Knockout Drum

A knockout drum is a pressure vessel that removes free liquid and entrained droplets from a gas stream before the gas goes somewhere liquid must not go: into a flare stack where liquid rain is a hazard, into a compressor suction where liquid slugs destroy rotors, or into a fuel gas or burner system where liquid fouls nozzles and extinguishes flames. Gas slows down in the larger vessel cross section, gravity and inertia separate droplets, inlet devices absorb momentum, and a mist eliminator catches the fine fraction the gravity section cannot, while the separated liquid collects in a bottom sump for level controlled disposal. Sizing follows droplet cutoff practice, commonly removing essentially all droplets larger than 300 to 600 micrometers in the gravity section with the mesh or vane pack polishing below that, with API 521 governing flare drum liquid handling philosophy and ASME Section VIII governing the vessel itself.

Procurement engineers meet these drums at the flare header knockout upstream of every flare stack, at compressor suction scrubbers, on fuel gas conditioning skids, at wellheads and gas gathering, upstream of dehydration and treating units, and on vapor recovery. The decision this page settles is which orientation and internals match the duty: a vertical drum for compact plots and moderate liquid loads, a horizontal drum for large liquid slugs and long liquid residence, and the inlet device, mist eliminator, holdup, and level control scope that make it a separator instead of a pot. The answer lands as an RFQ line set, gas flow and molecular weight, liquid load and slug volume, droplet cutoff, orientation, internals, and code basis, and every chapter below feeds that line set so the drum is bought against the vapor and liquid it must actually separate.

Steel cylindrical pressure vessel tank on a frame with manway and piping connections, the pressure vessel hardware class into which horizontal and vertical knockout drums are purchased for flare, compressor suction, and fuel gas liquid removal

Photo: Sludge G, CC BY-SA 2.0, via Wikimedia Commons

This page treats the knockout drum as a purchasing object: how droplet cutoff and gravity sizing set the diameter, how holdup and slug volume set the length, what inlet devices and mist eliminators add, how flare duty under API 521 differs from compressor suction duty, and how the whole decision folds into a defensible RFQ with code and level control scope included. It is written for engineers who issue separator purchase specifications, not for readers who want a brochure summary.

Chapter 1 / 06

What a Knockout Drum Is and What Is Being Decided

The defining act of the machine is phase separation by gravity with hardware assistance. A gas stream carrying liquid, as film on walls, as mist, or as slugs, enters the drum, the area increase drops the gas velocity by a large factor, droplets with enough terminal velocity relative to the gas fall or settle against the flow, and the collected liquid pools below the gas path. Inlet devices, diverter plates, half pipe inlets, cyclonic entry vanes, absorb the momentum of the incoming jet so it does not shear the pool into new droplets, and demisting hardware at the outlet, wire mesh pads or vane packs, coalesces the fine mist that survives the gravity section. What leaves the drum is gas dry enough for the downstream machine, and what stays is liquid waiting for a level control valve to dispose of it.

What is being decided in this purchase is four commitments at once. First an orientation: vertical drums suit compact plots, low to moderate liquid loads, and duties where footprint rules, horizontal drums suit large liquid volumes, slug catching, and long liquid residence with easier level interface control. Second a sizing basis: gas capacity at the worst credible flow, droplet cutoff, and the liquid handling, holdup volume between level trips and residence time for degassing. Third the internals: inlet device type, mist eliminator type and thickness, baffles and vortex breakers, and heating or insulation where the liquid can wax or hydrate. Fourth the control and safety envelope: level instrumentation and dump philosophy, relief protection, and the code basis, ASME Section VIII for the shell, API 521 for flare duty liquid philosophy. A buyer who leaves any of the four to vendor default gets a pot, not a separator.

