Under ATEX 2014/34/EU, Zone 1 (gas) requires Category 2 equipment and Zone 2 (gas) accepts Category 3, a one-to-one link that determines which Ex protection concept is legal on a given skid [S5].
Under OSHA 1910.307, a US Class I installation may use either the Division system (Div 1 / Div 2) or the Zone system (Zone 0 / Zone 1 / Zone 2), and the document lists all five Class I designations in 1910.307(a)(2)(i)(A)–(E) [S1]. Class I, Zone 0 permits only intrinsically safe equipment, and intrinsic safety is also approved for Zone 0 and Zone 1 under 1910.307(g)(3)(iv) [S1].
Zone Definitions: Frequency and Duration of Explosive Atmosphere
Zone 0/20 is the highest-risk tier: an explosive gas or dust atmosphere is present continuously or for long periods, e.g. inside a process vessel [S5]. Zone 1/21 applies where the atmosphere is likely to occur in normal operation, typically around pumps, valves, flanged connections, and sample points [S5][S6]. Zone 2/22 applies where the atmosphere is not likely in normal operation, or persists only briefly, e.g. the annulus around a Zone 1 boundary where a leak or spill could occasionally reach [S5][S2].
OSHA maps the same logic onto US wiring: Class I, Zone 0 is a place where ignitable concentrations are present continuously or for long periods; Zone 1 is where they are likely under normal operation; Zone 2 is where they are not likely, or only for short periods [S1]. The Canadian CEC uses the same zone language, and CSA publishes the corresponding definitions for North American certification work [S2].
Equipment Categories and EPL: From Zone to Allowed Marking
ATEX equipment categories run 1, 2, 3 with descending required safety level; the EU directive 2014/34 (ATEX 114) is the legal source for that mapping [S5]. Category 1G / 1D is required for Zone 0 / Zone 20, Category 2G / 2D for Zone 1 / Zone 21, and Category 3G / 3D for Zone 2 / Zone 22 [S5]. The example the trade uses: an air-conditioner for Zone 2 gas is Category 3, while the same air-conditioner moved into Zone 1 gas must be Category 2 [S5].
IECEx uses Equipment Protection Levels (EPL): Ga for Zone 0, Gb for Zone 1, Gc for Zone 2, with the same descending safety requirement. US installations may substitute any Class I, Zone 1 or Zone 2 method per the design rules, and any Class I, Division 1 method is also accepted in the Zone 1 / Zone 2 design space [S7]. For a spec sheet, the rule of thumb is: pick the zone, then read the category or EPL off the table, then verify the Ex marking string (e.g. Ex db IIB T4 Gb) on the nameplate [S5].
Protection Techniques Allowed Per Zone

OSHA 1910.307(c)(2)(i) requires equipment to be approved for the class, the group, and the operating temperature or temperature range, so any protection technique is conditional on those three parameters [S1]. Intrinsic safety (Ex i / “i” in the marking) is permitted in Zone 0 and Zone 1, and Zone 0 is effectively restricted to it on the US side [S1]. Flameproof enclosures (Ex d) and increased safety (Ex e) are typical Zone 1 picks, while Ex nA (non-sparking), Ex nR (restricted breathing), and Ex ec are the common Zone 2 choices [S4].
Purged and pressurized (Ex p) and oil-immersed (Ex o) equipment also fit Zone 1, and encapsulation (Ex m) is allowed in both zones when the device is so rated [S4]. The North American shortcut is to read the nameplate: a Class I, Div 2 enclosure may use a purge system, an intrinsically safe circuit, or a non-incendive component design, while a Div 1 enclosure must contain any internal ignition, which is what the cast Ex d housing delivers [S4][S7]. For a detailed look at cable entry sealing on those Ex d housings, see the ex d cable gland spec guide.
Decision Matrix: Protection Method by Zone and Application
For Zone 0 gas (continuous), only Ex ia with a Ga EPL is acceptable; field devices such as tank-level probes and in-line analyzers are typical, and the energy budget is so tight that simple on/off devices dominate [S1][S5]. For Zone 1 gas (intermittent, normal operation), Ex d, Ex e, Ex p, Ex ib, or Ex mb are all valid; Ex db IIB T4 Gb is the workhorse marking for motors, junction boxes, and lighting in oil & gas [S4][S5]. For Zone 2 gas (abnormal only), Ex nA, Ex nR, Ex ec, Ex dc, or Ex mc simplify the build: an Ex ec terminal box, an Ex nA motor, or a non-incendive field wiring run will usually meet code at a lower unit cost than the Zone 1 equivalent [S4].
Compare three common picks on cost, weight, and integration effort. A cast aluminum Ex db IIB T4 Gb junction box costs less per unit and weighs roughly half of a stainless 316L equivalent, but 316L is the default for offshore and any chloride-exposed site. An Ex nA motor on Zone 2 saves on cabling versus Ex e because no special terminals are required, but the motor nameplate still must be marked Gc and the supply short-circuit protective device coordinated to the machine's tE time. A purge system (Ex p) is flexible, accepting general-purpose enclosures inside the pressurized enclosure, but it needs a certified purge controller, a vent stack, and routine leak testing on the schedule called out by the manufacturer. Reference [S4] is consistent with this trade-off: Ex d is the workhorse for Zone 1, intrinsic safety is reserved for instrumentation, and Zone 2 unlocks cheaper non-incendive or restricted-breathing designs.
Selection Criteria Beyond the Zone

