REQUEST FOR QUOTE → Request a quote
SpecForge Editorial Team

Static, Couple and Dynamic Unbalance for Rotors

Table of Contents
  1. Static Unbalance: One Heavy Spot and One Plane
  2. Couple Unbalance: Equal Opposed Masses
  3. Dynamic Unbalance: Static and Couple Combined
  4. Disc Versus Long Rotor: Decision Matrix
  5. Limits, Severity and Test Acceptance
  6. Application Selection by Equipment
  7. Measurement Procedure and Correction Record
Static, Couple and Dynamic Unbalance for Rotors

Static unbalance is corrected in one plane, while couple and dynamic unbalance generally require two correction planes.

Rotor geometry and correction-plane count are key considerations, while flexible rotors require special methods rather than ordinary two-plane balancing.

Static Unbalance: One Heavy Spot and One Plane

Static unbalance occurs when the rotor center of mass is offset from the rotational axis, while the mass axis remains parallel to that axis [S1][S3]. This condition is visible at rest: a disc placed on low-friction knife edges rotates until its heavy spot settles at the bottom [S2].

The balancing quantity is mass multiplied by radius, expressed in g·mm. A 1 g mass at 100 mm radius produces the same unbalance as 10 g at 10 mm radius [S2]. Correction normally adds or removes weight 180° opposite the heavy spot in a single correction plane [S3][S4].

Static balancing corrects unbalance in one plane and suits thin, disc-shaped parts. A practical geometry threshold is L/D below 0.25, with some guidance extending single-plane practice below 0.5 [S4].

Couple Unbalance: Equal Opposed Masses

Couple unbalance represents two equal heavy spots located in different axial planes and 180° apart, so their centrifugal forces form a couple rather than a single net radial force [S4]. The rotor can appear balanced on knife edges because its center of mass remains on the axis, but rotation produces an end-to-end rocking or wobbling action [S2][S3].

Two correction planes are required because one weight cannot cancel two separated force vectors [S2][S5]. Couple unbalance is characteristic of long, slender shafts, cardan shafts, long axial-fan rotors, and elongated cylindrical rotors [S4][S5]. Couple unbalance can be present despite static balance and can cause a rotor to tilt or wobble.

Static balancing alone can remove the visible heavy spot while leaving the couple component untouched [S2]. For a long rotor, the engineering acceptance test should therefore include a running-speed correction or at least a verification capable of detecting couple unbalance, rather than relying on knife-edge behavior alone.

Dynamic Unbalance: Static and Couple Combined

static vs couple vs dynamic unbalance explained with a disc and a long rotor - Dynamic Unbalance: Static and Couple Combined
static vs couple vs dynamic unbalance explained with a disc and a long rotor - Dynamic Unbalance: Static and Couple Combined

Dynamic unbalance combines the static and couple components, leaving the mass axis neither coincident with nor parallel to the rotational axis [S1][S5]. The resulting forces can produce radial vibration, axial motion, shaft tilt, or wobble, depending on rotor geometry and support arrangement [S1].

Dynamic balancing measures the rotor while rotating and determines the correction amount and angular position in two planes. Dynamic balancing is common for multistage pumps, crankshafts, and turbines.

The method differs from balancing on knife edges because it detects the rotating response rather than only the gravity-induced heavy-spot position [S2][S4]. It does not correct shaft runout, a poor shaft fit, or machine misalignment [S4].

Disc Versus Long Rotor: Decision Matrix

A thin disc normally has one correction plane when L/D is below 0.25 and is statically balanced with one correction weight [S4]. A rotor whose length is similar to or greater than its diameter normally needs dynamic balancing in two planes [S2]. The useful decision matrix is based on correction planes, length-to-diameter ratio, speed, and geometry defects.

For the article’s representative disc and long rotor, the decision is straightforward: use one-plane static balancing for a narrow, geometrically controlled disc, and two-plane dynamic balancing for a long shaft or rotor where axial separation permits a couple component.

