An engineering-plastic sliding bearing should be selected by comparing its calculated operating PV with a grade-specific limiting PV under comparable test conditions, then checking pressure, speed, temperature, clearance, lubrication and shaft material separately [S1][S2].
The calculation is simple: projected pressure in MPa multiplied by relative sliding speed in m/s gives operating PV in MPa·m/s, while the allowable PV limit depends on the exact polymer grade, bearing geometry, temperature, mating surface and failure criterion [S2][S3].
PV Limit Definition and the Wear-Factor Distinction
Operating PV is the product of average contact pressure and relative surface velocity, with the standard screening equation written as PV = P × V [S3]. Pressure is expressed in N/mm², equivalent to MPa, and velocity in m/s; their product therefore has units of MPa·m/s [S2][S3].
Limiting PV is the maximum allowable PV associated with a particular material and test arrangement without early failure or substantial loss of performance [S3]. It is not a universal wear factor and cannot be transferred directly between manufacturers or grades without the supporting conditions [S1][S2].
A PV limit describes a pressure-velocity boundary, not a bearing-life rating [S1][S2]. The historical evaluation of plastic bearing materials treats sliding severity as a combined pressure and velocity duty, while later analysis extends limiting-PV relationships by incorporating an estimate of mean surface-temperature rise [S1][S9].
Calculate Operating PV for a Sleeve Bearing
For a cylindrical shaft rotating inside a stationary sleeve, projected area is A = d × L, average projected pressure is p = F/A, and relative surface speed is v = πdn/60000, producing application PV = pv [S2]. Shaft diameter d and bearing length L are in millimetres, radial load F is in newtons, and rotational speed n is in rpm.
A 20 mm shaft with 25 mm bearing length under a 500 N radial load at 120 rpm has a projected area of 500 mm², an average pressure of 1 MPa, a surface speed of approximately 0.126 m/s and an operating PV of approximately 0.126 MPa·m/s [S2]. This is an arithmetic screening example, not a material rating or approved duty.
Projected pressure must be distinguished from pressure over the entire cylindrical bore surface [S2]. A thrust washer also requires a different contact-area and velocity calculation. Local edge loading from misalignment is not resolved by the simple projected-area method, so alignment remains a separate design check [S2].
Unit discipline is mandatory because metres per minute and metres per second differ by a factor of 60 [S2]. PV also scales directly with changes in either pressure or speed: doubling load at unchanged speed doubles pressure and PV, while doubling rpm at unchanged load doubles velocity and PV [S2].
Compare Polymer Options by Decision Criteria

No single limiting-PV number supports a fair comparison across polymer families because the reported value is tied to material, test geometry, operating temperature, lubrication and the defined failure point [S1][S2]. The useful comparison is therefore between complete material packages rather than isolated figures.
Material selection should start from the engineering plastic family, then move to the exact grade and manufacturer data. Nylon, acetal, PEEK, PTFE and other engineering thermoplastics have different stiffness, thermal behavior, wear behavior and permissible sliding duty, so a generic family label is not a procurement specification.
For heavily loaded or temperature-sensitive mechanisms, nitrile rubber and EPDM rubber may be considered as elastomeric alternatives, but their allowable loading must be evaluated on the same application basis. Elastomer selection remains outside a rigid PV screening rule because deformation, friction and thermal behavior differ from rigid engineering-plastic bearings.
Apply Limiting PV as a Screening Filter
Application PV should first be compared with the limiting PV for the exact grade and closest available operating conditions [S2][S3]. Passing this comparison means further design review is justified, not that the drawing is approved, wear rate is known or a replacement interval has been established [S2].
The limiting-PV record should identify the geometry, temperature, shaft material, lubrication condition and failure criterion used to establish it [S2]. For plastic sliding bearings, the bearing-to-shaft running clearance is identified as a governing factor in PV performance, making dimensional verification mandatory rather than optional [S6].
Pressure, speed and thermal capability must remain separate checks even when calculated PV is below the quoted boundary [S2]. Increasing sleeve length can reduce nominal projected pressure if load distribution remains valid, but the arithmetic does not establish uniform contact or resolve alignment [S2].
Nylon design guidance distinguishes the application’s actual limiting PV from the material value because environmental temperature changes the allowable duty [S5]. A supplier limit stated for 66°C, for example, cannot be treated as an unrestricted value at another service temperature; the exact test and operating assumptions must remain attached to the calculation [S5].
Thermal Limits Can Override a Nominal PV Screen

Thermoplastic sliding bearings have limiting PV values that depend on operating conditions, including temperature [S1][S2]. The limiting relationship should be checked under the closest available operating conditions, including the application temperature [S2][S5].
Limiting-PV analysis for thermoplastics includes estimated mean temperature rise because the same pressure-velocity combination produces different results as the material temperature changes [S9]. A design that passes a room-temperature limit can still be unsuitable if frictional heating, poor heat rejection or high ambient temperature pushes the polymer beyond its permitted service condition [S1][S9].
The Vesconite metric guidance provides one concrete reference point: 30 MPa, equivalent to 300 kg/cm², is recommended for general applications at negligible sliding speed [S8]. Surface speed is calculated from rpm, a factor of 3.14 and shaft diameter [S8]. The negligible-speed qualification matters because the 30 MPa figure is not a general high-speed sliding limit.
For a rotating shaft, surface speed can also be derived from circumference multiplied by rotational frequency. The working speed, shaft diameter and selected grade must remain visible beside the PV calculation so the result can be reproduced without an implicit unit conversion [S2][S8].
Limits, Failure Modes and Misuse of Wear Factors
Exceeding the limiting PV can lead to excessive wear, overheating and related loss of bearing performance [S3]. These failure modes are related but should not be collapsed into one another: a bearing may remain below its thermal limit while showing unacceptable wear, or operate within a quoted PV boundary yet suffer edge loading caused by shaft misalignment [S2][S3].
PV does not directly specify life in operating hours [S2]. A lower PV generally indicates a less severe sliding duty, but actual wear still depends on the material grade, mating shaft, lubrication, clearance, temperature, duty cycle and contamination [S2][S6]. Treating PV as an inverse life curve without supporting test data would overstate what the screening calculation can establish.
Common calculation errors include using bore surface area instead of projected area, mixing velocity units, overlooking intermittent peak loads, and applying a supplier limit from a different lubrication or temperature condition [S2]. Record constant load, variable load and short-duration peak duty separately because the nominal average can conceal the condition that drives wear [S2].
For nylon applications, the supplier’s environmental-temperature example is especially important: the stated operating condition includes 66°C, and the resulting limit belongs to that application rather than to nylon as an unrestricted material [S5]. Recalculate the duty when ambient temperature, shaft diameter, speed, load or bearing length changes.
Build a Traceable Bearing Qualification Record

A defensible bearing record contains at least 9 controlled items: shaft diameter, bearing length, radial load, rotational speed, projected pressure, sliding speed, calculated PV, quoted limiting PV and the test conditions attached to that limit. These fields make the screening calculation reproducible and expose missing assumptions [S2][S3].
The record should also identify the polymer grade, shaft material, surface finish, running clearance, lubrication method, ambient temperature, estimated frictional temperature rise, load direction, duty cycle and misalignment allowance [S2][S6]. For temperature-sensitive selection, the resin-specific service-temperature data should be cross-checked against the engineering plastic RTI selection guide rather than inferred from PV alone.
The next actionable step is to compare the installed operating point with the supplier’s exact limiting-PV conditions. If the calculated PV is near the limit, or if clearance, temperature, lubrication or shaft data differs from the test, request application-specific qualification data before releasing the bearing drawing.