Double-row ball spline nuts use four to six ball rows to support higher loads and moment loads than single-row configurations, while preloaded designs can eliminate angular backlash.
The choice depends on shaft diameter, torque, moment loading, required accuracy, recirculating-path geometry, and acceptable envelope rather than row count alone.
What Single-Row and Double-Row Ball Spline Circuits Do
A ball spline combines a grooved shaft, a spline nut, and steel balls to provide linear motion while transmitting torsional loads. The grooves guide the balls along the shaft, and the nut raceways retain and recirculate them [S4][S9].
A single-row arrangement has one row of balls at each relevant spline contact and is generally associated with lighter-duty service. Double-row arrangements place two rows on either side of a crest, producing four to six rows in total depending on shaft geometry. THK specifies a nominal shaft diameter of 25–60 mm for the high-torque SLS/SLS-LN series [S5].
The decisive distinction is load sharing. Double-row bearings generally accommodate heavier radial and axial loads than single-row bearings [S2][S8]. For ball splines, the equivalent benefit appears as greater resistance to moment loading and higher torque capacity, but the manufacturer’s rating for the selected diameter and nut length remains the controlling design value [S3][S5].
Compare Single and Double Rows Against Engineering Criteria
Single-row circuits are appropriate when the application is lightly loaded, cost is the priority, and the shaft requires only one compact nut. Double-row circuits suit heavier loads, higher reliability demands, and applications where torsional and moment stiffness matter [S2]. The four-groove configuration can place active and recirculating paths side by side, reducing nut length, while a six-groove shaft may require the nut to project beyond the shaft to provide recirculation space [S3].
Single-row is not a universal low-cost substitute for double-row. If the axis must transmit substantial torque while resisting overturning moment, the extra rows can reduce ball loading and preserve stiffness. If load is modest, a heavier arrangement may add envelope, cost, and assembly constraints without producing a useful performance gain.
Recirculating Path Layout Controls Nut Size

The ball path is not merely a row count. A recirculating circuit must return each ball from the loaded side to the unloaded side, and the return route requires space outside the active raceway. In a four-groove ball spline, side-by-side active and recirculating paths produce a compact nut; a six-groove system can consume enough shaft space that the nut must protrude beyond the shaft for ball return [S3].
This makes internal path geometry a first-order selection check. Verify the manufacturer’s longitudinal section, nut outside diameter, shaft projection, minimum installation length, and mounting orientation before choosing a row count. A crossed-roller guide may be preferable when the requirement is moment capacity without the spline’s rotary function, but it does not replace a ball spline’s combined torque transfer and linear guidance.
Preload, Accuracy, and Contact Geometry
The LT design uses appropriate preload to eliminate angular backlash [S5]. THK describes angular-contact ball contacts in its LBS design as allowing preload to be applied evenly, while the LT design specifies a 20° contact angle with an appropriate preload level [S5].
Groove contact form also affects rigidity and repeatability. A four-point Gothic-arch profile is associated with zero clearance, greater moment-load capacity, and higher rigidity, while conventional two-point contact is the alternative geometry described in the ball-spline specification literature [S3]. Thomson precision ball splines provide a low-friction path and enable the transmission of torsional loads [S4].
For a new axis, request the rated load, rated torque, allowable moment, preload method, angular-clearance specification, and repeatability data for the exact shaft diameter and nut length. Do not infer these values from row count alone. The same diameter can have different ratings when nut length, raceway geometry, shaft rigidity, and mounting differ [S3][S5].
Matched Applications and Selection Rules

THK lists applications for the SLS/SLF high-torque caged-ball series that include robot columns and arms, automatic loaders, transfer machines, welding-machine spindles, riveting machines, wire winders, and grinders [S5]. These applications combine torque, moment loading, and repeated positioning rather than simple straight-line transport.
Single-row circuits fit light-duty handling slides, auxiliary shafts, positioning fixtures, and applications where the shaft only needs moderate torque and low cost. A ball spline differs from a plain keyed shaft because its grooved shaft and circulating balls support both linear travel and torsional load transfer [S4][S9].
Use double row when any of these conditions apply: peak moment load is high, the nut has a short mounting length, torque must be held with low angular backlash, or operation involves impacts, vibration, and high-speed linear motion. Use single row when loads remain within the lower-duty range, the envelope is restricted, and the required accuracy can be met without a multi-row circuit. The THK SLS and SLF high-torque caged-ball types, covering nominal shaft diameters of 25–60 mm, use cage-controlled circulation to reduce ball collision, particle generation, and rolling fluctuation [S5].
Installation, Maintenance, and Failure Limits
Ball splines require adequate housing support and correct shaft alignment because nut or housing misalignment creates moment loads and uneven ball contact. THK identifies shaft rigidity and mounting system as two of the seven factors that can increase ball-spline load capacity, alongside groove count, groove shape, and nut or raceway length [S3].
Retainers keep the balls from falling out of the nut and support smooth circulation [S6]. A removable, ball-retaining nut design facilitates maintenance, while caged-ball models use a cage to maintain even ball spacing [S4][S5]. Lubrication remains a design requirement; caged-ball construction can improve grease retention, but the operating environment, cycle rate, and contamination level still determine lubrication and inspection intervals [S5].
Compare a ball spline with a keyed shaft using the selection guide for ball splines over keyed shafts. Before release, document the selected row count, shaft and nut model codes, contact angle, preload, allowable moment, grease specification, and the requirement to prevent shaft withdrawal with the nut removed [S3][S5][S6].