A rotating gripper axis should use a rotary ball spline when one shaft must support controlled angular positioning, axial motion, radial loads, and torsional reaction without a separate rotary bearing stack.
The selection must resolve shaft diameter, stroke length, applied torque, moment load, speed, duty cycle, preload, and mounting space before the nut and shaft family is chosen [S5][S6].
Define the gripper axis duty and motion architecture
A ball spline combines rotary and linear motion on one shaft: the nut can slide axially while transmitting torque through circulating balls, and the shaft can also translate through the nut [S1][S4]. This arrangement suits a gripper that must rotate around an object axis, retract or extend along that axis, or resist an off-center reaction force from the workpiece.
Three functional types are available: rotary type for angular positioning with limited linear movement, medium torque type for a balance of torque and straight-line motion, and high torque type for demanding rotational loads [S2]. For a gripper whose rotation is the primary function and whose axial travel is short or incidental, start with the rotary type. If the gripper must extend while rotating, compare medium- and high-torque families.
The architecture matters because rotating the nut drives axial rotation while allowing free axial motion, whereas moving the spline shaft with a linear actuator provides axial translation [S1]. A single-shaft architecture can also provide anti-rotation guidance and distribute load along more than one support point [S4].
Compare rotary, medium-torque, and high-torque ball splines
The decisive comparison is torque capacity against required axial load, while radial and moment loading, speed, installation size, and permitted axial travel determine which type remains viable. THK lists nominal shaft diameters of 25–60 mm for the high-torque SLS-L caged-ball type [S2].
The high-torque design is not automatically the better gripper choice. Its larger contact angle and angular rigidity favor high-load transmission, but the nut envelope, preload, heat generation, and cost must still fit the gripper. Conversely, a rotary type should not be selected for a gripper that must combine continuous rotation with substantial axial force or a long translating stroke.
Calculate shaft size from torque, moment, and support spacing

Shaft diameter is not a free mechanical choice: it sets the available torque and moment capacity for the selected family. THK lists nominal shaft diameters of 25–60 mm for the high-torque SLS-L caged-ball type [S2].
Record the maximum commanded torque, external reaction torque, axial force, radial force, overhung gripper mass, center-of-gravity offset, and distance between the spline support and gripper tip. Ball splines are effective at resisting radial displacement caused by torque loads, while anchored nuts resist external torsional loading even when the shaft is stationary or extending [S1][S4].
Do not size from gripper mass alone. A compact tool held far from the spline creates a larger moment at the support than a heavier tool mounted close to it. The manufacturer calculation should use the actual load vector, support arrangement, and required service margin; published catalog capacities cannot substitute for those inputs [S5][S6].
Set preload, rigidity, and positioning accuracy
Preload is the principal selection choice when torsional stiffness and angular repeatability matter more than initial friction.
For a gripper that must hold its orientation while the workpiece imposes reaction torque, specify preload and angular backlash as separate acceptance criteria. Do not infer angular repeatability from axial repeatability, and do not use motor step resolution as a substitute for measured gripper positioning error. If the gripper also performs a controlled axial stroke, check whether preloading increases friction, heat, and required drive torque.
Ball guidance can reduce friction, wear, stick-slip, and seizure compared with sliding contact, but preload remains a design trade-off rather than a free accuracy setting [S4]. Models SLS and SLF adopt caged-ball technology to maintain the circulating motion of evenly spaced balls, eliminate collision and mutual friction between balls, reduce particle generation, achieve high-speed response, and realize stable and smooth motion with small rolling fluctuation; the SLS-L type has a nominal shaft diameter of 25–60 mm [S2].
Check speed, stroke, duty cycle, and thermal limits

