For aluminum cutting, blades typically range from 24 to 120 teeth, depending on material thickness, machine speed, and the required finish.
Blade speed and geometry must match the workpiece: aluminum favors higher speed, controlled feed, and chip control, while steel requires slower cutting and teeth designed to withstand greater heat and load [S1][S2].
Tooth Count and Material Thickness
Cold-saw tooth count is the number of cutting teeth around the circumference, while tooth pitch is the distance between teeth; these are related but not interchangeable [S7]. Blades made for aluminum help keep the work area cool and remove chips cleanly.
Aluminum blades span approximately 24–120 teeth across the available range, with the choice governed by material thickness, cutting-machine speed, and required finish [S6].
Steel Versus Aluminum: Blade Requirements
The Blade Manufacturing Co. tooth-selection chart recommends increasing the tooth count by 20% for stainless steel and hard alloy steel relative to the baseline for tougher steels.
Aluminum is a soft, non-ferrous metal that tends to gum and stick in the blade, whereas steel is ferrous and creates greater heat and friction [S1][S2]. The practical comparison is therefore not tooth count alone:
For aluminum cutting, blades typically range from 24 to 120 teeth, depending on material thickness, machine speed, and the required finish.
Blade Material and Cutting Speed
HSS and tungsten-carbide-tipped blades are the two principal cold-saw blade types, with TCT permitted to run somewhat faster than HSS [S4]. Standard M2 HSS aluminum blades can clog, overheat, or leave a rough cut, while carbide-tipped aluminum blades retain their edge at higher speed and are less prone to gumming [S1].
Material choice also depends on machine speed. HSS is the practical choice when a saw operates at low RPM, whereas carbide can cut aluminum and steel at higher speeds and offers greater durability [S2].
Aluminum should generally run at higher RPM than steel because aluminum conducts heat rapidly; steel normally needs a slower approach to control heat and friction [S1][S2]. HSS remains suitable for steel studs, bars, and sheets, but a blade designed only for mild steel should not be transferred to stainless or alloyed steel [S2].
Geometry, Coolant, and Failure Modes
Standard M2 HSS blades often struggle with aluminum by clogging, overheating, or leaving rough edges.
Wrong blade or tool settings can cause clogging, overheating, rough edges, catching, and waste when cutting aluminum.
Blade diameter, arbor, body thickness, and permitted operating speed therefore remain mandatory checks before comparing tooth counts.
Decision Matrix by Workload
For thick aluminum, select 60–80 teeth with negative rake or negative hook geometry and controlled coolant [S1].
For aluminum, control the feed and use an appropriate RPM setting to prevent the blade from rubbing. For stainless or alloy steel, confirm that the blade grade is rated for that material and follow the tougher-steel baseline in the tooth-selection chart [S7].
A comparison of bench-mounted and portable cut-off machines is useful only after blade speed, workholding, and material geometry are fixed.
Sourcing and Cutting Record
Specify tooth count, pitch, tooth height, blade material, diameter, arbor, body thickness, grade, coolant, permitted RPM, workpiece material, thickness, and required cut finish. The cold-saw reference describes solid high-speed-steel blades as mainly M2 or M35, while the aluminum-selection guidance specifically flags standard M2 HSS blades as vulnerable to clogging and overheating [S1][S4].
Keep separate blades for aluminum, mild steel, stainless steel, and alloy steel rather than treating them as interchangeable. One shop reported maintaining four or five sharpened blades in rotation, but that operating practice does not replace a material-specific tooth recommendation [S5]. Record cuts by material and thickness, then track heat at the blade, edge condition, chip evacuation, and downstream machining allowance.
For the next procurement or setup, record the actual machine RPM, blade diameter, arbor, material grade, section dimensions, and whether the cut is a blank or finish cut, then match those five inputs to a manufacturer tooth chart before ordering [S3][S7].