REQUEST FOR QUOTE → Request a quote
SpecForge Editorial Team

C90300 vs C92200 Tin Bronze for Valve Selection

Table of Contents
  1. Composition and material identity
  2. Strength, hardness, and machinability
  3. Pressure service and seawater exposure
  4. Cost, fabrication, and integration
  5. Application-by-application selection
  6. Failure modes and purchasing controls
  7. Decision matrix and procurement recommendation
C90300 vs C92200 Tin Bronze for Valve Selection

C90300 Navy G and C92200 Navy M differ materially: C90300 is lead-free and has the clearer published strength advantage, while C92200 contains 1.5% lead and machines more readily [S3][S5][S7].

Use C90300 for seawater, pressure-retaining, naval, or lead-restricted valve castings; use C92200 where free machining and established leaded-bronze procurement matter more [S1][S2][S5].

Composition and material identity

C90300 is the lead-free Navy G tin bronze, identified as SAE 620 and associated with the continuous-cast specification ASTM B505 [S1][S2][S4]. C90300 is also associated with QQ-C-390 for naval and federal castings, with Type III continuous-cast material specified for dense, pressure-tight valve bodies and pump housings [S2].

C92200 is the leaded Navy M tin bronze, also identified as C922, with 1.5% lead [S5][S6][S7].

The selection should therefore be made against the actual UNS designation, product form, applicable material specification, and foundry process. “Navy M” and “Navy G” labels are not sufficient procurement descriptions by themselves, especially when continuous-cast bar and finished valve castings can have different acceptance requirements [S1][S2][S3].

Strength, hardness, and machinability

C92200 is selected when machining productivity and dimensional control justify a leaded alloy. Its machinability is listed separately from the C90300 value on the Navy M technical data sheet, but the supplied material does not provide a directly comparable minimum tensile strength, yield strength, elongation, or hardness set [S3].

C90300 therefore has the clearer published structural advantage in the available data. The engineering trade is direct: C90300 offers stronger, lead-free casting performance but is described as harder to machine, while C92200 is the more machining-oriented alloy for production of complex valve parts and fittings [S1][S3][S5].

Pressure service and seawater exposure

C90300 is specifically identified for naval valves, pump components, heavy-duty marine fittings, bearings, bushings, steam fittings, and valve components [S1][S2][S9]. Type III continuous-cast C90300 is described as having a denser grain structure than sand casting, supporting pressure tightness in valve bodies and pump casings [S2].

C90300 has approximately 8% tin and no lead, compared with approximately 6% tin and 1.5% lead in C92200; the higher tin and lead-free composition provide C90300 with better corrosion resistance and strength, but reduced machinability [S7]. C90300 also has strong resistance to dezincification, an important consideration for seawater-exposed valve components [S1].

C92200 is well known for its industrial applications, while C90300 is lead-free and therefore distinct from C92200, which contains 1.5% lead [S6][S7]. For a seawater system with pressure-retaining castings, C90300 is the more defensible default.

Cost, fabrication, and integration

C90300 is described as having reduced machinability compared with C92200 [S7]. That machining trade can offset the higher material or casting cost of a lead-free alloy, but no cost figures are available in the supplied research and procurement should be based on actual foundry quotes.

C90300 can be used for welding, brazing, and soldering [S4]. This gives C90300 an advantage when valve-body repair, field joining, or complex assembly is part of the fabrication plan [S2].

C92200 may remain the lower-integration-effort choice for a shop already machining leaded Navy M stock with stable feeds, speeds, and tooling. C90300 is lead-free, has excellent corrosion resistance in seawater, can be used for welding, brazing, and soldering, and is associated with structural integrity under pressure [S2][S4].

Application-by-application selection

For naval seawater isolation valves, pump casings, and valves exposed to dezincification risk, select C90300 when the drawing permits ASTM B505 material and the pressure design can be supported by the casting supplier.

Its 1.5% lead content and favorable machinability are established commercial features, while C90300 is the stronger and more corrosion-resistant but less machinable alternative [S1][S3][S5][S7].