Against its neighbors the knockout drum occupies precise ground in the separation house. A steam separator removes condensate from steam lines, a dedicated two phase duty with its own page. A mist eliminator is a component, the demister inside this drum and other vessels, and its page details the media. An oil water separator divides a liquid liquid stream, gravity or coalescing, a different job. A flash tank is a thermodynamic vessel that makes vapor from pressure drop, usually on condensate, with no gas feed stream at all. A three phase separator or slug catcher, upstream oil and gas neighbors this page deliberately does not double, handles gas oil water split and pipeline slugs on a bigger stage. The knockout drum is the two phase guard vessel at the gas user, and this page is its authority. Naming the neighbors keeps vendors quoting the same machine.

Standards frame the datasheet. The vessel itself is ASME Section VIII Division 1 territory with its materials, weld, and test regime, stamped and documented. Flare duty draws on API Standard 521, the pressure relieving and depressurizing systems standard, which sets flare knockout liquid handling philosophy, including the expectation that flare drums manage credible liquid loads, rain, condensation, and carryover from relief, with disposal pumps or drains sized so liquid cannot reach the stack tip. Compressor suction duty draws on the compressor vendor's gas quality requirements and machinery standards like API 617 and 618 context for scrubbing. Demisting internals follow vendor performance practice, with droplet removal and pressure drop stated against actual gas properties. A datasheet that quotes a diameter with no droplet cutoff basis and no code line is a price tag, not a specification.

The station around the drum deserves naming in the RFQ too. Level control is the heart of it: a level transmitter, magnetic level gauge for local indication, and a dump valve, with level switches or transmitter alarms at the trip points that protect the flare, compressor, or burner. A sight glass at platform height is cheap commissioning evidence. Pressure transmitter and temperature transmitter readings support the relief and process record, and a safety relief valve or the connection into the plant relief system protects the blocked out case. On flare duty, the liquid disposal may add a pump, and on cold service the drum adds heat tracing and insulation against wax or hydrate. Nozzles for drains, vents, and the mist eliminator access belong on the drawing from the start, because retrofitting manways into a coded vessel is not a change order, it is a new vessel.

Chapter 2 / 06

How Gravity and Droplet Cutoff Size the Vessel

Gas capacity sizing rests on a single idea: a droplet of a chosen cutoff size must settle against the upward or cross flow of gas. The classical working tool is the Souders Brown relation, which caps the allowable gas mass velocity through the drum net area as a function of gas and liquid densities, with an empirical factor k adjusted for duty and for how much polishing the demister does. Design practice sizes the gravity section to drop essentially all droplets above roughly 300 to 600 micrometers, larger droplets on plain flare drums, finer with good inlet distribution, and lets the wire mesh or vane pack catch most of what remains down to the few micron level. The cutoff number belongs in the RFQ, because it is the difference between a drum that protects a compressor and a pot with a flange.

Orientation changes where the settling happens. In a vertical drum, gas rises and droplets fall against the flow, so the cross sectional area above the liquid setpoint does the gravity work, and the height above and below the normal liquid level provides disengagement space and liquid holdup. In a horizontal drum, gas travels along the vessel and droplets fall across the flow path, so the vapor space height above the liquid and the drum length do the work together, and a horizontal drum at the same diameter buys much more separation length per unit of plot width. Horizontal drums also settle the liquid more gently, which matters when the liquid must degas or when interface control is needed, and they take large slugs without the liquid reaching the gas outlet, which is why flare headers and slug prone service go horizontal.

Liquid sizing is where flare and suction duties differ most. The drum must hold the liquid that arrives between disposal actions, and the level band between the low trip and the high trip must contain the credible slug, on flare duty the liquid the relief event or rain and condensation produce per API 521 logic, on suction duty the line volume the upstream piping can drain in one upset. Residence time in the band, minutes on most duties, longer where degassing or sand settling matters, sets the volume, and the dump system capacity must exceed the steady liquid arrival rate with margin so the band does not fill during one cycle. The buyer states the liquid load honestly, slug volume and rate, because every separator horror story starts with a liquid load the datasheet rounded down.

