Desalination electric actuators must match valve motion and load first, then withstand salt-laden service, infrequent operation, and the plant electrical and safety requirements [S1][S2].
Quarter-turn units suit butterfly, ball, and plug valves;
Start with valve motion and operating load
Valve size is not an adequate sizing parameter. Determine rated output torque for rotary valves or rated thrust for linear valves, then apply the manufacturer’s service factors rather than selecting from nominal valve dimensions alone [S2]. Published water-service families include quarter-turn electric actuators rated from 100 to 27,300 in-lb torque and spring-return electric actuators rated from 200 to 1,200 in-lb torque [S7].
That range must be compared with valve stem area, fluid differential pressure, packing friction, and the minimum opening force. A unit that can complete the stroke under maximum differential pressure may still lack margin for worn packing or elevated seawater temperature.
Compare quarter-turn, multi-turn, and linear options
Quarter-turn actuators are the normal choice for butterfly, ball, and plug valves because their normal travel is about 90 degrees [S2]. Their selection remains unresolved by travel alone: torque, speed, mounting, power supply, feedback, and environmental ratings determine the final model [S2].
Electric actuation provides precise positioning, repeatable motion, electronic feedback, and self-diagnostics, but it has less raw force capability than hydraulics and generally carries a higher initial cost and greater mechanical complexity [S5]. Hydraulics suit exceptionally heavy-duty motion, while pneumatic systems require compressed air and can suffer from pressure loss, moisture, and oil contamination [S5]. For normal desalination valve automation with plant power available, electric actuation usually offers the cleaner control architecture.
Size for seawater, pressure, and infrequent travel

Desalination duty demands an actuator sized for the worst credible operating condition, not merely nominal clean-water flow. The actuator should cover maximum valve differential pressure, high seawater temperature, chloride exposure, and friction from the selected valve material and trim [S1][S4].
Water and wastewater actuators must remain reliable even when operation is infrequent [S1]. This makes gearbox backlash, drive-train seizure, motor thermal protection, and local mechanical position indication more important than headline cycle speed. Verify that the actuator can produce the required output after long standby periods and that its wetted or externally exposed metal parts are suitable for the specified corrosion class.
Published product offerings for desalination service include quarter-turn, multi-turn, IP67 explosion-proof, IP68 waterproof, and ATEX-oriented electric actuator configurations [S4]. IP67 and IP68 are distinct ingress designations, while explosion-proof and ATEX requirements address hazardous-area duties. They should not be treated as interchangeable corrosion or certification statements [S4].
Match controls, power, and safety functions
The control architecture must match the desalination plant’s electrical supply and automation strategy. Selection inputs include the control method, available power, feedback requirements, and safety functions [S2]. Electric actuators commonly support electronic positioning, velocity control, feedback, and diagnostics [S5], but the procurement specification must name the required protocol, signal resolution, response time, and failure position.
Specify whether the unit needs on-off operation, proportional positioning, or a fail-safe action on loss of power or control signal. Spring-return electric products are available for water and wastewater duties at 200–1,200 in-lb torque [S7]. A spring-return requirement should therefore be treated as a functional option, not assumed from the motor type.
The selection matrix should list valve tag, valve type, motion, rated torque or thrust, maximum differential pressure, fluid temperature, actuator speed, supply voltage and frequency, control signal, feedback devices, ingress rating, hazardous-area classification, fail position, mounting orientation, and required accessories [S2]. This makes model review possible instead of relying on a generic actuator family.
Set environmental and installation limits

Actuator mounting must match the valve stem or shaft interface and the permitted spatial envelope. Before finalizing the model, check mounting, environmental exposure, and maintenance access [S2]. A compact actuator is useful where space is restricted, but installation clearances must still permit motor replacement, cable entry, manual operation, and periodic inspection.
For exposed desalination areas, require a documented enclosure rating and corrosion-compatible external materials. IP67 addresses protection against dust and temporary immersion, while IP68 addresses continuous immersion under the manufacturer’s defined conditions [S4]. Neither code alone establishes resistance to chloride attack, so the materials specification must separately identify the housing, exposed fasteners, shaft, and coating system [S4].
Electric actuation avoids hydraulic fluid and compressed air at the mechanism [S5], reducing fluid leakage and simplifying clean service. It does not remove the need for environmental control: salt deposits, condensation, direct solar exposure, washdown, and standing water can affect seals, terminal boxes, connectors, and the motor frame.
Choose the right actuator for the service boundary
An electric actuator is a strong fit for electrically actuated isolation and control valves where precise travel, remote feedback, and low routine fluid use matter [S5]. It is not automatically the right choice for very high-force service where hydraulic output is more appropriate, nor for a duty whose process safety case requires a pneumatic concept [S5].
Electric operators should not be selected for a steam-trace or auxiliary equipment duty merely because the valve is electrically automated. If the actuator belongs to the steam system, its operating environment and function differ from the principal desalination fluid circuit; the applicable engineering boundary should be established before applying valve-actuation criteria.
Do not use a standard weather-resistant actuator as an unverified solution for a submerged or hazardous location. Require the supplier to identify the applicable ingress or hazardous-area certification, the certificate basis, the permitted temperature class, and the corrosion construction shown on the datasheet [S4].
Verify the selection before purchase

The purchasing file should contain the valve manufacturer’s maximum torque or thrust requirement, the calculated actuator output, the selected motor voltage, the control signal, the protection and certification requirements, and the valve drawing with interface dimensions [S2]. The final selection should be checked against the full open-close cycle, including breakaway torque, travel time, seating behavior, and loss-of-power position.
For water-service projects, use the actuator supplier’s model-selection tool as an independent sizing check. SMC provides an electric-actuator model-selection service that accepts project requirements for registered users [S3]. The tool does not replace review of the desalination valve’s torque or thrust data.
For valve-specific procurement, electric ball valve selection for water treatment provides a related check on actuator and valve interface requirements. After selection, request a submittal showing output rating, ingress protection, hazardous-area approval where applicable, materials, motor data, controls, fail-safe action, mounting dimensions, and test or inspection records [S1][S4].