Integral and separated fixed gas detector architectures perform the same measurement function, but they divide sensor placement, transmitter access, and installation risk differently [S1][S3][S8].
Both provide continuous area monitoring rather than personal protection during short entries; fixed systems detect explosive, toxic, or oxygen hazards and can provide numerical readings and control outputs [S2][S5].
Architecture Definition and Functional Boundary
A fixed gas detection system uses a sensor near the potential hazard and a transmitter to convert gas concentration into an electrical signal for the detection panel [S3][S8]. The transmitter can be an integral part of the field instrument or a separate component connected to a remotely positioned sensor.
The Rosemount 925FGD features a Smart Sensor Module that connects to the transmitter and can be factory calibrated to butane, propane, methane, ethylene, or ethane.
This boundary matters when selecting a fixed gas detector for a hazardous area. The architecture does not change the measurement duty: an integral unit still requires the complete sensor, transmitter, enclosure, and connection to be compatible with the gas, temperature, humidity, and hazard location.
Selection Criteria: Access, Placement, and Environmental Separation
Separated architecture wins when the most representative sampling point differs from the best location for reading, calibrating, or servicing the transmitter [S1]. This is a direct engineering answer to a constrained access problem, not a generic preference for more components.
The Rosemount 925FGD is designed to operate in ambient temperatures ranging from -40 to 70 °C. The Rosemount 925FGD achieves an ingress protection level of IP66.
Integral architecture is preferable when one compact assembly can be placed at the sampling point, the instrument remains accessible, and a split sensor-to-transmitter installation adds no justified protection or service benefit [S4][S7]. The integral sensor-holder arrangement is intended to reduce module count and installation effort [S7].
Relative cost and maintenance frequency cannot be assigned numerically without a project-specific quotation and access study.
Integral Sensor and Transmitter: Compactness Versus Access

An integral sensor and transmitter combine the sensing element, signal processing, local display, and electrical interface in one enclosure, reducing physical separation and the associated field wiring [S7]. That arrangement suits a single known hazard where the sampling location is also serviceable and the detector can be mounted without a remote junction box [S4][S7].
The integral option is not suitable for every location. If the gas release point is near a ceiling, process vessel, ventilation duct, or another obstructed zone, remote sensor placement can improve exposure to the gas while keeping the transmitter accessible [S1]. The transmitter can then be maintained without moving the sensor into a hazardous atmosphere.
These values illustrate that a remote architecture does not necessarily place the larger, heavier transmitter at the gas sampling point.
Separated Sensor and Transmitter: Placement and Service Separation
A separated architecture is the stronger choice where continuous detection must remain in an awkward or hazardous service location while the transmitter is installed for easy access [S1]. The sensor and transmitter remain functionally linked, but physical access to each component can be optimized independently [S1][S3].
Added hardware, cable length, installation labor, and field-connection verification must be compared against the access and risk reduction obtained.
Separation does not eliminate sensor maintenance. The Rosemount 625 smart sensor retains its own configuration and calibration information, can be factory-calibrated for butane, propane, methane, ethylene, or ethane, and may be calibrated off-site before installation [S1]. Remote mounting therefore improves transmitter access, not sensor-service independence.
Use Cases and Explicit Architecture Comparison

Use an integral detector for one chemical storage room, one process point, or another application with a known hazard, one sampling position, and local continuous response [S4]. Use a separated detector when sensor placement must remain near the release point while the transmitter, local display, or controls need safer or easier access [S1].
Multi-point plants need a broader architecture decision because a standalone point can be appropriate for one local hazard, while several rooms, process areas, or gases make independent monitoring harder to coordinate [S4]. One AccuSafe controller can support up to ten sensor modules and monitor up to ten unique gases simultaneously, illustrating the different scale served by centralized multi-point architecture [S4].
Failure Modes, Limitations, and Sourcing Requirements
The principal failure mode of either architecture is a loss of measurement or communication at a point where continuous coverage is expected, and separated systems add junction-box, wiring, and termination points that must be included in inspection and commissioning [S1][S3]. A local display does not remove the need to verify the panel signal and alarm path [S2][S5].
Fixed systems have different performance envelopes. The Rosemount 925FGD measures hydrocarbon gases over 0–100% LEL, achieves ±3% LEL below 50% LEL and ±5% LEL above 50% LEL, and specifies humidity limits of 0–95% relative humidity at 52 °C [S1]. These figures are model-specific and should not be generalized to every sensor technology.
Specify certification from the exact detector model and gas configuration. The Rosemount 925FGD is certified to SIL 2 under IEC 61508 and carries ATEX, IECEx, and North American hazardous-area approvals, including AEx/Ex db IIC T5 Gb and NEMA 4X/IP66 [S1]. Marine fixed systems may also fall under IGC or GC regulation 13.6, with the US Coast Guard study guide requiring sequential sampling intervals not exceeding 30 minutes, an alarm at 30% LEL, and LNG continuous detection with fuel shutdown at 60% LEL [S3].
Document the gas, measurement range, output protocol, power supply, enclosure rating, temperature range, hazardous-area approval, calibration method, and inspection interval before ordering. Do not substitute a generic gas transmitter for a certified fixed detector, and do not infer detector performance from the output signal alone.
The next engineering decision is to mark the representative gas-release point, verify service access there, and then compare the combined mount with the remote sensor and junction-box layout. If the transmitter cannot be reached safely, use the separated arrangement; if both components can be serviced together without compromising coverage, the integral arrangement is the more compact choice [S1][S7].