Inlet momentum is the enemy the internals answer. A gas jet entering at header velocity will re entrain everything it meets, so inlet devices exist to spend that momentum harmlessly: a simple diverter plate for small drums, half pipe and tangential inlets that spread the jet, and cyclonic or vane inlet devices that spin out the coarse droplets before the gas reaches the gravity section. Downstream of the gravity section, the demister polishes: wire mesh pads, layers of knitted wire that coalesce mist by impaction, cheap and effective to about 99 percent removal above roughly 5 micrometers at low pressure drop, a few hundred pascals to a thousand or two, and vane packs, profiled plates that turn the flow and fling droplets to walls, which tolerate higher velocities and fouling and liquid loads. High performance axial flow cyclone bundles sit between and above, for gas rates that would blow liquid through mesh. The choice follows gas density, fouling tendency, and the downstream machine's tolerance, and chapter 3 maps it.

The sizing arithmetic closes with pressure and property honesty. Gas density rises with pressure, droplet settling gets harder, and demister performance changes: mesh pads that work at atmospheric flare conditions reach their re entrainment limit in dense gas, pushing the design to vanes or cyclones. Molecular weight moves the same direction, so the RFQ states the gas analysis or at least molecular weight range, flow at the worst credible condition, and the coincident temperature. The vendor sizing deliverable should show the droplet cutoff calculation, the velocity check at maximum flow, the demister velocity window, and the holdup and residence check against the stated liquid load, because those four pages of arithmetic are the machine.

Chapter 3 / 06

Drum Types, Internals, and Duty Boundaries

The vertical knockout drum is the compact answer: a cylindrical vessel with side or bottom inlet, gas outlet at the top, liquid sump at the bottom, and the mist eliminator near the outlet. Vertical drums suit compressor suction scrubbing at moderate liquid loads, fuel gas conditioning, and any plot where the vertical space is cheaper than the footprint. Their limits are liquid capacity, the level band lives on the vessel cross section, and sensitivity to slugs, a large slug walks the level straight toward the gas outlet. Vertical drums with cyclonic inlet devices, the vertical two barrel separators used on gas plants, push gas capacity up by doing the coarse separation in swirl and the polishing in mesh, at the price of internals complexity.

The horizontal knockout drum is the liquid machine: inlet at one end, usually with a device or baffle, gas traveling the long dimension above a liquid inventory, demister in the outlet region, and a boot or sump where heavy liquid or water collects. Horizontal drums hold slugs that would flood a vertical drum, give calm liquid for degassing and interface control, and put the mist eliminator far from the liquid surface. They cost in footprint and in slightly more complex level instrumentation across the long axis, and they are the default on flare knockout duty, slug prone gathering, and any service where the liquid load is a process reality rather than a nuisance. Sizing discipline for horizontals includes checking liquid transport along the drum, the liquid must actually reach the outlet nozzle at the arrival rate, an error that shows up as a drum half full at the inlet end.

Duty flavorings write themselves onto the two geometries. The flare knockout drum, horizontal at or below grade near the stack, sized per API 521 liquid philosophy, often with a disposal pump and heater in cold service, and with rain and condensation in the liquid inventory on purpose. The compressor suction scrubber, vertical usually, sized on the compressor vendor's liquid tolerance, with high reliability level instrumentation because a trip is cheaper than a rotor. The fuel gas filter separator, two compartment machines that combine a coalescing filter section with a mist section, leaning toward the filter separator architecture where solids and aerosols both matter to the burner or gas engine, with its own page neighbors in the coalescing filter family. The vapor recovery or vent knock out pot, small, simple, often vented to atmosphere through a flame arrester where the mixture warrants.

Boundaries are worth stating bluntly. This is a two phase vessel: a stream needing gas oil water split belongs to three phase separator design, and pipeline slug handling at scale belongs to the slug catcher family, both deliberately out of this page's scope as unused neighbors. It is not a scrubber tower: acid gas removal and absorption are columns with packing or trays, chemical duty, not guard vessels. It is not a flash tank, which makes vapor rather than removing it, and it is not a demister vessel alone, since the mist eliminator is a component this page buys. The type map below compresses the boundaries into one table.

