A listed 2 t steel foundry ladle is priced at ₹50,000, while published offers for bottom-pouring and treatment equipment extend across 0.2–20 t [S1][S5].
Foundry ladles are specified by molten-metal working capacity rather than shell dimensions, with crane-mounted units serving foundries from 100 kg upward and steel-mill ladles extending to 300 t [S2].
Price Benchmarks Across Ladle Capacity
One public listing gives a 2 t steel foundry ladle a price of ₹50,000. The stated dimensions are 30 inches in diameter and 4 feet high, with a 12-month warranty, 220 V electrical rating, and a steel shell [S1].
For comparison, Neelkamal Engineers lists a bottom-pouring ladle at approximately ₹92,000 per piece, covering capacities from 200 kg to 20 t [S5]. Its pouring and treatment ladle starts at approximately ₹48,000 per piece [S5].
These figures are listing prices, not universal price-per-ton tariffs. The ₹25,000 nominal difference per ton between the ₹50,000 2 t ladle and ₹92,000 0.2–20 t bottom-pouring offer does not establish a valid capacity curve because the latter covers a wide range and includes a different discharge mechanism [S1][S5].
Why Capacity Alone Does Not Set the Price
Working capacity is the primary commercial basis for foundry ladle selection, but capacity does not determine price by itself. The same 2 t class can include an open lip-pouring vessel, a closed treatment ladle, or a bottom-pouring unit with a stopper mechanism [S1][S5].
Configuration affects the materials and controls that must be quoted. The bottom-pouring ladle is described as providing slag-free metal for pouring both light and heavy work [S5].
Refractory construction is another cost boundary. Steel or iron shells for ferrous work are normally lined with refractory to preserve heat and protect the vessel from direct contact with molten metal; non-ferrous operations may use ceramic, graphite, or coated-steel hand and robotic ladles [S2][S4].
Foundry operators can compare lining alternatives in Castable vs Preformed Insert Lining for Foundry Ladles. This distinction matters because the quoted price must define what is supplied, rather than leave refractory construction as an unpriced assumption.
Capacity Bands and Physical Sizing

Published capacity bands span four practical procurement segments: 100–200 kg units, 0.5–2 t work ladles, 2–10 t treatment or transfer equipment, and units extending to 20 t for heavy pouring duties [S1][S5]. These bands are more useful for an initial budget than a diameter-only comparison because shell size does not establish usable molten-metal capacity [S2].
A 500 kg pouring-capacity foundry ladle is also listed under a 0–2 t product class, using pendant control and lip pouring [S6]. By contrast, the 2 t listing uses a 30-inch diameter, 4-foot height, open steel shell, single-phase 220 V supply, and 50–60 Hz frequency [S1].
The used-foundry-ladles category page on Surplus Record showed 18 results [S3]. The listing requested a price rather than publishing one, so it cannot support a numerical used-ladle price comparison [S3].
Lip Pour, Bottom Pour, and Treatment Comparison
A 2 t steel foundry ladle with an open shell is listed at ₹50,000 for metal pouring [S1].
Bottom-pouring ladles trade simpler construction for controlled discharge and slag separation. The bottom-pouring ladle is approximately ₹92,000 per piece, has a capacity of 200 kg to 20 t, and is applicable to both light and heavy work [S5].
The manufacturer offers pouring and treatment ladles, as well as SG-iron and ductile-iron treatment ladles, including a teapot-spout ladle [S5].
Cost Drivers Beyond the Purchase Price

The purchase price is only one line in the total cost. Shell steel, refractory lining, gear or stopper hardware, heating, handling, maintenance, and operating time can outweigh the initial capacity-based comparison [S1][S2][S5].
Capacity normally raises material use, but the research does not provide a linear price-per-ton relationship. The listed prices support only three direct benchmarks: ₹50,000 for a 2 t steel ladle, approximately ₹92,000 for a 0.2–20 t bottom-pouring model, and approximately ₹48,000 for a 100 kg–10 t treatment-ladle family [S1][S5].
Installation and handling also affect ownership cost. Small units may be moved by hand, while larger steel vessels use a lifting bail, overhead crane or monorail, gearbox, or dedicated transfer arrangement; very large ladles may run on wheels, a transfer car, or two lifting devices [S2].
Refractory condition influences service life and downtime. The lower-cost shell is not the operating asset if the lining fails early, so a supplier quote should state lining material, shell thickness, service temperature, relining scope, and expected maintenance access. Lining selection is also relevant when comparing a crucible furnace, because the melting vessel and the transport or pouring vessel have different thermal duties.
Application Fit and Sourcing Checklist
A foundry ladle is suitable when the required pour weight, metal temperature, transfer route, and discharge method match the vessel. Large steel-mill ladles can hold up to 300 t, but that scale is outside the 20 t upper bound of the published bottom-pouring offer [S2][S5].
The specification should include working capacity in kilograms or tons, molten-metal temperature range, shell material, refractory lining, shell opening, pour method, operating mechanism, lifting arrangement, shell dimensions, warranty, and delivery scope. A 30-inch diameter and 4-foot height are useful envelope data for a 2 t unit, but they do not replace working capacity as the sizing basis [S1][S2].
Foundries using treatment or transfer duties should also specify slag control, metering accuracy, treatment recovery, and maintenance access. Neelkamal describes heavy-duty transfer equipment for working capacities from 100 kg to 20,000 kg and lists transfer options at 0–2 t, 2–4 t, and 4–6 t [S5].
The defensible procurement method is to request like-for-like quotes by capacity band and pouring architecture, then separate the shell, refractory, drive mechanism, crane interface, commissioning, and annual maintenance. Track the quoted tonnage, working-versus-geometric capacity, lining specification, and delivered price in each comparison. If a supplier cannot state the basis of its ₹ per ton figure, the number is a marketing ratio, not an engineering estimate.