Hex and spline demolition bits are not interchangeable because their shank geometry and locking mechanisms differ.
SDS-Plus has a nominal 10 mm shank with two open drive grooves and two closed retention grooves, while SDS-Max has a nominal 18 mm shank with three open drive grooves and two closed retention grooves and is not interchangeable with spline drive.
Compatibility at a glance
A demolition hex shank is identified by its across-flat size, collar and retention geometry, not by the generic term “hex.” SDS-Plus has a nominal 10 mm shank with two open drive grooves and two closed retention grooves; SDS-Max has a nominal 18 mm shank with three open drive grooves and two closed retention grooves [S3].
Spline shanks have longitudinal splines that engage a matching collar inside the holder. Hex shanks transmit torque through flat faces, while SDS systems transmit rotation through keyed or slotted grooves and permit axial travel during hammering [S1][S2]. These are different mechanical interfaces, so a hex bit cannot be forced into a spline chuck, or a spline bit into an SDS-Max chuck.
SDS-Plus has a nominal 10 mm shank, while spline drive and SDS-Max use different, non-interchangeable shank geometries. SDS-Max and spline tools can both serve heavy demolition work, but selection begins with the installed machine, not the proposed accessory [S1].
How hex and spline interfaces transmit load
Hex shanks provide high torque transmission without relying on clamping pressure alone, because the holder engages the shank's flat surfaces mechanically [S2]. That makes hex suitable for sustained torque applications where a round shank might slip under load [S5].
Spline drive also locks mechanically. Longitudinal splines mesh with the holder's internal collar, providing rotational drive while allowing the axial float required by the hammer cycle [S1]. This interface is used with compatible rotary hammers and demolition chisels, including spline-shank bits intended for breakers [S6].
SDS shanks use a different arrangement. The bit slides axially as the striker acts, while matching longitudinal grooves maintain rotational drive and closed retention grooves keep the accessory from dropping out [S3]. A properly latched SDS bit can therefore move slightly under impact; that movement is intentional, not a sign of a loose holder.
Decision matrix for demolition tools

Hex versus spline selection has four practical criteria: holder fit, torque transfer, axial hammer movement and accessory availability. The decisive criterion is holder fit because none of the other three matters when the shank cannot enter or lock correctly. [S3]
Hex is the rational choice when the breaker specifies a hex across-flats size and retention collar. Spline is the rational choice for a machine with a matching spline collar. SDS-Plus and SDS-Max apply to their respective machines rather than to a hex or spline breaker merely because the accessory performs a similar task.
Matching bits to the installed machine
Read the holder marking and manufacturer accessory list before ordering.
For a hex breaker, confirm the across-flats dimension, collar position, retention feature and accessory part number. For a spline breaker, confirm the spline pattern and holder family rather than accepting a generic “spline” label. The shank, cutting diameter, carbide construction and joining method are separate specifications [S3].
Tool geometry should then match the work. A moil point concentrates force into a small area for initiating hard-concrete breaks, while a flat chisel removes more material after a break has started [S1]. For deeper holes, the difference between SDS-Plus and SDS-Max becomes relevant, as covered in SDS-Plus vs SDS-Max rotary hammer selection.
Application fit and common failure modes

Hex and spline systems can both handle serious concrete-breaking work when the machine, bit and chisel geometry are matched [S1]. The shank type does not alone determine breaking speed. Chisel geometry has a greater influence on performance in hard aggregate, with a moil point for initial penetration and a flat chisel for controlled material removal [S1].
Using the wrong shank creates three principal risks: the bit may not seat, the retaining features may not engage, or rotation and impact may be transferred incorrectly. A forced fit can damage the chuck, the shank or both. Do not treat a loose axial slide as evidence that the correct interface is present, because SDS-style movement is controlled by the holder's design [S1][S3].
Adapters and generic substitutions are poor substitutes for matching heavy-duty equipment. Custom-engineered connections are preferable for continuous or high-load service because adapters introduce additional interfaces and their own limits [S5]. If a hire company supplied the breaker, specify its exact model and obtain the approved shank family before procurement.
Material and wear checks before installation
Shank compatibility does not establish the bit's steel grade or cutting capability. For one-piece steel-body SDS bits, the shank and fluted body share the specified steel grade, while the carbide head is a separate material. That rule does not automatically apply to assembled or welded-body designs.
A cemented carbide cutting tip is separate from the alloy-steel body. A designation such as “carbide head” does not identify the carbide grade, cutter count or brazing construction, so those details must be confirmed against the selected model [S3]. Likewise, hex or spline compatibility alone does not prove suitability for hardened steel, reinforcement or high-cycle demolition.
Inspect the shank, grooves, flats, collar and retention areas before insertion. Reject a bit with deformation, impact marks, rounded splines, damaged flats or a retaining feature that no longer matches the holder. The relevant machine-side comparison for power-tool classes is covered in the SDS-Max rotary hammer reference, but the manufacturer's final compatibility list remains controlling.
Procurement rule for mixed fleets

A demolition contractor operating both hex and spline breakers should label holders by exact interface and maintain separate accessory bins rather than grouping everything as “hammer bits.” Record the machine model, shank family, nominal shank size, across-flats dimension where applicable, and approved part number for every stocked bit [S2][S3].
When a fleet includes hex, spline and SDS-Max platforms, standardize procurement by machine rather than by appearance. Fit verification requires the actual holder and bit in hand: an 18 mm SDS-Max shank does not prove spline compatibility, and a splined shank does not prove SDS-Max compatibility. The next trackable control is a 100% receiving inspection against the approved machine-to-accessory list, with rejected or unverified stock quarantined.