Fire-protection glazing in vision panels used in 60- and 90-minute temperature-rise doors located in exit enclosures and exit passageways cannot exceed 100 square inches, whether or not the building is fully sprinklered [S1].
The decision is not simply wired glass versus ceramic glass: confirm the door rating, glass area, impact-safety classification, heat-transfer requirements, and listed door assembly before specifying either product [S1][S2][S3].
Fire-Protective and Fire-Resistive Performance
Fire-protective wired and ceramic products contain flame and smoke but do not provide the same radiant-heat barrier as fire-resistive glazing [S1][S5][S6]. Fire-resistive glazing is intended to limit heat transfer as well as flame and smoke, making it the appropriate category for rated doors where temperature-rise criteria apply [S3][S4].
Fire-protective glass is most often ceramic, traditional wired glass, or specially tempered glass [S5]. Fire-resistive products include fire-resistive tempered units and multilaminate glass constructions that contain glass layers and fire-resistant interlayers [S4][S5]. Ceramic glass and fire-rated glass are not interchangeable labels: ceramic may have high heat resistance without carrying the same fire-door test listing as a listed vision panel [S5].
The tested fire door assembly controls the permitted lite size, glazing construction, frame, gasket, label, and installation details. A glass qualification by itself does not establish that an arbitrary field cut or lite kit is acceptable in the host door [S2].
Area Limits by Door Rating
For 20- and 45-minute fire doors, fire-protective glazing may be used up to the maximum size permitted by the tested assembly, including suitable tempered glass, filmed or laminated ceramic glass, and filmed wired glass [S3].
For 60- and 90-minute temperature-rise doors, fire-protective glazing is limited to 100 square inches when it is not fire-resistive [S1][S2][S3]. Fire-resistive glazing inhibits radiant heat in addition to containing the spread of fire and smoke [S5].
Where a specific tested assembly allows one, the glazing must be fire-resistive and limited to the size stated in that listing [S2].
Impact Safety Changes the Wired-Glass Decision

Door glazing is subject to CPSC Category I or Category II impact-safety requirements, and traditional wired glass may fail those requirements even when it has a fire-door listing [S3].
Glass ceramics do not have a wire mesh, and ceramic glass is described as stopping fire and impact injuries [S7][S8].
Impact protection is not a substitute for fire performance. A ceramic lite still needs the required fire rating, compatible framing, and assembly-specific listing; similarly, a wired lite must meet both the fire and impact provisions applicable to the opening [S2][S3].
Wired Glass or Ceramic: Decision Criteria
On visual clarity, traditional wired glass contains embedded metal mesh, while ceramic glass uses no wire mesh and presents a less institutional appearance [S7].
On radiant-heat control, neither ordinary wired nor ceramic fire-protective glass should be treated as a fire-resistive barrier [S1][S6]. Fire-resistive ceramic or multilaminate glazing should be selected when the door or code requires heat limitation, not merely flame and smoke containment [S3][S4].
On area flexibility, wired and ceramic fire-protective lites remain constrained to 100 square inches in 60- and 90-minute temperature-rise doors unless the specification changes to listed fire-resistive glazing [S1][S3].
Use traditional safety-rated wired glass where it has a valid fire and impact listing, the 100-square-inch limit applies, and budget and institutional appearance are acceptable. Use ceramic or another listed fire-protective product where clarity and impact performance are priorities, but retain the same size limits imposed by the fire classification [S2][S8].
Correct Assembly Selection and Documentation

Fire-rated door assemblies are tested with the glazing, lite-kit frame, hardware, door, and frame as a system. The glass and lite kit must be tested and listed for the specified rating [S2].
Do not substitute a ceramic hearth product for a listed fire-door lite without an assembly listing [S5].
Application Limits and Failure Modes
The most consequential specification error is treating a small fire-protective lite as equivalent to a large fire-resistive lite.
A second error is accepting a fire listing while overlooking impact safety. Traditional wired glass may be accepted for fire performance but rejected because it does not satisfy the applicable CPSC impact category [S3]. A third error is substituting a generic ceramic sheet for a tested laminated or filmed fire-protection product, because material identity alone does not establish a compliant door lite [S5].
Substitution and field modification are the principal failure points. The installer should verify the glazing label, door and frame labels, listed size, impact category, compatible lite kit, and any glazing bead or sealant requirements before installation. Replacement cost after fire damage can also affect lifecycle decisions, as discussed in Fire Door Replacement Cost After Fire Damage.
Before ordering, obtain the exact vision-panel listing from the door manufacturer or code official, document the selected glass type and dimensions, and confirm that the complete door assembly remains within its tested fire and impact-safety requirements.