Porous materials can absorb and spread a mark, while non-porous or coated materials can change wetting, drying and adhesion; inspect bleeding, edge definition and contrast after the agreed waiting time, and record the dry-time window [S1].
The decisive variables are substrate porosity, coating, surface energy, cleanliness, drying time and printer fluid-path compatibility, not the broad labels “paper” or “plastic” [S1][S4].
Substrate behavior determines the ink decision
A porous surface absorbs part of a liquid ink, while a non-porous surface keeps most of the ink on the surface, shifting the performance burden toward wetting, adhesion and drying [S4]. Porous examples include uncoated corrugated board and paper sacks, where fiber content, recycled content, dust, color and batch variation can alter bleeding and edge definition [S1].
Coated cartons, films, smooth plastics, glass and metal are commonly non-porous or only partly absorbent, but each production grade can behave differently [S4]. A visual inspection does not establish compatibility. Record the exact material, coating, surface color and texture, printed side, contamination condition, line speed, stand-off distance, dry-time window and required pass/fail method before selecting an ink [S1][S4].
Porous materials can absorb and spread a mark, while non-porous or coated materials can change wetting, drying and adhesion, so neither category proves that a particular ink will work without a line test [S1]. This rule also explains why substrate category alone does not approve an ink. A representative production sample and a line-speed trial remain necessary [S1][S3].
Comparison of porous and non-porous ink choices
On uncoated paper and board, an ink designed for rapid surface filming can spread as the liquid penetrates, reducing fine-edge definition; inspect bleeding, show-through and barcode quality after the agreed waiting time [S1][S4]. On coated carton, a reduced-absorbency surface behaves more like a non-porous substrate, making adhesion, drying and rub resistance more dependent on ink chemistry and surface condition [S4].
Against four decision criteria, porous-compatible coding favors absorption into uncoated paper and board, with less concern about rapid surface filming but greater sensitivity to bleeding and edge spread. Non-porous coding favors plastic, glass, metal and rubber, with rapid drying and defined surface transfer but greater sensitivity to wetting and contamination. Universal ink can mark porous surfaces when faster drying or weather resistance is required, although this route increases ink cost [S6]. Cost, durability and application effort therefore vary by formulation rather than by substrate name alone.
Match ink chemistry to plastic and coated surfaces

Polypropylene and polyethylene, including HDPE, have low surface energy, so liquids tend to bead, character edges can break up and adhesion may weaken [S3]. PET occupies an intermediate position and can accept a suitable solvent balance after oils and mold-release residues are removed. PVC performance varies with plasticizer content and coating, so one grade should not be assumed to cover all PVC [S3].
A spreading test with isopropyl alcohol provides a practical surface check: even spreading suggests sufficient surface energy for many quick-dry inks, while beading points toward a low-surface-energy formulation, light pretreatment or both [S3]. Clean the test area with a lint-free cloth and isopropyl alcohol, then do not touch the print zone. Finger oils, slip agents and dust create local adhesion failures, including parts that print inconsistently within the same batch [S3].
For clear PET bottles, the recommended starting trial is a quick-drying dye-based ink balanced for PET, with thin characters at 1.6–2.5 mm height; typical set times are 2–5 seconds depending on airflow and part temperature [S3]. For black HDPE caps, use a white pigmented ink formulated for low-surface-energy plastics and support the cap with a pocket or guide to prevent movement [S3]. These values are trial starting points, not universal production settings.
Printer setup can reverse an apparent ink failure
Mechanical reciprocating coders transfer a thin, even film when pressure, dwell and head rotation are controlled. Overpressure floods or smears the stroke, while insufficient pressure produces light, discontinuous marks [S3]. On caps and other small-diameter parts, guides, pockets or starwheels stabilize the strike point; bounce and roll increase apparent dot gain and blur character edges [S3].
Character height is a process variable, not only a typographic choice. Smaller characters transfer less ink, set faster and retain sharper edges on non-porous surfaces, while oversized characters on small curved areas deposit excessive ink and extend set time [S3]. For a coding machine, approve the complete combination of ink, substrate, print geometry, speed and support arrangement rather than treating ink approval as independent of machine setup.
Fluid-path compatibility must also be explicit. The #100 alcohol-based coder ink is restricted to specified non-porous hand printers, fixed-mount coders and USMR-20 micro-spray markers, and must not be used on Micro Cell ink rolls [S2]. For continuous inkjet or thermal inkjet systems, cartridge and fluid-path restrictions remain system-specific; the general substrate trial cannot authorize a cross-platform ink swap.
Porous and non-porous failure modes

Porous failures typically appear as edge spread, bleeding, reduced fine-character definition, show-through or inconsistent absorption across paper and board batches [S1][S4]. The evaluation must wait for the agreed set time, because judging a porous mark too early can confuse delayed absorption with poor transfer [S1].
Non-porous failures appear as beading, poor wetting, wipe-off, broken character edges, flooding, smearing or delayed setting. Curvature, condensation, oil, mold-release residue, reflective surfaces, web movement and downstream contact can all affect the result [S4]. Film flexing, seal heat, abrasion and contact with forming or conveying equipment must therefore be included in a packaging validation [S4].
Print the complete job during validation: the largest message, smallest character and every machine-readable symbol used in production. Test normal and maximum speed, pitch, starts, stops and actual print distance, then allow the real set time before checking adhesion and appearance [S4]. Condition samples under the normal temperature, humidity, condensation, dust, oil, splash and cleaning conditions relevant to the package [S4].
Build a repeatable line trial
Approve the substrate, ink and printer settings as one combination. Start with production-equivalent samples, record the supplier reference, coating, color, treatment and printed side, and condition the samples under the intended handling environment [S4]. For DOD selection, document material and coating, surface color and texture, ink system, fluid-path compatibility, line speed, stand-off distance, dry-time window, required resistance and pass/fail method [S1].
Run the test at production speed with the largest and smallest messages, test curved parts at the expected orientation, and evaluate the mark after the full downstream handling cycle. Inspect adhesion, edge definition, barcode or code readability, contrast, rub resistance and scanner performance. Keep the accepted ink cartridge or container tied to the approved substrate and application [S4].
For universal-ink substitution, compare the full job rather than a coupon. Universal inks can be used on porous material when fast drying or weather resistance is needed, but their use on non-porous surfaces can increase ink cost [S6]. That trade-off is defensible only when the added drying performance, exposure resistance or changeover reduction has a measurable operational value.
The next engineering record should contain three traceable items: the exact substrate and coating description, the approved ink grade with printer fluid-path restriction, and the signed trial result stating speed, set time, environmental condition and pass/fail method. Any change to material supplier, coating, cleaning chemistry, character size or line speed requires a new compatibility check.