Full ceramic bearings can run completely dry and do not need lubrication to run [S4].
The practical scope is narrower than “any ceramic bearing in any sea”: continuous immersion suits corrosion-resistant ceramic rolling elements, while cage material, fits, speed, load, and contaminant exclusion still govern reliability [S2][S3].
Full ceramic bearings can be used in seawater environments and offer high chemical resistance [S8]. Ceramic is non-porous, which removes the moisture-retention and rusting mechanism associated with steel-bearing races [S4].
Both silicon nitride, Si3N4, and zirconia, ZrO2, have excellent corrosion resistance and low friction characteristics. Their hardness also supports low wear rates, while the non-metallic rolling elements provide electrical insulation between the shaft and housing [S2].
That corrosion resistance does not make a bearing immune to mechanical damage. Saltwater can carry sand, shell fragments, and other abrasives; bearing life still depends on preventing those contaminants from reaching the raceway-contact interface.
Material Comparison for Seawater Exposure
Ceramic bearings are suitable for marine environments, while the appropriate bearing material, coating, seal, and lubrication must be matched to the specific exposure level [S2][S3].
This comparison separates corrosion resistance from service suitability. Full ceramic wins the continuous-submersion criterion, while a metal bearing can remain economical when exposure is limited to salt spray, humidity, or intermittent splash.
Load, Speed, and Lubrication Limits

Ceramic bearings do not require lubrication simply because they are ceramic. Full ceramic bearings can run completely dry, and regular tap water is among the cleaning agents identified for removing contaminants from them [S4][S5].
Dry running is not a blanket permission for every load and speed. Silicon nitride and zirconia bearings have low friction and can operate without lubrication in lower-speed applications, but the permissible load and speed still depend on the specific bearing, its internal geometry, and the cage [S2].
Full ceramic removes the seawater-rust problem, but it does not remove the need to respect the manufacturer’s dynamic load rating, speed limit, and mounting instructions.
Full ceramic bearings fit applications where continuous seawater contact is unavoidable and elastomer seals would create an avoidable corrosion or wear problem. Documented uses include underwater drones, subsea equipment, propeller shafts, and underwater instrumentation [S2][S7].
Full ceramic bearings can run without lubrication, making them a credible option for applications where dry operation is required [S4].
They are not the automatic choice for every marine bearing.
Weaknesses Around Seals, Cages, and Contamination

The absence of a seal does not guarantee clean operation. Open bearings generally have no sealing lip, making it easier for water to enter [S6].
The cage deserves a separate specification review because a full ceramic bearing may combine ceramic balls with a non-ceramic cage. Seawater compatibility must be established for the complete assembly, not inferred from the Si3N4 or ZrO2 rolling elements alone.
Seal-free construction also exposes the bearing to wet-dry cycling, salt concentration, abrasive particles, and impact loading. A robust design uses an appropriate shaft and housing fit, limits edge loading, protects the housing from sand and shell fragments, and verifies the cage material against continuous immersion [S2][S3].
Specification Checks Before Ordering
A seal-free full ceramic bearing should be ordered against five verifiable items: ceramic grade, complete material list, dynamic load rating, speed limit, and manufacturer confirmation of seawater exposure [S1][S2][S3].
The ceramic bearing designation alone does not confirm suitability. Review whether the cage is polymer or metal, whether the bearing is open or shielded, and whether any shield coating or adhesive remains compatible with continuous saltwater exposure [S4][S6].
For comparison, a hybrid ball bearing with steel races retains steel components that require corrosion protection, while a fully ceramic design removes those metallic raceway surfaces [S2]. The procurement specification should therefore distinguish full ceramic from ceramic hybrid by materials and performance data, not by the generic word “ceramic.”
For an underwater application, request a manufacturer statement covering continuous immersion, the specified seawater exposure level, dry or lubricated operation, allowable speed, and contamination limitations. Record the exact bearing designation, material pairings, and test conditions in the maintenance file.