REQUEST FOR QUOTE → Request a quote
SpecForge Editorial Team

Permanent Mold Casting Draft Angle Requirements

Table of Contents
  1. What Draft Angle Means in Permanent Mold Casting
  2. Selection Criteria for Draft and Parting-Line Design
  3. Draft Requirements by Casting Process
  4. Who Should Specify Draft and When
  5. Failure Modes and Manufacturing Constraints
  6. Drawing Requirements and Sourcing Checks
Permanent Mold Casting Draft Angle Requirements

Permanent-mold guidance indicates that exterior draft in the direction of metal flow may vary from 1° to more than 10°, while internal draft begins at a slight angle.

Draft should be considered on exterior walls and internal cores that must release from a reusable metal mold, because zero draft can increase friction or interference and cause parts to be stripped, dented, or stuck.

What Draft Angle Means in Permanent Mold Casting

Draft is the taper applied to a casting wall relative to the mold-withdrawal direction to provide clearance for ejection. A wall perpendicular to the mold-withdrawal direction can create friction or interference that prevents the part from releasing and may damage the mold or casting.

Published permanent mold guidance places exterior draft in the direction of metal flow at 1° to more than 10°, with internal draft beginning at a slight angle [S6]. That wider range reflects geometry, withdrawal direction, surface finish, and mold condition rather than a single universal draft value [S6]. Draft on cores and internal features must be evaluated separately from outside walls.

Injection-molding draft is measured from the vertical axis of the mold and helps account for thermoplastic shrinkage. That plastic-process rule is not a permanent mold requirement, but it demonstrates why depth, shrinkage, and friction must be considered during mold design.

Selection Criteria for Draft and Parting-Line Design

Parting-line placement is the first draft decision because the line determines which surfaces can withdraw directly from each die half [S1]. A suitable line can eliminate undercuts and reduce the number of gates and risers required, supporting a stronger casting with less wasted material [S1].

Then assess each wall against three criteria: its angle to the withdrawal direction, the depth over which it remains engaged, and its sensitivity to surface damage. LA Aluminum identifies SOLIDWORKS as its preferred CAD program and notes that the simplest way to determine parting-line placement is to use the program's built-in tools.

Wall thickness and machining allowance also affect the practical choice. A 3° draft over a 10-inch-deep wall produces a total width change of about 0.524 inches across the depth, or about 0.262 inches per side.

Draft Requirements by Casting Process

draft angle requirements for permanent mold castings - Draft Requirements by Casting Process
draft angle requirements for permanent mold castings - Draft Requirements by Casting Process

Permanent-mold guidance indicates that exterior draft in the direction of metal flow may vary from 1° to more than 10°, while internal draft begins at a slight angle. This differs from V-Process, where the vacuum-held loose sand separates without normal pattern friction, allowing castings with zero-degree draft [S2].

Zero draft is therefore not a general casting allowance. It is available in V-Process without draft because the filmed pattern creates a barrier against the loose sand [S2]. In conventional permanent mold tooling, the relevant comparison is not whether zero draft can exist geometrically, but whether the casting and mold can separate without scuffing, dents, seizure, or die wear [S4].

Who Should Specify Draft and When

Product engineers, casting engineers, mold makers, and machining planners need draft information before CAD release because draft changes the nominal wall position, parting-line strategy, gate and riser requirements, and machining allowance [S1][S2]. A drawing note added after tooling has been cut cannot correct a geometric under-cut without modifying the die.

This specification is for permanent mold and other rigid-tool die-cast parts where the casting must physically withdraw from steel tooling. It is not the controlling rule for V-Process or for injection-molded polymers. It is also unsuitable for designs that require zero draft on all walls without reviewing the ejection process and casting surface requirements [S2][S4].

For parts with no functional requirement for a perfectly vertical wall, redesigning it with 5° or more is generally less costly than adding draft stock, machining the taper away, introducing a core, or modifying the parting line after production begins [S1][S2]. A permanent mold casting drawing should therefore state draft per side, the parting line, withdrawal direction, and permitted undercuts together.

