REQUEST FOR QUOTE → Request a quote
SpecForge Editorial Team

Select Accelerometer Sensitivity for Slow, Low-Level Machines

Table of Contents
  1. Set the selection target from machine speed and vibration level
  2. Compare sensitivity against range, resolution, and noise
  3. Confirm that acceleration is the required measurement variable
  4. Use 500 mV/g for slow machines, not as a universal rule
  5. Check measurement type, installation, and electronics together
  6. Apply the limits of high-sensitivity charge accelerometers
Select Accelerometer Sensitivity for Slow, Low-Level Machines

For a low-speed machine with low vibration output, consider a 500 mV/g or 1000 mV/g accelerometer, using low-noise, high-gain amplification to improve the signal-to-noise ratio.

Sensor selection should consider signal level, bandwidth, saturation margin, mounting, the required measurement variable, and factors beyond sensitivity alone.

Set the selection target from machine speed and vibration level

Low-frequency measurements are used in industries such as hydro power, pulp and paper, metal, mining, cement, water treatment, and petrochemical, including applications involving rolls, mills, rotary kilns, agitators, pelletizers, extruders, and other slow-speed machinery. At a given excitation frequency, displacement, velocity, and acceleration have a fixed relationship, and low-frequency acceleration signals can be small.

High-sensitivity accelerometers rated at 500 mV/g or 1000 mV/g are options for low-speed applications, while sensor selection should account for the complete signal chain and the risk of excessive noise or signal clipping. These are starting points, not substitutes for checking the actual waveform and noise floor.

For a machine in the 0.1–10 Hz range, establish the expected acceleration spectrum, estimate the signal at the analyzer input, and then confirm that the selected sensor has enough output above system noise without approaching its full-scale limit. Higher sensitivity is not automatically better because it reduces available amplitude range [S1][S2].

Compare sensitivity against range, resolution, and noise

This creates a direct trade-off: the more sensitive sensor produces a larger voltage for a small acceleration, improving signal-to-noise ratio, but its lower full-scale range leaves less headroom for startup, impact, imbalance, or transient events [S1][S7]. For low-speed or low-level applications, consider a 500 mV/g or 1000 mV/g accelerometer.

Noise must be evaluated at the measurement bandwidth. A sensor that appears adequate across a broad spectrum can still be unsuitable if its own noise dominates the 0.1–10 Hz band. Wilcoxon identifies low electronic noise in both sensor and monitoring instrument as the primary objective for this work [S2].

Confirm that acceleration is the required measurement variable

selecting sensitivity for a low-amplitude low-speed machine - Confirm that acceleration is the required measurement variable
selecting sensitivity for a low-amplitude low-speed machine - Confirm that acceleration is the required measurement variable

Low-frequency machinery is often specified in velocity, typically in inches per second, or displacement, typically in mils peak-to-peak, because those variables can be more informative than raw acceleration at low frequency [S2]. Accelerometers can be integrated or processed into velocity and displacement, but the conversion does not remove the need to select the correct sensor [S2][S3].

A moving-coil velocity sensor can have an inherent advantage for low-frequency measurements.

For broad amplitude and frequency coverage, a properly selected piezoelectric accelerometer remains versatile and can be integrated to velocity or displacement [S2]. A more detailed comparison of these approaches is available in Piezoelectric Accelerometer vs Velocity Sensor for Low-Frequency Machine Vibration. Selection should therefore begin with the required engineering quantity: use proximity measurement for true position or shaft-relative displacement, and use a seismic sensor when the objective is casing or structural vibration [S3].

Use 500 mV/g for slow machines, not as a universal rule

A 500 mV/g accelerometer is a defensible starting point for slow-speed, low-amplitude monitoring, but the selected unit still needs adequate low-frequency response and noise performance [S3][S4].