Drum typeBest dutyLiquid handlingWatch out for
Vertical, plain or diverter inletCompact plots, low liquid loadSump sized between level band limitsSlug service floods the level toward the outlet
Vertical with cyclonic inlet deviceHigher gas capacity, gas plant serviceSwirl separates coarse load earlyInternals fouling on dirty or scaling service
Horizontal, inlet device plus demisterFlare KO, slugs, large liquid loadsLong inventory, slug capture, degassingFootprint, liquid transport along the drum
Horizontal with bootHeavy phase or water bearing gasBoot for water, main for hydrocarbonInterface control complexity
Fuel gas filter separatorBurner and engine fuel conditioningFilter and mist sections combinedFilter element change discipline
Vent pot with arresterSmall atmospheric vent streamsManual or small dumpMixture hazard analysis owns the arrester scope
Chapter 4 / 06

Key Specification Parameters

The table below decodes the datasheet lines that decide whether a quoted drum separates what the process sends it. Each row is a purchase defining parameter; the paragraphs after the table explain what to demand and what a weak answer looks like.

AttributeTypical range or optionsWhat it decides
Gas flow and molecular weightDesign and maximum with gas analysisDiameter, velocity check, demister window at worst density
Operating pressure and temperatureWith coincident and relief basisVessel wall, density, and materials envelope
Droplet cutoff300 to 600 micrometers gravity, finer with demisterThe separation guarantee and downstream protection
Liquid load and slug volumeSteady rate plus credible slugLevel band, holdup, residence, and dump sizing
OrientationVertical or horizontal by plot and liquid dutyGeometry of separation and the instrumentation layout
Inlet deviceDiverter, half pipe, vane, cyclonicMomentum absorption and coarse separation
Mist eliminatorMesh pad, vane pack, cyclone bundlePolishing to outlet droplet spec and pressure drop
Residence and degassingMinutes in band, longer on heavy liquidLiquid quality to disposal and foaming control
Vessel code basisASME VIII Div 1 with relief philosophyLegal envelope, nozzle and manway scope, test regime
Level control scopeTransmitter, switches, dump valve, pumpThe trip points that protect flare, compressor, or burner

The droplet cutoff and demister rows carry the warranty. Demand the sizing calculation with the cutoff basis stated, the gravity section velocity at maximum flow, and the demister velocity window check, mesh pads flood and re entrain above their window just as they underperform below it, and vane packs have their own limits. For compressor suction duty, ask the compressor vendor for the liquid tolerance in liters per hour or droplet size and check the drum selection against it, because a drum sized by habit rather than by the machine downstream is how rotors meet liquids. A quotation that quotes a diameter with no calculation is selling steel, not separation.

The liquid rows deserve the same honesty. State the steady liquid rate and the credible slug, and demand the holdup and residence check against them, with the level band shown between the low level trip, normal setpoint, and high level trip, and the dump capacity verified above the arrival rate. On flare duty, state the rain and condensation allowance and the disposal philosophy, pump or drain, with its capacity basis, because API 521 expects the flare drum to manage the credible liquid load without sending it up the stack. The second table compresses the duty decisions the way a specification meeting argues them.

DutyConfiguration to specifyCheck before order
Flare header knockoutHorizontal at grade, generous liquid inventory, disposal pump or drainAPI 521 liquid load basis, rain allowance, cold service heating
Compressor suction scrubberVertical with inlet device and high reliability level loopCompressor vendor liquid tolerance and trip philosophy
Fuel gas to burners or enginesFilter separator or drum with coalescing sectionAerosol and solids tolerance of the downstream nozzles
Gathering or slug prone lineHorizontal sized for line volume slugSlug volume honesty, liquid transport along the drum
Cold or waxing serviceHeated and insulated drum with traced nozzlesHeat tracing scope and winterization of the dump path
Vent stream with flammable mixtureVent pot with flame arrester scopeHazard analysis owns arrester sizing and placement
Chapter 5 / 06

Selection Decision Factors and RFQ Language

The decision sequence is short enough to run as a specification meeting checklist, and each step eliminates a class of quotations before price comparisons begin.