Failure Modes and Manufacturing Constraints

draft angle requirements for permanent mold castings - Failure Modes and Manufacturing Constraints
draft angle requirements for permanent mold castings - Failure Modes and Manufacturing Constraints

Insufficient draft causes the casting to drag against the mold, which can damage the part, impair ejection, and reduce tool life [S1][S4]. The failure becomes more likely as an unsupported wall becomes deeper, as the surface becomes rougher, or as a core traps the casting between closed die halves. Permanent-mold guidance presents exterior draft as a variable range from 1° to more than 10°, rather than establishing a single universal target.

Undercuts are a separate problem. A wall that is parallel to withdrawal can bind, while a re-entrant feature can lock the casting inside the tool. Parting-line adjustment may remove the undercut, while fillets and rounds on flat surfaces can improve removal and reduce stress concentration [S1]. The draft itself must not conceal an impossible parting condition.

Surface condition also affects release. Machined, smooth surfaces can release more easily than profiles contaminated by paint buildup or hand-finishing swales, and deeper parts need more draft because the contacting area and frictional load increase [S3]. Published pattern experience cites about 1° as sufficient for clean, smooth releases, 2° for accurately machined production geometry, 3° per side as a practical deep-part choice, and 5–7° as a conservative range [S3].

Drawing Requirements and Sourcing Checks

A permanent mold casting drawing should identify draft as degrees per side, define its reference to the parting plane, and show the core draft separately. It should also locate machined surfaces, specify up to 0.030 inches of stock where cleanup is planned, and identify any feature permitted to remain vertical only after a process review [S1].

The sourcing check has four steps. First, compare exterior and internal walls against the 2–3° minimum and 5° preferred target [S1]. Second, verify that the proposed parting line cannot create undercuts [S1]. Third, check whether the component requires a zero-draft feature that justifies a different casting route [S2][S4]. Fourth, confirm wall thickness and machining allowance before pricing the die casting die or permanent mold tooling.

For production execution, use CAD parting-line and undercut analysis, compare the released model with the tool maker's draft interpretation, and inspect a sample for drag marks or tool witness lines. If a vertical feature is mandatory, document it explicitly instead of treating it as an implied casting tolerance [S1][S4].

The next trackable signal is the released casting drawing: its parting line, per-side draft callout, internal draft, and machining stock should agree with the permanent mold tooling model before the first metal is poured.

Frequently asked questions

What minimum draft angle should be specified for permanent mold castings?

Permanent-mold guidance indicates that exterior draft in the direction of metal flow may vary from 1° to more than 10°, while internal draft begins at a slight angle.

Does draft need to be specified separately for internal cores and exterior walls?

Yes. Draft on cores and internal features must be evaluated separately from exterior walls because both must release from reusable metal tooling. Zero draft is normally avoided because it increases friction, deformation, and tooling damage.

When should parting-line and undercut analysis be completed before CAD release?

Complete parting-line and undercut analysis in CAD before releasing the model and before tooling is cut. The parting line determines which surfaces can withdraw directly from each die half, and an apparently open feature may still become an undercut in the corresponding mold cavity.

How should draft affect nominal dimensions and machining stock?

A 3° draft over a 10-inch-deep wall produces a total width change of about 0.524 inches across the depth, or about 0.262 inches per side.

6 sources
  1. Casting Design Improvement for Permanent Mold
  2. Why is draft not necessary in V-Process? (Mar 11, 2020)
  3. Patern draft angle
  4. Die Casting with Zero Draft Angles (Nov 15, 2024)
  5. Injection Molding Draft Angle Guide
  6. A Primer on Permanent Mold Casting (Dec 1, 2025)

Need to source matching manufacturers or get a quote?

SpecForge connects industrial buyers with verified manufacturers. Submit your requirement and we will route it to matched suppliers.

Submit RFQ now →
Ask SpecForge AI