Specify maximum angular speed, acceleration, axial speed, stroke, cycle count, and dwell time rather than relying on catalog peak speed alone. The starting selection inputs are stroke length, velocity, applied load, mounting space, and duty cycle [S5]. Ball splines can operate at high speed under torsional load, and the rolling-ball architecture supports high-speed motion with reduced friction and wear [S4].
For a gripper that indexes repeatedly, include the gripper inertia seen by the spline nut. Accelerating and decelerating the moving assembly can create torque peaks substantially above the static object weight. The drive, coupling, brake, and spline must all be checked for those peaks, including emergency-stop and jam conditions.
Do not assign a universal speed or temperature rating without the selected manufacturer’s model data. Seal material, lubricant, preload, shaft diameter, and duty cycle affect allowable conditions. The ball spline temperature limits with resin end seals reference provides a focused comparison for seal-dependent thermal limits.
Fit the nut, shaft, bearings, and mounting structure
A functioning gripper axis requires more than shaft and nut diameters: it also requires a supported nut arrangement, bearing support for the rotating element, an anchored housing, a drive connection, and clearance for the complete stroke [S1][S5].
Typical rotary ball-spline architectures use a common anchoring point such as a round tube fixed to a bracket, with the nut supported by a bearing [S1]. For a gripper, verify radial shaft clearance, axial nut travel, runout, coupling alignment, and whether the gripper structure can react torque without distorting the spline. The high-torque SLS/SLF shaft design uses a more circular geometry to improve torsional and flexural rigidity [S2].
Check whether the nut can be serviced or replaced without removing the entire gripper. THK offers LT-X and LF-X nuts whose external dimensions match corresponding LM-series or LMF linear-bushing dimensions, allowing substitution between those nut formats within the stated dimensional families [S2]. This interchangeability can reduce assembly effort only when shaft, preload, load rating, and sealing requirements remain acceptable.
Identify unsuitable applications and failure modes

A ball spline is a poor choice when the axis requires only rotation, no axial guidance, and no meaningful torsional or moment load. In that case, a dedicated rotary bearing or crossed-roller guide may provide a simpler load path with fewer rolling-contact elements. A ball spline becomes stronger as a selection when compact packaging, combined linear-rotary motion, and resistance to torsional loading justify the added nut and shaft interface. [S4]
Do not use a ball spline to compensate for structural deflection or an improperly aligned actuator. Misalignment can concentrate contact forces, increase friction and wear, and shorten service life. Likewise, a screw-driven arrangement such as a ball screw provides rotary-to-linear conversion but does not provide the same direct rotary gripper-axis architecture; compare that arrangement separately when the gripper requires a powered axial extension rather than a rotating tool axis.
The principal failure modes are overload from shock or jam conditions, excessive preload, contamination of the circulating-ball path, lubrication loss, and shaft deflection that distorts the rolling contact. A design review should identify each load direction, distinguish static from dynamic capacity, and document the inspection interval for lubrication, seals, mounting fasteners, and rotational backlash.
Convert catalog dimensions into a purchase specification
The purchase specification should identify the ball-spline family, nominal shaft diameter, nut type, shaft length, number of crests, ball-row arrangement, contact angle, preload arrangement, allowable torque, moment load, axial load, speed, duty cycle, seals, lubrication, and mounting interfaces. Model families are more useful than generic product labels: SLS/SLF caged-ball high-torque shafts cover 25–60 mm, LBS high-torque shafts cover 15–150 mm, LT medium-torque shafts cover 4–100 mm, and LBR/LBH rotary shafts cover 15–50 mm [S2].
Separate catalog facts from design outputs. The family diameter ranges, contact angles, crest counts, and row counts are catalog data [S2]. Required torque, moment, life, and allowable speed are engineering outputs derived from the gripper load case and must be checked against the selected manufacturer’s load table [S5][S6].
For a practical shortlist, compare at least the rotary, medium-torque, and high-torque options at the same required stroke and mounting envelope. Reject any candidate that lacks sufficient torque or moment margin, cannot carry the axial load at the selected preload, or requires a nut envelope incompatible with the gripper structure. The final choice is the smallest family that satisfies all calculated loads and duty requirements with the specified preload and mounting arrangement.