For potable-water service, C90300 is the more suitable of these two alloys because it is lead-free and meets NSF potable-water requirements [S4]. For a valve where lead is prohibited by the project specification, accepted code, or customer material restriction, C92200 should be rejected regardless of its machining economics [S4][S5].

Failure modes and purchasing controls

The principal C92200 failure risk is not a lack of industrial validity, but incompatibility with lead-sensitive service. It also requires separate control for machinability, weldability, and corrosion performance because a free-cutting modification does not establish the same environmental or fabrication performance as Navy G [S3][S4][S7].

The principal C90300 risks are harder machining, higher material cost, and the need to verify the correct casting condition and product form. Continuous-cast Type III stock cannot be assumed interchangeable with sand-cast C90300 without reviewing the applicable drawing and ASTM B505 requirements [S1][S2].

Specify UNS C90300 or UNS C92200, the product form, ASTM or federal specification, dimensional and pressure requirements, heat treatment or casting condition, repair method, and applicable service restrictions. For C90300 procurement, request mill test reports covering chemistry and mechanical properties; ASTM B505 covers continuous-cast copper-alloy material, while Type III continuous casting is associated with the C90300 and QQ-C-390 material context [S1][S2].

Decision matrix and procurement recommendation

Across the four controlling criteria, C90300 wins on documented strength, lead-free compliance, and seawater corrosion performance, while C92200 wins on machining productivity and established leaded-valve processing [S1][S3][S5][S7]. C90300 is rated at 45 ksi tensile strength and 70 Brinell hardness with 42% machinability; C92200 is defined by 1.5% lead, with exact comparable strength and hardness values not supplied in the research [S1][S3][S5][S7].

Specify C90300 Navy G for pressure-critical seawater valves, naval systems, potable-water components, weldable assemblies, and applications requiring a lead-free pressure-retaining bronze. Specify C92200 Navy M for leaded valve components where machining cost and production rate dominate and the service specification permits lead. For either alloy, the purchase specification should control the grade because the trade names alone do not define chemistry, casting method, acceptance criteria, or service suitability.

The next procurement check is the valve drawing and material certificate: confirm UNS number, ASTM B505 or other governing product specification, casting condition, pressure class, and lead and seawater service restrictions before approving either Navy G or Navy M.

Frequently asked questions

Which bronze alloy should be specified for a seawater pressure-retaining valve casting?

Specify C90300 Navy G for seawater and pressure-retaining valve castings because it is lead-free, provides excellent corrosion resistance in seawater, and is engineered for structural integrity under pressure [S2][S4].

What ASTM material specification applies to continuous-cast C90300 valve castings?

ASTM B505 is the continuous-cast specification associated with C90300 Navy G, which is also identified as SAE 620, and Type III continuous casting produces a denser grain structure and internal soundness for critical fluid-handling systems [S2][S4].

How much lead is permitted in C92200 Navy M, and what fabrication advantage does it provide?

C92200 Navy M, also identified as C922, contains 1.5% lead and has reduced machinability compared with C90300 [S5][S6][S7].

When should C92200 Navy M be rejected despite its machining productivity?

Reject C92200 when the project specification, applicable code, or customer restriction prohibits lead, particularly for potable-water service. Although it is established for valves and fittings, its 7% to 15% lead content makes it unsuitable where lead-free compliance controls the design.

9 sources
  1. Anchor Bronze & Metals, Inc.
  2. C90300 Tin Bronze (Navy G) | ASTM B505 & QQ-C-390 ...
  3. C92200 Navy M Tin Bronze Technical Data Sheet
  4. C90300 Navy G Bronze Now Available Online (Nov 28, 2018)
  5. C92200 Alloy, C922 Leaded tin bronze
  6. C92200 Leaded Tin Bronze "Navy M"
  7. Navy G Bronze Alloy UNS C90300
  8. C90300 Tin Bronze, Lead Free "Navy G" Round
  9. C90300 Tin Bronze | Technical Specifications | DBM

Need to source matching manufacturers or get a quote?

SpecForge connects industrial buyers with verified manufacturers. Submit your requirement and we will route it to matched suppliers.

Submit RFQ now →
Ask SpecForge AI