In Class I, Division 1 and 2 locations, conduit seals are required within 450 mm (18 in.) of the point of entry to any explosion-proof enclosure, with the sealing compound poured to a minimum thickness of 5/8 in. and a minimum 93°C melting point, consistent with NEC 501.15(C) practice [S2][S4].
Two distinct engineering goals drive that placement rule: the seal must contain an internal explosion inside the explosion-proof enclosure and stop flame propagation through the conduit raceway, and it must also minimise the migration of gases or vapors from a hazardous zone into a non-hazardous one [S2]. The "18-inch" distance is not a guideline; it is the maximum allowed separation between the seal and the enclosure wall.
Where the 18-Inch Seal Must Be Installed
The 450 mm (18 in.) rule applies at every transition between a Class I hazardous area and an explosion-proof enclosure, and a second seal is required where the conduit crosses from the hazardous boundary into a non-hazardous space [S4][S6]. NEC 501.15(C) also requires that the seal sit on the proper side of the boundary; seal-off fittings for boundary separation must be located where the conduit leaves the classified location, not inside the safe area [S2].
Sealing fittings cannot contain splices, must be listed for the duty, and must remain accessible for inspection and re-pouring; an inaccessible seal is a code violation, not a maintenance issue [S2]. Horizontal runs need fittings with a cover opening that can be rotated to accept the sealing compound; vertical-only fittings (such as the Eaton Crouse-Hinds EYS series in 1/2" through 1" trade sizes) cannot be installed in a horizontal run without voiding the listing [S1].
Compound Thickness, Melting Point, and Conductor Fill
The poured compound must be at least 5/8 in. thick and never less than the trade size of the conduit itself; a 2 in. conduit therefore needs a compound plug at least 2 in. deep [S2]. The compound must keep a melting point no lower than 93°C (200°F) so it survives the thermal pulse of an internal ignition event inside the explosion-proof junction box it protects [S2].
Conductor fill is restricted in any raceway that terminates in a seal: NEC Chapter 9, Table 1 normally permits up to 40% fill, but the effective limit drops to 25% of the raceway cross-section once a sealing fitting is in line, so conductors have room to spread and the compound can encapsulate each one individually [S2]. Going over 25% bunches conductors in the centre of the plug and leaves gas paths around them, defeating the seal; some manufacturers offer oversised listed fittings that legitimately retain 40% fill, but only when the listing explicitly allows it [S2].
EYS vs EZS: Vertical-Only vs Any-Angle Fittings

Two fitting geometries dominate the market, and the choice is dictated by the conduit run, not by preference. Eaton Crouse-Hinds series EYS fittings are listed for vertical-only or vertical-and-horizontal installation depending on the catalog number, and many of the smaller trade sizes (1/2", 3/4", 1") are restricted to vertical-only; these are the workhorse seals for Group B (hydrogen) atmospheres when specified in Feraloy iron alloy or copper-free aluminium [S1].
Series EZS fittings, by contrast, are designed for installation at any angle, with a cover that can be rotated so the sealing-compound opening always faces upward regardless of pipe orientation; trade sizes 1-1/2" through 3" are typically Feraloy iron alloy or ductile iron and are not Group B rated [S1]. For a process skid with mixed-orientation conduit, the practical decision matrix is: EYS vertical-only for the smallest trade sizes and any Group B run; EZS any-angle for 1-1/2" and larger where the routing is non-vertical.
What a Conduit Seal Does, and What It Does Not Do
A conduit seal is a flame-arrestment plug, not a pressure vessel; it is built to let the pressure of an internal explosion cool below the ignition temperature of the surrounding atmosphere as the gas passes through the small gaps around conductors and the compound, but it is not designed to hold positive pressure indefinitely [S9]. In an Ex d (flameproof) system, the enclosure itself is engineered to withstand the peak explosion pressure; the seal's job is to stop the flame front from travelling down the pipe to the next enclosure [S9].
Three failure modes recur in field audits. First, the fitting is never poured, on the assumption that the wires may need to be pulled later, which is a code violation; pulling is done through the conduit body, not the seal [S2]. Second, silicone or electrical sealing putty is used in place of a listed compound, which melts below 93°C and loses integrity during an internal event [S2]. Third, conductors are bundled at more than 25% fill, leaving channels around the bundle through which gas can migrate even when the compound is correctly poured [S2].
Standards Governing the 18-Inch Rule

For US projects, the rule traces to NEC Section 501.15(C) for Class I, Division 1 and 2 wiring, with the boundary-seal language in 501.15(A) and cable-seal language in 501.15(D) [S2]. The companion IEC framework, IEC 60079-1 for Ex d (flameproof) enclosures, calls for a certified flameproof "d", "tb", and IP66 sealing device such as a stopping box with setting compound either inside the flameproof enclosure or immediately at its entrance [S4].
For European ATEX 2014/34/EU equipment, the equivalent requirement is that the stopping box be located at the enclosure entry or inside it, and the compound must be listed for the specific fitting model; mismatched compound and fitting, even when both are individually certified, is not a compliant assembly. Field installers should treat the NEC 501.15(C) language, the IEC 60079-1 stopping-box language, and ATEX 2014/34/EU as three different phrasings of the same physical rule, and verify the fitting's group rating (B, C, D) against the gas group present in the room [S7][S8].
Selection Criteria and Common Configurations
Specifying a seal fitting reduces to four checks: trade size (must match the conduit), material (Feraloy iron alloy / ductile iron for impact-prone areas, copper-free aluminium for weight- or corrosion-sensitive skids), orientation (vertical-only EYS vs any-angle EZS), and gas group (Group B rated for hydrogen, otherwise standard C/D) [S1]. For a typical 1" trade-size vertical conduit in a hydrogen service, the EYS16 or EYS316 (Feraloy, Group B) is the conservative pick; for a 2-1/2" non-vertical run in a hydrocarbon-only area, the EZS76 (any-angle, 2-1/2") is the direct match [S1].
Cable seals in 501.15(D) are a separate family: when a multiconductor cable passes through a seal, either the cable jacket is sealed inside the fitting with the compound, or the cable is terminated in an approved cable sealing device, and the same 18-in. placement rule applies [S2]. For Ex d cable entries on field equipment, the stopping box and setting compound are typically vendor-supplied with the explosion-proof light or explosion-proof button station; verifying the supplied seal matches the listed fitting is a routine pre-energisation check.
The most concrete field signal to track over the next quarter is whether project specifications continue to default to Group B rated EYS fittings for hydrogen service, or shift to EZS any-angle fittings for skid modularisation where conduit cannot be re-routed to stay vertical; the trend toward prefabricated skids with multi-plane conduit runs is the main technical driver pushing EZS adoption in 2026 builds [S1]. A second, smaller signal is enforcement of 501.15(D) cable-seal language on CCTV and pan/tilt installations in Class I areas, where the boundary seal is frequently omitted on the non-hazardous side of the conduit run [S4]. For related component decisions, see the spec comparison of Ex d cable gland sealing for cable entries where conduit is not used.