REQUEST FOR QUOTE → Request a quote
SpecForge Editorial Team

Engineering Plastic Tensile Modulus Compared by Resin

Table of Contents
  1. Tensile Modulus Is a Stiffness Metric, Not a Failure Metric
  2. Commodity and Sheet Resins: Modulus Alone Is Misleading
  3. High-Performance Thermoplastics: Modulus and Ductility Separate
  4. Comparison Across Four Decision Criteria
  5. Temperature, Chemicals, and Creep Change the Ranking
  6. How to Specify and Verify the Resin
Engineering Plastic Tensile Modulus Compared by Resin

Unreinforced engineering-plastic tensile moduli range from about 0.75 GPa for PTFE to nearly 6 GPa for PBI, while PEEK, PAI, PPS, and PEEK family grades cluster near 4 GPa [S4].

The choice is not simply stiffest versus softest: tensile modulus controls elastic deflection, while tensile strength, elongation, temperature, chemicals, and reinforcement determine whether a component can survive service [S1][S2][S4].

Tensile Modulus Is a Stiffness Metric, Not a Failure Metric

Tensile modulus is the slope of the stress-strain curve in the elastic region, expressed in MPa or GPa. ISO 527 is the principal tensile test cited for plastic specimens, producing tensile stress in MPa or N/mm², elongation in percent, and the stress-to-strain ratio used to determine Young’s modulus [S4].

Tensile strength answers a different question. It identifies the stress reached before yielding or fracture, while tensile modulus indicates how much strain develops under elastic loading. Fasteners, clips, tabs, lips, and thin sections can fail in tension even when a panel is sufficiently stiff in bending [S1][S2].

For sheet products, flexural modulus, tensile strength, elongation, and notched impact resistance are key properties to evaluate when selecting a thermoforming plastic [S1]. A complete selection record should keep these four properties separate instead of treating “strength” as one undifferentiated rating.

Commodity and Sheet Resins: Modulus Alone Is Misleading

In the cited comparison of eight common thermoforming plastics, rigid PVC and Kydex T are the stiffest, followed by PC, ABS, HIPS, and PETG, while HDPE and PP are the most flexible [S1]. These values make the sheet families look similar in bending even though their tensile behavior differs sharply.

The cited comparison reports that PC is strongest in tension, followed by PETG, then ABS and Kydex T, and identifies PC, Kydex T, and PP copolymer as combining high notched Izod impact resistance with high elongation [S1].

The cited comparison identifies PP and HDPE as among the most flexible sheet plastics and HIPS as relatively stiff [S1].

For general thermoformed hardware, ABS is often the practical starting point because ribs, flanges, and gauge can correct perceived flexure more economically than moving to a higher-modulus resin [S1]. This makes engineering plastic selection a geometry-and-load exercise, not a resin-only ranking.

High-Performance Thermoplastics: Modulus and Ductility Separate

engineering plastic tensile modulus comparison across resin families - High-Performance Thermoplastics: Modulus and Ductility Separate
engineering plastic tensile modulus comparison across resin families - High-Performance Thermoplastics: Modulus and Ductility Separate

Tensile properties such as tensile strength, elongation, and tensile modulus characterize the mechanical behavior of unreinforced and reinforced high-performance polymers, with ISO 527 identified as the most used tensile-test standard [S4]. The modulus spread is approximately eightfold, but PTFE accepts large deformation while PBI remains brittle and load-sensitive.

PEEK and polysulfone combine relatively high stiffness with the tough, hard behavior typical of engineering thermoplastets, while PAI offers high strength with useful elasticity [S4]. These values suit dimensionally stable components better than a soft, highly extensible polymer when creep, alignment, or surface finish matters.

Reinforcement changes the comparison. Glass or carbon fibers increase tensile strength and reduce elongation, and even reinforced PTFE remains below the tensile-strength level of reinforced high-performance polymers in the reviewed data [S4]. For an application involving stiffness, load capacity, and thermal duty, PEEK, PAI, and PPS should be compared as specific grades, not as family names.

Comparison Across Four Decision Criteria

Sheet thermosetting and impact-capable grades answer a different design question. In the cited comparison, rigid PVC and Kydex T are the stiffest sheet plastics, PC is strongest in tension and combines high notched Izod impact resistance with high elongation, and PP copolymer combines high notched Izod impact resistance with high elongation [S1].

