51000 vs C52100 vs C54400 wrought tin bronze composition - Thermal limits and failure modes
C51000 vs C52100 vs C54400 wrought tin bronze composition - Thermal limits and failure modes

Published comparison data place the maximum mechanical-use temperature of C51000 at 190 °C and C54400 at 170 °C. Their liquidus and solidus temperatures are listed as 1,050 °C and 960 °C for C51000, and 1,000 °C and 930 °C for C54400 [S3]. These values support comparison, but component design should use the limits of the purchased product specification and the finished part.

The main failure trade-off is fatigue capability versus machining efficiency. C51000 can provide a higher absolute tensile-strength ceiling, up to 780 MPa in the comparison data, and is a better spring alloy when cold-worked [S3][S5]. C54400 can reach 720 MPa and much higher hardness, with Rockwell B listed at 67–93, but it sacrifices the unalloyed or low-lead processing behavior of C51000 [S3].

Thermal expansion is 18 µm/m·K for both C51000 and C54400, so dissimilar joints should account for the same nominal expansion difference [S3]. C52100’s higher strength does not remove the need to check fatigue loading, sliding speed, lubrication, heat rejection, and galling against the actual service condition [S7][S8].

Standards and purchasing controls

ASTM B139/B139M-12(2017), titled Phosphor Bronze Rod, Bar, and Shapes, establishes composition limits for C51000, C52100, and C54400, among other grades [S9]. C51000 also has the aerospace designation AMS 4625, whose nominal composition is approximately 95% copper, 5% tin, and 0.03–0.35% phosphorus [S4]. For aerospace, medical, or other controlled applications, require the exact material and process specification rather than accepting UNS designation alone.

Record the UNS grade, product form, temper, dimensions, applicable ASTM or other governing specification, mechanical-property minimums, surface condition, and any lead-restriction requirement on the purchase order. ASTM B139/B139M-12(2017) is the cited composition reference for all three grades, while AMS 4625 applies to C51000 and alloy F468 covers C51000 fasteners [S6][S9]. This converts a broad alloy name into a specification that a supplier can inspect and a purchaser can audit.

For a final audit, compare the certificate analysis against the applicable composition table, confirm the temper and tensile-strength requirement, and verify that C54400 is permitted by the finished product’s service and regulatory constraints. These checks distinguish a correct material selection from an incomplete purchase specification.

Frequently asked questions

Which wrought tin bronze grade should be specified for a fatigue-critical spring, and what temper should be stated?

Specify C51000 and state the required temper because its published tensile strength ranges from about 46,000–50,000 psi annealed to 70,000 psi half hard, 84,000 psi hard, and 96,000 psi extra hard. C51000 is the wrought spring grade, is covered by alloy F468 for fasteners, and is used for springs and contacts.

When is C52100 preferable to C51000 for bushings, gears, and heavy-load wear parts?

Choose C52100 when greater tensile strength and wear resistance are the dominant requirements. It is the approximately 8% tin member of the group and exceeds C51000 in strength, making it suitable for bushings, thrust washers, gears, and heavy-load, low-speed wear components.

What composition limits distinguish leaded C54400 from C51000 for procurement?

C54400 contains 85.4–91.5% copper, 3.5–4.5% tin, 3.5–4.5% lead, 1.5–4.5% zinc, and 0.010–0.5% phosphorus. C51000 has a nominal composition of approximately 95% copper, 5% tin, and 0.03–0.35% phosphorus.

How much does C54400 improve machining productivity, and what restriction applies to its selection?

C54400 has a machinability rating of 80. Its 3.5–4.5% lead content can restrict use in public-health, plumbing, food-contact, environmental, or customer-specific applications, so it should not be selected automatically.

9 sources
  1. Phosphor Bronze Alloy C51000 C52100 Copper Tin Alloy
  2. Extruded or cast and drawn product list
  3. C51000 Bronze vs. C54400 Bronze
  4. The Versatile Phosphor Bronze for Electrical and Industrial ... (Dec 31, 2025)
  5. Bronze vs. Phosphor Bronze: What's the Difference? (Jun 14, 2026)
  6. Phosphor Bronze C51000 / C54400
  7. C52100 - Copper Alloys
  8. Phosphor Bronze – Properties, Grades, Applications ... (Feb 11, 2026)
  9. ASTM B139/B139M-12(2017) - Phosphor Bronze Rod, Bar, ...

Need to source matching manufacturers or get a quote?

SpecForge connects industrial buyers with verified manufacturers. Submit your requirement and we will route it to matched suppliers.

Submit RFQ now →
Ask SpecForge AI