REQUEST FOR QUOTE → Request a quote
SpecForge Editorial Team

Load Pin vs Tension Link for Crane Sheave Force Measurement

Table of Contents
  1. How a Load Pin Reads Sheave Force
  2. How a Tension Link Reads Sheave Force
  3. Decision Matrix: Load Pin vs Tension Link at the Sheave
  4. Sheave Wrap Angle: The Hidden Failure Mode
  5. Materials, Safety Factors, and Output Options
  6. When to Choose a Different Sensor Entirely
  7. Selection Rules in One Pass
Load Pin vs Tension Link for Crane Sheave Force Measurement

The decision between a load pin and a tension link for sheave force measurement is driven by where the load sits in the load path: a load pin becomes the sheave axle itself, while a tension link hangs in line with the rope and carries the full pull through its body [S1].

Both sensor families resolve force through bonded strain gauges on a Wheatstone bridge, but they differ in headroom cost, integration effort, and whether they can stay on the machine permanently. The choice typically narrows to two or three candidates once the measurement point is locked in [S1].

How a Load Pin Reads Sheave Force

A load pin is a shaft instrumented with internal strain gauges, designed to replace a clevis, sheave, equalizer, or pivot pin in an existing load path [S2]. The exterior carries two grooves that define the measured section; the sheave applies force on the middle of the pin and the fixed support reacts on the opposite side, so the gauges see a clean double-shear signal [S2][S7].

Because the sensor physically becomes the sheave axle, it consumes zero additional headroom, which is the strongest argument for permanent crane monitoring where every millimetre of lift matters [S1]. Trade-off: each pin is custom engineered to the pin it replaces, so there is no shelf-stock option, and the standard manufacturing envelope spans 0.5 t up to 1500 t and above [S1][S5].

How a Tension Link Reads Sheave Force

A tension load cell dynamometer sits in line with the rope and carries the full tension directly through the sensor body, which makes it the workhorse for proof loading, load testing, and any application where the lift is a straight pull [S1].

Tension links are also the usual starting point for custom work when the geometry is unusual, since the body shape can be machined around the load path instead of dropped into a fixed pin location [S1]. They bolt into the rigging at a shackle or hook connection, so installation and removal are quick, but every installation adds measurable headroom and a hard-link component in series with the sheave. For non-straight-pull applications such as crane sheaves with changing wrap angle, a standard shear pin only measures the resultant force, not true line tension, unless it has an internal amplifier that resolves both load and wrap angle [S5].

Decision Matrix: Load Pin vs Tension Link at the Sheave

Four criteria separate the two sensor families on a real crane sheave installation. Capacity: load pins cover 0.5 t to over 1500 t as a single custom part, while stock tension links and load shackles from one major supplier span 6.5 t to 85 t [S1][S5]. Headroom cost: a load pin takes zero extra space because it replaces an existing pin; a tension link adds the full link length plus end fittings in series with the rope [S1][S2].

Permanence: load pins are designed to be permanently installed in a sheave, pulley, or crane system to consistently monitor vertical or horizontal tension, while tension links are typically moved between lifts [S2]. Lead time: load pins are custom engineered, so they carry weeks of design and manufacture; tension links and load shackles are commonly stocked, with the load shackle format especially attractive to riggers because it requires no new procedure to learn [S1].

Sheave Wrap Angle: The Hidden Failure Mode

A standard shear-pin load cell only produces an accurate reading when load is applied in one plane, and on a sheave that means it measures the resultant force on the axle, not the true line tension in the rope [S5]. When wrap angle shifts, the resultant force shifts with it, and a basic load pin will drift off the true line tension value as a result [S5].

One documented workaround, the DLM Line Tension Load Pin (LT-LP d), uses an internal amplifier that senses both the resultant force and the wrap angle to compute true line tension, then outputs a 4-20 mA signal scaled to safe working load across a 40° to 130° wrap range [S5]. In a real installation, this matters: existing steel pins in the rope sheaves were replaced by load pins rated for 10 kN with safety factor S=3, IP65 protection, and an integrated amplifier in the control system, where line tension directly drives safety decisions [S8].

Materials, Safety Factors, and Output Options

Industrial load pins are typically machined from 17-4 PH stainless steel, which gives high strength plus corrosion resistance for marine, port, and outdoor service; the DLM LT-LP d uses 17-4PH H1150 + 1150 stainless and is rated for operating temperatures from -40 °C to +80 °C with subsea versions pressure-tested to 300 bar [S5]. Rice Lake's MSI line uses the same 17-4 stainless base with a 5:1 ultimate safety factor, and exposes gauges only via an internal bore, which keeps the strain gauges shielded from shock, moisture, and contamination [S2][S4].

