New dump-truck listings generally ranged from about $58,000 to $311,000 in October 2026, but the provided sources do not establish pricing specific to 16-cubic-yard tandem-axle models [S2].
The quoted market covers several chassis, body, axle, mileage, and upfit configurations, so the body capacity alone does not determine the purchase price [S2][S4][S5].
16-Yard Truck Price Range and Market Position
New dump-truck listings ranged from approximately $58,000 to $311,000 in October 2026, while used listings commonly asked $38,000 to $245,000 [S2]. These figures describe the broad dump-truck market, not a single quoted price for every 16-yard tandem configuration.
Within the new heavy-truck segment, the reviewed listings included a 2026 Kenworth T480 tandem-axle dump truck with a Paccar 370 hp engine, a 6-speed Allison RDS automatic transmission, and a 16-foot dump body, listed at $169,995 [S7]. The rental-market tandem-axle dump truck has load capacities from 10 up to 16 cubic yards and includes a motorized mesh tarp [S5].
Pricing a new dump truck over 33,000 pounds may involve a 12% federal excise tax [S2]. This makes gross vehicle weight rating, tandem-axle ratings, chassis model, and body construction more useful procurement filters than the familiar 16-yard label. Under the federal bridge formula, 34,000 pounds is the maximum aggregate weight on a single tandem axle, while an individual axle on a standard axle is generally limited to 20,000 pounds and the general gross vehicle limit is 80,000 pounds. The broader equipment categories for a dump truck are covered separately from the narrower mining dump truck class.
New Versus Used Tandem-Axle Pricing
A used Class 8 dump truck typically sold for $40,000 to $150,000 in 2026 pricing guidance, while older single-axle and tandem-axle trucks with higher mileage occupied the lower-cost end of that market [S6]. The October 2026 listing review was broader, placing used dump trucks at $38,000 to $245,000 [S2].
Used heavy trucks under 100,000 miles had a median asking price of $209,995, compared with $99,900 for trucks past 400,000 miles [S2]. Those figures provide a stronger budget check than a generic used-truck range because they distinguish relatively low-hour assets from high-hour units.
For a 16-yard tandem truck, the economic case for buying used depends on the remaining life of the chassis, engine, transmission, axles, hoist, hydraulic system, and body. A lower purchase price can be offset by more downtime, shorter service intervals, and the cost of transferring a large-body configuration that does not match the intended route or material.
Chassis, Axles, Body, and Upfit Costs
A dump truck combines a manufacturer’s chassis with a hydraulic dump body installed by a separate body company, and the body and dealer upfit can move the final price substantially [S2].
The principal price drivers are therefore the chassis make and model, engine and transmission specification, GVWR, tandem-axle ratings, dump-body capacity and construction, hoist and hydraulic package, tarp arrangement, cab configuration, mileage, warranty, and dealer preparation. A 16-yard body with a motorized mesh tarp is specified for tandem-axle rear-dump vehicles intended to carry sand, aggregates, riprap, and asphalt [S5].
Two 2026 examples show how configuration controls the result. The Kenworth T480 example combines 370 hp, a 6-speed Allison RDS automatic transmission, a 16-foot body, and a $169,995 asking price [S7].
Payload and Capacity Must Be Checked Together
A 16-foot body length is also listed for the tandem 16-cubic-yard rear-dump configuration [S5]. These dimensional references should be treated as typical specifications, not as a substitute for the selected body’s certified data sheet.
Volume is calculated as interior length in feet multiplied by interior width in feet multiplied by side height in feet, divided by 27 [S4]. Material density then converts cubic yards into payload weight. Weight rather than volume is usually the binding constraint with dense materials such as gravel or wet sand, so load weight must be checked against the truck’s GVWR and axle limits [S4].
Any buyer must reconcile body volume, material density, GVWR, axle ratings, and local road restrictions before ordering. A mining dump truck may use a different sizing basis, so mine-duty requirements should not be inferred from a municipal 16-yard body.
Purchase Price Versus Total Operating Cost
Purchase price captures only one part of the decision. For a 16-yard tandem truck, operating cost also includes fuel, tires, inspections, preventive maintenance, hydraulic service, body and hoist wear, insurance, registration, and the cost of carrying material at less than full payload when density prevents the volume rating from being used [S2][S4].
Delivery, sales tax, titling, and registration can also change the delivered amount. The rental listing for the 16-cubic-yard tandem truck explicitly excludes freight, delivery, tax, titling, and registration from its rate, and requires written confirmation of price, specifications, and availability [S5]. A buyer comparing a dealer’s cash quote with a rental or contract alternative should normalize all five items before calculating cost per load.
Fuel consumption should be checked with the selected engine and expected operating cycle rather than assumed from the axle class. Payload utilization should be calculated from material density and legal weight limits. Maintenance exposure should include the hydraulic system and hoist because these are essential to every dump cycle, while tire cost rises with tandem configuration and site conditions. The ownership threshold is reached when annualized purchase, financing, maintenance, and utilization costs fall below the equivalent rental cost for the required hours and delivery schedule.
2026 Buying Criteria and Price-Check Method
A defensible 2026 budget for a new tandem-axle 16-cubic-yard dump truck should be built from the selected heavy chassis rather than from the $58,000–$311,000 market envelope alone [S2]. The documented $169,995 Kenworth T480 listing provides a concrete reference for a 370 hp, 16-foot-body configuration, but it does not establish a universal price [S7].
Buyers should request a build sheet showing the chassis model, GVWR, front and rear axle ratings, engine, transmission, 16-cubic-yard body dimensions, empty weight, hoist, hydraulics, tarp, tires, warranty, and delivered price. Tandem 16-cubic-yard trucks are offered across multiple chassis makes and models, and the stated capacity spans 10 to 16 cubic yards across the broader rental class [S5].
Public procurement also demonstrates live demand for the configuration. Louisiana solicitation 3000026753 sought 16-yard tandem-axle dump trucks with a bid opening scheduled for October 28, 2026 at 10:00 AM CST [S3]. For fleet or project buying, compare dealer asking prices, awarded public bids, and rental rates for equivalent payload and availability, then track delivered price and hours by body since the original listing date.
The next trackable procurement signal is the awarded price or contract rate for solicitation 3000026753, together with dealer quotes for equivalent 16-yard builds. Comparing those figures with the $169,995 Kenworth example and the October 2026 new-truck range will produce a defensible budget without treating unrelated Class 8 listings as direct price matches [S2][S3][S7].