A tilting gravity die casting machine may be considered for an aerospace bracket because gravity die casting produces dense, heat-treatable aluminium castings, but the source warns that a T6 heat-treated batch can blister from trapped gas [S2][S3].
Specify the machine around bracket mass, projected area, mold weight, pour temperature, clamping force, ejection force, and annual volume rather than generic tonnage alone [S1][S3].
Gravity casting conditions for a load-bearing aerospace bracket
Aluminum gravity casting fills a reusable steel or iron mold without an injection plunger, using only the head of the pouring basin to move molten metal [S1][S2]. The permanent die is preheated, coated with refractory release material, filled, solidified, opened, and ejected before trimming and optional T6 heat treatment [S2].
This route fits a heat-treatable aluminum bracket with a moderate annual demand. Gravity casting can produce dense castings, accepts sand cores for internal passages, and generally costs less in tooling than pressure die casting, but its slower cycle makes it less attractive when annual volume is large [S1][S3].
For an aerospace application, define the approved material, temper, casting specification, inspection method, allowable porosity, traceability requirements, and machining allowance before releasing the permanent die. Gravity casting alone does not establish aerospace compliance.
Tilting, static, and servo-controlled machine types
A tilting machine is preferable where smooth metal entry and repeatable fill matter because the mold rotates from horizontal toward vertical, allowing metal to travel along the cavity wall rather than fall turbulently into it [S3]. Static pouring can work for simple geometries, but it leaves fill behavior more dependent on ladling technique and pouring height [S2].
Servo-controlled tilting is justified where the bracket requires programmable pour profiles. The documented servo tilt provides a programmable fill profile, and the identified tilting machines are FMU1 and FMU2 [S3]. These are example machine capabilities, not universal limits.
Tilting gravity die casting models use servo-driven mechanisms and hydraulic clamping for repeatable cycles [S1]. For a comparison of gravity-casting output against HPDC, see Gravity Die Casting vs HPDC Cycle Time and Output.
Machine sizing by bracket geometry and die loads

Start with the finished casting weight and calculate the metal charge, runner, gating, and riser volume before selecting the tilting table or pouring capacity. Then verify static and dynamic loads from the mold, metal head, core supports, and moving table. A quoted machine capacity cannot be accepted without the maximum mold dimensions and allowable center-of-gravity offset. [S2]
For clamping and ejection, the die casting die must fit within the platen and stroke envelope without the bracket being distorted. Calculate ejection force from casting mass, die draft, shrinkage allowance, and any local shrinkage around bosses or ribs. The Die Casting Ejector Stroke and Force Rating Guide provides a separate framework for checking that mechanical capacity.
Use the gravity die casting machine specification sheet to close the cycle: mold open, core set, tilt to fill, hold or return, solidify, open, eject, and reset.
Alloy and heat-treatment selection
A356 in the T6 condition is the baseline candidate because it combines structural strength, ductility, and heat-treatability. A319 is another gravity-castable option where some hot-cracking sensitivity can be accepted, while 6061 is relevant where weldability is a priority [S2].
T6 treatment requires control of cast porosity, trapped gas, cooling, and section thickness. Gravity die casting can produce less porous components with higher density and superior strength than pressure die casting [S5]. This is a process advantage, not a substitute for radiography, pressure testing, or other part-specific acceptance methods.
For a detailed component comparison, the aluminum die casting machine page covers machine configurations intended for aluminum production, while the casting route must still match the bracket’s wall thickness, thermal mass, and production volume.
Heat treatment, tooling temperature, and process control

In aluminium gravity casting, molten aluminium is poured into a reusable steel or iron die whose mold is preheated and coated before gravity fills the cavity from the top basin [S2]. The applicable band depends on the alloy, coating, geometry, and trial results, so the purchase specification should control temperature by zone rather than state one unverified setpoint.
Pour temperature must be tied to the alloy specification and controlled through calibrated instruments. Fill rate follows pouring head and gate design rather than a fixed machine cycle [S2]. During thermal processing, use the material supplier’s approved treatment cycle; the research supports T6 as a relevant condition for A356 but does not establish a universal aerospace heat-treatment schedule.
Gate and riser placement determine whether shrinkage is drawn toward the feeder rather than the bracket wall [S2]. Review both before ordering tooling, because adding or relocating a riser can change mold size, tilting load, thermal balance, and machine-capacity requirements.
Gravity casting compared with LPDC, HPDC, and sand casting
Gravity die casting is the preferred route when the bracket is aluminum, must reach T6 properties, contains sand-core passages, and runs at a volume where permanent tooling is justified but HPDC economics are not [S2][S3]. Low-pressure die casting also provides a calm, dense, heat-treatable result, but it requires a die above a sealed furnace and a higher machine investment [S3].
Do not select HPDC solely because it has a shorter cycle, and do not reject gravity casting solely because its cycle is slower. The decision hinges on the required annual volume, wall thickness, heat treatment, core geometry, porosity acceptance, and total machined-part cost [S1][S3][S5].
Where gravity casting should not be selected

Reject the mainstream gravity route when the program requires very thin walls, rapid fill of intricate features, or very high output. HPDC fills detailed and thin-walled features more effectively and is generally better suited to high-volume production [S5]. Do not select gravity casting when the required geometry cannot be extracted reliably from the permanent die or when risers and cores cannot be placed without creating unacceptable local mass or machining cost.
Avoid a fixed-capacity purchase before the bracket drawing, alloy, pour mass, runner system, riser, core concept, and expected production volume are frozen. Early machine selection should establish an envelope, but final rating requires the finished tooling package. The die casting machine reference is useful for comparing machine classes, but it cannot replace die-specific load and capacity calculations.
Purchase specification and acceptance tests
Issue the request for quotation with eight mandatory items: finished-part mass, maximum mold mass, mold dimensions, pour-metal mass, annual demand, alloy and temper, required cycle target, and inspection acceptance criteria. Add the allowable pour-temperature range, mold-temperature zones, core details, pouring method, automation boundary, and machining allowance [S1][S2][S3].
The supplier should demonstrate mold preheat and coating, controlled tilt angle and speed, repeatable pour quantity, closed-cycle ejection, and PLC sequence control [S1]. Request a cycle-time study with the production die and representative bracket, because a documented 240-part-per-shift figure was measured for cylinder heads, not aerospace brackets [S3].
For process qualification, use representative castings to establish fill, solidification, riser feeding, trimming, heat treatment, dimensional accuracy, and inspection results. Track melt chemistry, pouring temperature, mold-temperature profile, cycle time, rework, scrap, and inspection rejects. Require the aerospace supplier to provide applicable material and casting standards in the purchase document, but do not infer flight-critical approval from the machine model or the gravity process alone.
Shortlist a servo tilting machine only when its rated mold size, mold weight, tilt range, tilt accuracy, pouring capacity, clamping force, ejector stroke, and ejector force cover the fully developed die with engineering margin. The decisive trial is a representative bracket run, not a general machine specification sheet.