  1. State the gas honestly: analysis or molecular weight, design and maximum credible flow, coincident pressure and temperature, because density writes the whole sizing.
  2. State the liquid honestly: steady rate, composition, and the credible slug volume, with rain and condensation on flare duty, and the downstream tolerance the separation protects.
  3. Choose orientation: vertical for compact plots and moderate liquids, horizontal for slugs, large inventories, and flare duty.
  4. Set the separation basis: gravity droplet cutoff, demister type and its velocity window, and the outlet droplet or liquid carryover number the downstream machine accepts.
  5. Set the liquid basis: level band, holdup, residence, dump capacity above arrival rate, degassing or interface needs, and heating where the liquid can wax or hydrate.
  6. Fix the vessel envelope: ASME VIII design conditions with the upset and relief case, materials by chemistry and temperature, manway and nozzle scope for internals access.
  7. Fix the control and safety scope: level transmitter and switches or transmitter alarms at trip points, dump valve or pump with failure action, relief path, and instrumentation list.
  8. Fix the verification evidence: sizing calculation deliverable, vessel code documentation, demister performance basis, and the acceptance logic on level trip tests.

Against neighboring equipment the comparison a specifier needs runs as follows, and it belongs here in the selection chapter rather than in the page title. A steam separator and a mist eliminator are the component level relatives, the demister inside this drum and the condensate guard on steam service. An oil water separator splits a liquid liquid stream. A flash tank makes vapor from condensate pressure drop and is not a gas feed vessel. Three phase separators and slug catchers handle the gas oil water and pipeline slug duty upstream and are deliberately not doubled by this page. A coalescing filter does aerosol polishing on clean gas where a filter separator architecture fits. The knockout drum is the two phase guard at the gas user, and the RFQ that names it so keeps every vendor on the same machine.

The RFQ block should be written once and reused. A complete block reads: gas analysis or molecular weight with design and maximum flow at coincident pressure and temperature; liquid rate, composition, and credible slug volume with rain and condensation on flare duty; required outlet quality stated as droplet size or liquid carryover tolerance of the protected machine; orientation named with the plot basis; gravity section cutoff basis and demister type with velocity window check; inlet device type; level band with holdup and residence check against the liquid load; dump system capacity and philosophy with failure action; vessel design conditions to ASME VIII with materials and the relief case; heating, tracing, and insulation scope for cold or waxing service; nozzle and manway scope for internals; instrumentation list including level transmitter, switches or alarm points, pressure transmitter, temperature transmitter, and sight glass; and the calculation deliverables with code documentation. A quotation returned without the sizing calculation or the liquid handling basis is incomplete at any price.

Chapter 6 / 06

Installation, Standards, Failure Modes, and Maintenance

Installation quality decides whether the calculated separation exists in steel. Piping enters the drum the way the sizing assumed: the inlet device only works if the jet arrives where the drawing put it, and a feed line modified in the field to dodge a cable tray has cost more separator capacity than any internals upgrade can return. Level instruments are set at their design elevations with the band verified against the process data sheet, the dump valve installed with its failure action checked, and the flare or vent path proved open before first feed. Support and expansion follow vessel practice, and on cold service the heat tracing is commissioned and its thermostats set before the first winter teaches the lesson instead.

Commissioning proves the liquid story and the trips. Fill to the normal level and verify the level transmitter against the magnetic level gauge and the sight glass, then run the trip tests: high level trip that alarms or diverts, low level that protects the dump from gas blowthrough, and the dump valve stroke at real differential. Challenge the drum with a realistic liquid batch, at commissioning every operator learns what a slug arriving looks like on the level trend, and the calibration of level alarms against real events is worth more than any datasheet. Record the baseline pressure drop across the drum and demister, and the gas rate versus level behavior at several flows, because those baselines are the reference for every campaign that follows.