Group rating is non-negotiable. The four NEC gas groups A (acetylene), B (hydrogen), C (ethylene), and D (propane, methane, gasoline) map onto ATEX gas groups IIC (most onerous, includes H2), IIB, and IIA, and any equipment approved for IIB is also approved for IIA but not for IIC [S3][S4]. A Group B / IIC site such as a hydrogen compressor skid eliminates roughly half of the off-the-shelf Zone 1 catalog and pushes the spec toward stainless or bronze, not aluminum.
Temperature class is the second hard filter. The T1–T6 surface temperature scale (450 °C down to 85 °C max surface) is shared between NEC and ATEX, and the gas auto-ignition temperature sets the floor: a hydrogen-rich stream forces T6 selection in most practical cases. Ambient range, IP/NEMA rating, and corrosion category are layered on top: an IP66 enclosure rating is now standard on most Zone 1 cast housings, while NEMA 4X is the equivalent North American shorthand for stainless washdown sites. Reference [S4] warns that equipment must be approved for the specific gas, vapor, dust, or fiber present, not just the class, so a unit approved for propane cannot be dropped onto an ethylene service without re-checking the group letter [S1].
Limits, Failure Modes and Common Mis-Specs
The most common error is mixing Class I, Division 1 and ATEX Zone 1 in the same procurement line. Div 1 equipment is not automatically Zone 1; the two systems are parallel, and a spec that says “Class I, Div 1 or ATEX Zone 1” needs an “or equivalent” clause plus a check on the EPL and the ATEX category [S4][S7]. A second error is picking the protection concept before the zone: a flameproof Ex d enclosure is overkill (and heavier, costlier) on a Zone 2 instrument loop where a non-incendive Ex nA field device, a Zener barrier, or an intrinsic-safety barrier would do.
A third error is ignoring the dust side. ATEX and IECEx use 20/21/22 for dust, and the protection letters shift to ta/tb/tc on the marking; the zone-to-category logic mirrors gas, but the test dusts, surface-temperature limits, and IP6x dust-ingress requirements are different [S5]. Finally, a Zone 2 enclosure does not automatically cover Zone 1; if a process change tightens the area classification, every piece of equipment must be re-evaluated against the new zone, not just the new gas group [S1][S4].
Standards and Documentation Trail

For European projects, the equipment-level rules are ATEX 2014/34/EU (ATEX 114), with the worker-side ATEX 1999/92/EC (ATEX 137) governing the area classification itself. For IECEx member countries, IEC 60079-0 and the IEC 60079-1 / -7 / -11 / -13 / -15 / -18 / -31 sub-parts give the test methods and construction requirements for each protection type. In the US, the NEC (NFPA 70) Articles 500–506 and OSHA 1910.307 are the legal layer, with UL 1203 covering explosion-proof enclosure testing for Div 1, and ISA 12.12.01 covering non-incendive equipment for Div 2 [S1][S4].
The documentation chain is the same on both sides of the Atlantic: area classification drawing → equipment list with zone, group, and temperature class → Ex certificate per equipment line → installation that follows the certificate's “X” or “U” conditions. 1910.307(b) requires that all areas designated as hazardous (classified) under the Class and Zone system be documented and that the documents be available to designers, installers, inspectors, and operators [S1]. A spec that does not name the zone, the equipment category or EPL, the group, the temperature class, and the IP/NEMA rating is incomplete and will be returned by the inspector or the EPC's hazardous-area lead.
Track for the next planning cycle: confirm whether any new build in the next 12 months sits in a Zone 1 boundary that can be downgraded to Zone 2 through vent stacks, distance, or purge, since each re-classification shifts the protection concept from Ex d / Ex e to Ex nA / Ex nR and changes the unit-cost line on the Ex motor and lighting packages. Re-validate the Ex certificates on any equipment that was moved, re-badged, or re-purposed; the zone, group, and temperature class on the nameplate, not on the packing list, is what the inspector reads [S1][S4].