A rotary index table drive should use a 4-groove, preloaded ball spline when the shaft must transmit torque while supporting an integrated radial bearing.
Final sizing must reconcile torque, overturning moment, radial load, speed, stroke, life, mounting space and accuracy across the fixed housing and rotating table.
Choose Rotary, Medium-Torque or High-Torque Architecture
A rotary ball spline combines a grooved shaft, spline nut and rolling elements in one package: the rotary nut includes a radial support bearing, avoiding a separate stacked bearing arrangement and reducing overall envelope [S3][S5][S6].
THK identifies Type SLS as a high-torque caged-ball ball spline and states that the SLS/SLF models use caged-ball technology to support high-speed response and improved torsion and flexural rigidity [S1]. A rotary-type unit is the direct choice for an index table whose load path requires a rotating nut with radial support. A medium- or high-torque spline with a separate radial bearing becomes relevant only when a fixed nut, unusual end support or custom shaft arrangement is unavoidable.
THK lists Type SLS-L high-torque caged-ball ball splines in nominal shaft diameters from 25 to 60 mm [S1]. The rotary-bearing arrangement is more compact than fixing a standard spline nut and adding radial bearings externally, but it still requires confirmation of radial load, moment load and allowable rotation speed [S3].
A plain ball spline is therefore not the same selection as a rotary index-table support. Confirm that the candidate catalog has a rotary nut with an integrated angular-contact or crossed-roller support, rather than assuming that a standard spline nut can carry overturning load.
Match Groove Architecture to Torque and Stiffness
A 4-groove shaft has a higher torque rating than a 3-groove shaft because additional grooves increase the available ball-contact geometry [S3][S5][S8]. Gothic-arch grooves with four-point ball contact also provide higher ratings than circular-arch grooves with fewer contact points [S5].
For an index table, 4 grooves and four-point contact are the stronger starting architecture when torque and angular rigidity are priorities. The torque rating is not a single catalog number; it is governed by groove count, points of ball contact, shaft section and applied loading [S8].
Those figures belong to Thomson designs, not every ball spline. Use them to compare architecture, then use the selected manufacturer’s load and life tables for the actual size.
Preload for Indexing Accuracy and Life

Preload removes clearance between shaft and spline nut, eliminating the angular backlash that otherwise appears as the shaft starts rotating and the nut moves slightly before following [S3][S5].
Higher preload increases initial rigidity, assembly accuracy and response to small indexing motions, but it also raises rolling friction and contact force [S3][S5]. The practical selection rule is not “maximum preload.” It is the lightest preload grade that satisfies the permitted angular error, repeatability and moment-deflection requirements without shortening calculated life.
For an index table, three acceptance checks should be tied to the drive specification: shaft rotation relative to the nut, angular displacement under table load, and starting torque. If the application indexes continuously, inspect how the selected preload affects drive torque and heat generation. If it dwells at one position, stiffness under a constant overturning moment may control the grade more than peak dynamic torque.
Do not use a torque rating alone to choose preload. A high-torque rating does not guarantee low backlash, while a low-backlash assembly can still be unsuitable if its preload creates excessive friction or heat. Document preload class, permitted operating temperature, lubrication method and service interval with the selected assembly [S1][S2].
Compare Rotary Support Bearing Options
Rotary ball spline nuts use either angular-contact ball bearings or crossed-roller bearings, and the two options must be judged against overturning load, stiffness, speed, envelope and installation requirements [S3][S5].
The comparison cannot be completed from architecture alone. Load magnitude, load direction, table diameter, mass, center-of-gravity offset and cycle profile determine which support can meet life and stiffness requirements [S3][S5]. Crossed-roller guidance is not interchangeable with angular-contact guidance in every orientation, and its permissible installation axes must be checked against the table’s overturning load.
For a table with reversing or multi-axis loading, document the moment vector and confirm the bearing orientation with the manufacturer. For a continuously rotating spindle, use the rotary nut’s rated rotational speed and check the attached seal or cable-management components as part of the high-speed envelope [S1][S2].
Size the Shaft from the Actual Table Load

Rotary ball-spline selection starts with 10 inputs: stroke length, velocity, applied load, mounting space, duty cycle, required life, dimensions, installation direction, environment and accuracy [S5].
Separate the loads into torque transmitted through the spline, radial force applied to the rotating support, overturning moment caused by the table mass and eccentricity, and axial force if the drive also translates [S2][S6]. Thomson’s selection method defines a minimum shaft section modulus from the calculated load case and then uses its size table to select the shaft [S2]. Apply the same logic to the rotary support bearing, with its own radial and moment ratings.
For a representative table calculation, use the required shaft torque T, transmitted power P, and speed n to establish the operating point, then compare that point with the candidate’s allowable torque and speed. During impact engagement, check peak torque separately from continuous torque. During indexing, compare radial load and overturning moment with the rotary nut’s rated capacity, and include any reducer, motor, table and fixture mass where they act on the supported shaft.
The catalog diameter is not the acceptance criterion. The selected assembly must satisfy torque, bending or moment load, speed, life and deflection simultaneously [S2]. Where torque and speed are both substantial, verify the manufacturer’s permissible operating envelope rather than extrapolating between published ratings.
Set Accuracy, Life and Environmental Limits
A rotary ball spline can support simultaneous linear and rotary motion with submillimeter accuracy, but submillimeter capability does not establish the repeatability required by a high-resolution index table [S3][S5].
Define repeatability, angular backlash, positioning error and allowable table deflection separately. Verify them against the selected preload and support-bearing configuration. Also specify required life by cycle count or service hours, because an index table may impose a high duty cycle even when average speed is modest.
THK states that SLS and SLF caged-ball models use evenly spaced circulating balls to reduce collision and mutual friction, limit particle generation, retain grease and support maintenance-free operation [S1]. That construction is advantageous for low-noise, high-speed motion, but the specific model’s speed, load, lubrication and environmental ratings still govern acceptance.
For contamination, seal, chip, temperature and chemical exposure, use the selected manufacturer’s limits and maintenance instructions. Do not infer suitability from a generic seal arrangement. The same applies to radial bearing support: its lubrication, service life and allowable speed must be included in the rotary spline selection.
Recommended Selection and Purchase Checklist

A 4-groove, preloaded rotary ball spline with an integrated angular-contact support is the default candidate for a compact, fast rotary index table with moderate-to-high torque and frequent indexing [S3][S5].
Use crossed-roller-supported rotary guidance when the table applies a heavy overturning moment and the manufacturer confirms the permitted orientation and operating speed. Do not select either type solely from the generic labels “high torque” or “precision”; require 10 numbers in the quotation: shaft diameter, spline and rotary-nut lengths, allowable torque, radial load, overturning moment, rotational speed, preload class, rated life, accuracy criterion and environmental limit.
Also request the shaft section calculation, bearing life calculation, mounting drawing, lubrication and maintenance plan, and a complete parts list for the shaft coupling interface. The assembly should also use an appropriate shaft collar or key arrangement only where the selected manufacturer permits it; torque transmission and axial location must not be assumed from the spline rating alone.
For an index table that combines torque, high rotational speed and repeated positioning, request samples and measure starting torque, angular backlash and positional repeatability under the intended preload. The final shortlist is the rotary spline whose published torque, speed, radial load, moment, life and accuracy limits all remain satisfied under one documented load case.