Vibrating Screen

A vibrating screen is a driven sizing machine whose screening surface, one deck or several stacked, wire cloth, woven wire, polyurethane or rubber panels, perforated plate, is stretched on a frame and vibrated by eccentric or exciters drive so that feed material stratifies, fines pass the apertures, and coarse travels to discharge. Circular motion, linear reciprocating, and multi slope banana geometries divide the family, and the machine serves scalping ahead of crushers, classifying in closed circuits, and dewatering of washed products across aggregates, mining, and industrial minerals plants. Metso's banana screen lines and Derrick's fine screening machines are representative industrial catalogs, and this page treats the screen and its feed arrangement as the purchasing object.

This page is written for the plant engineer specifying vibrating screens for a crushing and screening circuit, a minerals classification loop, or a washed product dewatering station. It works through what the machine does and what is being bought, how motion and stratification do the work, which geometries and media fit which duties, the parameters that appear on vendor data sheets, and the selection factors and RFQ language that decide whether the installed screen holds its capacity and cut through its media life.

Bulk material handling hardware of the class that feeds and receives vibrating screen circuits, shown as an installed belt conveyor

Photo: RICHI Manufacture, CC BY 4.0, via Wikimedia Commons

The decision concentrates in five places: the duty sentence, scalp, classify, or dewater, with its cut size and efficiency target; the motion geometry that matches it; the deck area and slope that carry the feed rate without blinding; the media, wire, panel, or cloth, that survives the material and holds the aperture; and the feed arrangement that presents material evenly across the deck width. Get those right and the drive, frame, and screening area follow.

Chapter 1 / 06

What a Vibrating Screen Is and What Is Being Decided

The machine this page describes is a screen box, a fabricated frame carrying one to four decks, mounted on steel coil springs or rubber mounts to isolate structure from vibration, and driven by a vibrator: a single eccentric shaft for circular motion, dual counter rotating motors or a gearbox exciter for linear motion, and the same exciters angled for the elliptical and multi slope variants. Feed lands in a feed box that slows and spreads it, material travels down the inclined or horizontal deck, stratifies so fines reach the apertures, and leaves either through the apertures to a lower deck or underpan, or over the discharge end as oversize. Motorized vibrating motors bolt directly on smaller machines; larger screens carry a cardan shaft driven exciter or twin vibrators.

What is being decided when a vibrating screen is purchased is a cut and a capacity with an efficiency number attached. The buyer is purchasing a stated feed rate of a stated material at a stated moisture to be split at a stated aperture with stated efficiency, undersize recovery in the undersize stream or oversize contamination limits, at a media wear cost per tonne that holds the operating budget. Everything on the vendor data sheet, deck dimensions, area, speed and stroke, motor power, deck angle, media, exists to support those guarantees, and the honest vendor sizes from the material's bulk properties and a screening test rather than from an area table alone.

The vibrating screen sits in the screening family with defined neighbors. It is not a bar screen, the wastewater coarse rake that intercepts rags and solids at a treatment headworks; that machine screens channel flow, not dry or washed bulk solids, and the mineral screen on this page never appears in a sewage plant. It is not a trommel, the rotating cylindrical drum that screens by tumbling at low frequency, a gentler, lower capacity geometry. It is not a static grizzly, the fixed bars that scalp oversize rock ahead of a crusher feed, though scalping duty is shared. And it is not the wrap-around sizer class of fine wet machines without discussing Derrick Stack Sizer style technology, which sits at the fine end of the same family.

Different buyers buy the same machine for different products. An aggregates producer buys multi slope banana screens to size product stages at 300 tonnes per hour per machine and scalping grizzlies ahead of the primary. A copper concentrator buys linear motion screens on crusher discharge and fine screens in the grinding circuit classification. An iron ore plant buys dewatering screens to take washed fines from slurry to conveyable cake. A sand plant buys attrition plus dewatering screens in the wash line. A recycling yard buys heavy duty scalpers for demolition feed. The specification language differs, but the stratification physics is shared.

The economics deserve their own paragraph because the screen is cheap to buy and expensive to misapply. Purchase price is modest against the crushers and mills around it, but a screen that bottlenecks the circuit caps the whole plant, a screen with the wrong media blinds every shift, and a screen with poor feed distribution wears its panels unevenly and lets coarse escape. Media consumption, panels or wire per tonne, and the labor of changes are the recurring costs. The honest comparison prices circuit availability, tons per hour at the cut, and media life together, and the cheapest deck area on the bid is usually the most expensive bottleneck in the plant.