For semi-crystalline molded materials, POM is a distinct option because it combines high stiffness with low friction and predictable dimensional behavior. It should not be compared with unreinforced amorphous sheet resin using one generic modulus number, since grade, orientation, reinforcement, moisture conditioning, and test geometry can shift the result.

Temperature, Chemicals, and Creep Change the Ranking

engineering plastic tensile modulus comparison across resin families - Temperature, Chemicals, and Creep Change the Ranking
engineering plastic tensile modulus comparison across resin families - Temperature, Chemicals, and Creep Change the Ranking

Room-temperature modulus is only one design input. High-temperature comparisons in the reviewed engineering-polymer data extend to 150 °C and 200 °C, confirming that tensile properties must be evaluated at the service temperature rather than assumed constant [S4]. A material with 4 GPa modulus at 23 °C may lose appreciable stiffness under sustained heat.

Chemical compatibility must be screened before mechanical performance. Solvents can cause swelling, oxidizers can embrittle polymer chains, hot water and steam can hydrolyze nylons, polyesters, and polycarbonate, and environmental stress cracking can split a chemically compatible resin under applied or residual stress [S5]. The relevant variables are the exact medium, concentration, temperature, contamination, cleaning cycle, and sustained load [S5].

Temperature limits further constrain the candidate list. PP is generally considered around 80–100 °C for many chemical services; PVDF extends to about 140 °C in selected media; PEEK can serve to about 250 °C; PTFE and PFA reach roughly 260 °C; and FEP reaches about 200 °C [S5]. For repeated thermal exposure, the engineering-plastic selection guide for steam sterilization provides a separate service-life framework rather than relying on tensile modulus alone.

How to Specify and Verify the Resin

Request the tensile modulus for the exact grade, orientation, conditioning state, thickness, and test temperature. ISO 527 provides tensile stress and elongation data, while ASTM D638 is cited for tensile strength and ASTM D790 for flexural modulus [S1][S4]. Where stiffness controls a thin part, ISO 527 tensile modulus alone may not capture the actual deflection, so a stiffness calculation using the relevant section modulus and boundary conditions remains necessary.

Use tensile strength to size stressed sections and tensile modulus to control elastic deflection. Then check elongation for the intended failure mode: elongation below roughly 5% is characteristic of brittle behavior, while much higher values indicate ductility, as shown by PBI at about 3% and PTFE above 250% [S1][S4].

For chemical service, request compatibility evidence for the specific concentration and temperature rather than treating a general “chemical resistant” label as sufficient [S5]. For loaded or fiber-reinforced parts, record the reinforcement type and weight percentage because glass and carbon reinforcement increase tensile strength while reducing elongation [S4].

The practical trackable signal is a material data sheet containing at least ISO 527 tensile modulus, tensile strength, elongation, test temperature, conditioning state, specimen designation, and reinforcement content. Comparing those fields across synthetic resin families gives a defensible selection and exposes where a supplier table is using unlike test conditions.

Frequently asked questions

What unreinforced engineering-plastic tensile modulus range should I use for initial resin screening?

Verify the specific grade at the service temperature before final selection.

Which standard test determines tensile modulus for engineering plastics?

ISO 527 is the principal tensile-test standard cited for plastic specimens and provides the stress-to-strain relationship used to determine Young’s modulus. Tensile modulus is reported in MPa or GPa, while tensile strength and elongation must be recorded separately.

When should flexural modulus be considered instead of tensile modulus for a sheet component?

Consider ASTM D790 flexural modulus when visible deflection of sheet, panels, or formed sections is the controlling behavior. For thin tabs, clips, lips, or fasteners, tensile strength may be more relevant even when the larger panel is sufficiently stiff in bending.

How do PEEK, PAI, and PPS compare for an unreinforced high-performance component?

Compare specific grades for tensile strength, elongation, temperature, chemicals, creep, and reinforcement rather than treating them as interchangeable.

7 sources
  1. Picking a Thermoforming Plastic by Tensile Strength (Nov 20, 2025)
  2. Tensile Strength vs Flexural Modulus: Which Plastic Metric ...
  3. Tensile Property Testing of Plastics
  4. Design Properties for Engineers: Tensile Properties of High ... (Jun 8, 2020)
  5. Blog
  6. Technical Plastic Material Data & Datasheets
  7. Synthetic Polymer Resin Vs Polyester: Tensile Strength ... (Jul 10, 2026)

Need to source matching manufacturers or get a quote?

SpecForge connects industrial buyers with verified manufacturers. Submit your requirement and we will route it to matched suppliers.

Submit RFQ now →
Ask SpecForge AI