Failure modes in service follow a short and predictable list. Liquid carryover heads the list and traces to a liquid load the drum was never told about, a dump system that cannot keep up, a failed or mis set level loop, or a demister past its window or flooded, and it announces itself downstream, flare rain, compressor vibration, or burner fouling, before anyone looks at the drum. Demister fouling and carryover rise together as the mesh or vanes plug with scale, wax, or produced solids, raising pressure drop until the gas finds liquid with it, and the remedy is wash or replacement scheduled on the pressure drop trend. Level instrument drift moves the effective band until a trip that was a protection becomes a surprise, and dump valve wear, seat erosion on dirty service, turns the steady disposal into a slow leak of gas to the drain system. Corrosion at the liquid line and under insulation attacks the shell on wet sour or chloride service, and the inspection plan, thickness surveys at the corrosion circuits, is the defense the code expects.

Maintenance intervals scale with the liquid and gas chemistry more than with time. Clean dry service runs instrument calibration and the external inspection calendar with internals inspected at major turns. Dirty, scaling, or waxing service adds demister wash or exchange, dump valve overhaul, and the tracing survey to every campaign, and holds spare mesh or vane elements on site. The level loop gets exercised at every opportunity, trips proven, transmitter verified against the local gauge, because the whole vessel exists to make two or three level decisions correctly. Every campaign produces numbers, pressure drop trend, level event log, and inspection findings, and those numbers calibrate the next RFQ, which is how a purchasing file gets smarter instead of just older.

FAQ

Should my knockout drum be vertical or horizontal?

Go vertical for compact plots and moderate liquid loads, compressor suction scrubbing and fuel gas duty, where the cross section does the gravity work and the sump holds the band. Go horizontal when liquids lead the duty, flare knockout per API 521, slug prone gathering, long residence or degassing, because the long inventory swallows slugs a vertical drum would pass to the outlet. Footprint versus liquid capacity is the actual decision axis.

What droplet size should I size for?

Gravity sections commonly target removal of essentially all droplets above roughly 300 to 600 micrometers, with a wire mesh or vane demister polishing the mist below that, mesh to about 99 percent above roughly 5 micrometers. The right cutoff is set by the downstream tolerance: a flare stack tolerates more than a gas engine nozzle or a compressor rotor, so state the protected machine and let the sizing calculation show the cutoff it delivers.

How is a flare knockout drum different from a normal KO drum?

Duty philosophy. API 521 expects the flare drum to manage the credible liquid load, relief condensation, carryover, and even rain on the header, without liquid reaching the stack tip, so the liquid inventory, disposal pump or drain capacity, and often heating for cold service are designed inputs, not afterthoughts. A process guard drum protects one machine downstream, a flare drum protects a safety system.

How do I size the liquid holdup and level band?

From the liquid story you tell the vendor: steady arrival rate, credible slug volume, and the disposal rate. The band between low and high level trips must contain the slug, residence in the band must meet degassing or settling needs, and the dump capacity must exceed the arrival rate with margin so the band does not fill in one cycle. Every drum that has carried liquid over has a datasheet that rounded one of those numbers down.

Mesh pad, vane pack, or cyclone bundle?

Mesh pads are cheap and effective at moderate velocity and clean gas, flooding and re entraining above their window. Vane packs tolerate higher velocity, dense gas, and fouling, at higher pressure drop and price. Cyclone bundles serve high gas rates and liquid loads that would blow through the other two. The choice follows the velocity window check at maximum flow and worst density, which the sizing deliverable must show.

What level control does a knockout drum need?

A level transmitter with alarms at the trip points, a magnetic level gauge and sight glass for local truth, and a dump valve or pump sized above the arrival rate with its failure action chosen for the protected machine. On compressor service the loop reliability approaches a safety function, so redundant or high integrity level measurement is usual. The vessel exists to make these few level decisions correctly, so the instrumentation is not the place to economize.

What deliverables make a separator quotation defensible?

The sizing calculation showing gravity cutoff and velocity check at maximum flow, the demister window check, holdup and residence against the stated liquid load, the level band drawing, the ASME VIII design basis with the relief case, demister performance data, and the trip test logic for acceptance. A diameter quoted without that arithmetic is steel, not separation, and the difference surfaces at the first real slug.

Sources

  1. Flaretech, Flare Knockout Drums
  2. GBA, Knock-Out Drums
  3. John Zink, Flare Systems
Ask SpecForge AI