For machines below about 600 rpm, the selection should be verified against three values: the expected acceleration in g at the fault frequencies, the analyzer or controller input noise in the same frequency band, and the largest credible transient amplitude. If the expected level is below the system noise, increase sensor sensitivity or add low-noise, high-gain amplification [S1][S7].

A low-noise, high-gain preamplifier can be used to increase sensitivity when measuring low-level signals. That option is useful when changing the sensor would create undesirable mounting or range constraints, but added gain also increases the risk of amplifying noise or driving the downstream input beyond its usable range [S7].

Check measurement type, installation, and electronics together

selecting sensitivity for a low-amplitude low-speed machine - Check measurement type, installation, and electronics together
selecting sensitivity for a low-amplitude low-speed machine - Check measurement type, installation, and electronics together

Mounting can determine whether a high-sensitivity sensor produces usable data. Poor bonding, rocking, inadequate contact, or mounting on a moving surface can suppress low-frequency response or introduce distortion [S2][S4]. Sensor settling time, instrument configuration, processing time, environmental noise, and nearby electrical or mechanical interference also require review for low-frequency work [S2].

For an IEPE chain, the sensor output must remain compatible with the input bias voltage, power, cable length, and signal-conditioning range. In a vibration-control system, a typical 24-bit ADC may use a ±10 V range, while selectable signal-conditioning gains of 0.1×, 0.3×, 1×, 3×, 10×, 30×, and 100× can provide a 1000:1 adjustment range [S5].

The sensor, conditioner, and ADC must be sized together. A 100 pC/g charge accelerometer produces ten times the charge of a 10 pC/g unit at the same acceleration, but the resulting voltage also depends on the charge-amplifier conversion and subsequent signal gain [S5]. For control applications, clipping at any stage can invalidate the test even if the mechanical input is within the accelerometer’s nominal range [S5].

Apply the limits of high-sensitivity charge accelerometers

High sensitivity is not restricted to voltage-output IEPE devices. Charge-output accelerometers can be specified in pC/g, and a 100 pC/g sensor generates 100 pC for each g of acceleration, compared with 10 pC at 1 g for a 10 pC/g unit [S5]. This can be useful in low-amplitude installations with compatible low-noise charge amplifiers.

The nominal sensitivity also does not describe the complete usable bandwidth, noise level, mounting resonance, temperature response, or environmental rating.

For general low-frequency condition monitoring, reject a candidate sensor if it lacks a stated response at the frequencies of interest, if its self-noise is not characterized, or if its mounting method cannot be repeated consistently. The correct specification is not simply the largest mV/g number; it is the sensor and signal chain that retain an accurate, unclipped signal across the required 0.1–10 Hz band or the applicable fault-frequency range [S1][S2].

Before issuing a purchase specification, record the machine speed, fault frequencies, expected acceleration and velocity levels, maximum credible shock, analyzer input range, and mounting surface. Use 500 mV/g as the initial sensitivity for a typical machine below about 600 rpm, then accept it only after a low-noise signal calculation and an installation trial confirm adequate margin above noise and below saturation.

8 sources
  1. Choosing Accelerometer Sensitivity: 100 vs 500 mV/g (3 days ago)
  2. Low frequency machinery monitoring: measurement considerations
  3. Sensor Selection Criteria for Low-Frequency Measurements – Part 2
  4. Slow Speed and Low Frequency Vibration Measurement (Feb 29, 2020)
  5. Transducer Sensitivity Selection for Vibration Control
  6. Low-Speed Machines Vibration Monitoring - Orbit Institute (Mar 29, 2024)
  7. How to Increase Sensitivity When Measuring Low-Level Signals?
  8. Which Sensitivity is best - Vibration Analysis & Machinery Diagnostics ... (Oct 18, 2022)

Need to source matching manufacturers or get a quote?

SpecForge connects industrial buyers with verified manufacturers. Submit your requirement and we will route it to matched suppliers.

Submit RFQ now →
Ask SpecForge AI