Output options are a shared ecosystem between the two sensor families: 4-20 mA, 0-5 VDC, 0-10 VDC, and RS485 Modbus are all common, with the DLM line-tension pin offering both a 3-wire 4-20 mA and an RS485 Modbus variant on 12-30 VDC input [S2][S5]. For permanent sheave monitoring, a 4-20 mA loop is typically the cleanest path into a PLC or indicator; for a load shackle acting as a sheave-line force sensor, a wireless option is widely available to avoid a cable wrap on the sheave [S1]. For more on how that analog signal terminates at a display, see the load cell to indicator signal path reference.

When to Choose a Different Sensor Entirely

A load pin and a tension link are not the only options, and forcing them into the wrong measurement point is a common cause of project failure. A running line tensiometer clamps onto the wire rope and reads rope tension by deflection without entering the load path at all, which is the right answer on a machine that cannot be taken out of service, but it measures rope tension rather than hook load, and on a reeved system those two values are related, not equal [S1].

A hanging crane scale below the hook is the right call when all the user needs is a weight readout, with no PLC integration, no data logging, and no overload protection requirement; the absence of integration work is itself a major time saving [S1]. For a baseline overview of load cell architecture, including how bonded strain gauges on a Wheatstone bridge form the sensing element inside both load pins and tension links, refer to the encyclopedia entry.

Selection Rules in One Pass

Specify a load pin when the measurement point is a sheave or equalizer pin on a permanent crane installation, headroom is constrained, and the engineering budget can absorb a custom part with several weeks of lead time; expect 17-4 PH stainless construction, double-shear strain gauge layout, and a standard 4-20 mA or Modbus output [S1][S2][S5]. Specify a tension link when the lift is a straight pull, the sensor must move between jobs, and off-the-shelf delivery matters more than zero headroom gain; expect capacities in the 6.5 t to 85 t stock range from major suppliers, with shackle-form factors that riggers can deploy without retraining [S1].

For a force gauge or hand-held readout at the sheave, the same 4-20 mA loop will drive a portable indicator; for a crane scale hung below the hook, a digital load cell output will drive a wireless display. Verify the wrap angle behaviour of any sheave-mounted pin before purchase, and confirm the safety factor, IP rating, and proof-load certificate against the relevant national traceable standard for the rated capacity [S5][S8].

Frequently asked questions

What capacity range should I expect for a custom load pin versus a stock tension link on a crane sheave?

Custom load pins are typically specified from 0.5 t up to 1500 t and above as a single engineered part, while off-the-shelf tension links and load shackles from one major supplier span 6.5 t to 85 t. For capacities above 85 t on a quick lead time, a custom load pin is usually the only option.

How does sheave wrap angle affect load pin accuracy, and what fixes it?

A standard shear-pin load cell only measures the resultant force on the axle, so as wrap angle changes the reading drifts away from true line tension. The DLM LT-LP d line tension load pin solves this with an internal amplifier that senses both resultant force and wrap angle, outputting a 4-20 mA signal scaled to SWL over a 40° to 130° wrap range.

What headroom penalty does a tension link add compared with a load pin on a sheave?

A load pin consumes zero extra headroom because it physically replaces the existing sheave axle. A tension link adds its full body length plus the end fittings in series with the rope, which can be significant on cranes where every millimetre of lift height matters.

What materials, safety factors, and outputs are standard for industrial sheave load pins?

Industrial load pins are typically machined from 17-4 PH stainless steel (e.g., DLM LT-LP d uses 17-4PH H1150 + 1150), with Rice Lake MSI using the same base at a 5:1 ultimate safety factor. Standard outputs across both families include 4-20 mA, 0-5 VDC, 0-10 VDC, and RS485 Modbus, and the DLM line-tension pin runs on 12-30 VDC input with an operating range of -40 °C to +80 °C.

8 sources
  1. Crane Load Cells: How to Choose the Right Sensor (Aug 13, 2026)
  2. What Is a Load Pin?
  3. Load Pins 101 (Jan 12, 2021)
  4. Load Pins: Types, Applications & Benefits
  5. Line Tension Load Pin, LT-LP d
  6. Everything You Need to Know About Load cells (Jul 6, 2021)
  7. How does a load pin work
  8. Load pins: measuring rope forces on sheaves (Jul 23, 2026)

Need to source matching manufacturers or get a quote?

SpecForge connects industrial buyers with verified manufacturers. Submit your requirement and we will route it to matched suppliers.

Submit RFQ now →
Ask SpecForge AI