Limits, Severity and Test Acceptance

static vs couple vs dynamic unbalance explained with a disc and a long rotor - Limits, Severity and Test Acceptance
static vs couple vs dynamic unbalance explained with a disc and a long rotor - Limits, Severity and Test Acceptance

Unbalance force rises with the square of rotational speed, so doubling speed quadruples the centrifugal force from the same residual unbalance [S2].

Residual unbalance is expressed as mass times radius, using g·mm or g·cm for metric work and gram-inches or ounce-inches for imperial work [S5].

For a long rotor, two-plane balancing addresses both net force and couple, but flexible rotors require methods beyond ordinary two-plane rigid-rotor balancing [S4].

Application Selection by Equipment

Static balancing suits thin, disc-shaped parts whose tolerance can be addressed in one correction plane.

Couple or dynamic balancing fits shafts, elongated rotors, crankshafts, turbines, multistage pumps, armatures, rolls, driveshafts, and cardan shafts [S2][S4][S5]. For these machines, a horizontal balancing machine can evaluate the separated correction planes more appropriately than a static check [S5].

Neither balancing method is a substitute for mechanical inspection. Verify shaft runout, hub fit, fastener security, and bearing alignment before accepting a residual balance result [S4]. Single-plane versus two-plane balancing for long rotors provides the direct geometry and correction-plane comparison for this decision.

Measurement Procedure and Correction Record

static vs couple vs dynamic unbalance explained with a disc and a long rotor - Measurement Procedure and Correction Record
static vs couple vs dynamic unbalance explained with a disc and a long rotor - Measurement Procedure and Correction Record

A production balancing record should identify the rotor, serial number, balancing machine, measurement speed, correction-plane locations, correction radius, applied or removed mass, angular positions, and final residual unbalance. The correction radius converts weight into the governing mass-radius quantity [S5].

For the disc, record the single correction angle and weight, then verify the rotor at the specified acceptance condition. For the long rotor, record both correction angles and weights because two separated unbalance vectors must be resolved into one another [S2]. Repeat measurements after correction and compare residual values with the applicable balance grade and machine acceptance criteria [S5].

The next verification point is measurable: confirm that the disc meets its specified residual-unbalance limit in one plane, and that the long rotor meets its two-plane residual limits at the specified measurement speed. If either value fails, repeat correction rather than tightening the machine supports to conceal the response.

Frequently asked questions

When is single-plane static balancing suitable for a rotor, based on its geometry?

Narrow discs with an L/D ratio below 0.25 need one correction plane, while rotors above an L/D ratio of 0.5 need two.

What unbalance values are equivalent when expressed as mass multiplied by radius?

A 1 g mass at a 100 mm radius produces the same unbalance as a 10 g mass at a 10 mm radius. Both represent 100 g·mm of residual unbalance.

How should a long shaft be tested if it appears balanced on knife edges?

Do not rely on knife-edge behavior alone, because a long shaft can be statically balanced while retaining a couple unbalance. Include a running-speed correction or another verification capable of detecting couple unbalance.

How much does residual unbalance force increase when rotational speed doubles?

Unbalance force rises with the square of rotational speed, so doubling the speed quadruples the centrifugal force from the same residual unbalance.

6 sources
  1. Balancing: Static, Coupled, and Dynamic
  2. Static vs Dynamic Balancing: Which You Need
  3. Static, Couple, and Dynamic Unbalance (Jan 7, 2022)
  4. Types of Unbalance: Static, Couple and Dynamic - Vibromera
  5. What is dynamic balancing
  6. Dynamic Balancing Vs. Static Balancing: Choosing The Right ... (Jun 26, 2026)

Need to source matching manufacturers or get a quote?

SpecForge connects industrial buyers with verified manufacturers. Submit your requirement and we will route it to matched suppliers.

Submit RFQ now →
Ask SpecForge AI