A short tour of named duties makes the machine concrete. In a granite quarry, primary crushed rock feeds a scalping screen whose undersize bypasses the secondary cone crusher and whose oversize returns for reduction. In a gold plant, the ball mill discharge screen returns oversize to the mill while slurry flows to leach. In a frac sand plant, wash water and sand report to a dewatering screen whose underpan returns water and whose cake discharges at 15 to 20 percent moisture to the conveyor. In an aggregates wash, a three deck screen makes four products from one feed. Each duty names the same knobs, motion, area, aperture, media, and feed spread, with numbers that scale while the vibrating box barely changes.

Chapter 2 / 06

How the Motion and the Deck Do the Work

Stratification is the purpose of the motion. As the deck throws material upward and forward, particles separate by size and density, fine and heavy migrating down to the screening surface while coarse rides the top, and only stratified fines can find apertures. The throw intensity, expressed as stroke times circular frequency squared, the g factor, sets how violently the bed travels: too little and the bed stratifies slowly and blinds, too much and particles bounce over apertures and the frame and bearings pay. Typical vibrating screens run 3 to 5 g with strokes of a few to a dozen millimeters at 700 to 1500 vibrations per minute, the exact point a duty and material decision.

Motion geometry sets travel and layering behavior. Circular motion, from a single eccentric shaft, throws material in a circle on an inclined deck, is self cleaning at moderate throw, and tolerates feed fluctuation; classic inclined screens scalp and size coarse aggregates on it. Linear motion, twin counter rotating vibrators producing a straight line throw, conveys material at a controlled velocity on horizontal or slightly declined decks, builds a thin stratified bed, and dominates fine sizing and dewatering where transport control matters. Multi slope banana decks, steep at the feed end where the bed is deep and shallow at discharge, keep velocity high where the load is heavy and let the thin bed finish near aperture, doubling capacity per area over single slope at the same cut.

Aperture and media make the cut, and their honesty is the machine's honesty. Woven wire cloth offers the most open area for a given aperture and the cheapest first cost, at the price of wear life and pegging; welded and self cleaning wire variants reduce pegging of slotted apertures; polyurethane and rubber panels wear longest, damp noise, resist blinding in wet duty, and hold apertures true, at lower open area and higher cost; perforated plate serves abrasive coarse duty where flatness and life dominate. Aperture tolerance and wear growth, the tendency of woven apertures to enlarge with wear, shift the cut over a panel's life, which is why cut critical duty prefers molded apertures.

Screening efficiency has a precise meaning the RFQ should use: the percent of feed undersize that actually reports to the undersize stream. A screen passing 90 percent of its undersize is not doing the same job as one passing 98 percent, and the difference is where closed circuits gain or lose circulating load. Efficiency rises with deck length, thin beds, dry free flowing material, and matched motion; it falls with moisture near the material's surface wetness, near size particles that peg, and thick or unevenly distributed beds. Vendors quote efficiency curves from test data, and the cut size quoted should carry its efficiency context or it is a number without a meaning.

Wet duty adds the water mechanics. Spray water on the feed and along the deck helps fines through apertures and washes slimes off the coarse product; dewatering screens use linear motion, uphill or level decks, and drainage media to walk water out of a bed until the mass of particles forms a cake that conveys off with residual moisture set by the material and the drain time. Underpans collect the water and fines to a sump, and the screen becomes the junction of a water circuit that needs pumps and thickening or settling downstream. Wet screening areas and media differ from dry, and the RFQ should state moisture, spray rates, and product moisture targets explicitly.

Structure and vibration management close the physics. The screen box resonates if the mount isolation is wrong, and foundations, supporting steel, or the screen's own walkways take the beating; isolation springs are selected so the machine runs above its natural frequency and transmits little to structure. Motorized vibrators and exciters carry bearings whose lubrication and temperature are the machine's vital signs, and deck clamping, tension rails for cloth and bolted or hook mount for panels, holds the media so it works the bed instead of flopping in it. A screen that rattles is a screen that is telling the plant about its clamping or bearings.

Chapter 3 / 06

Motion Types, Deck Configurations, and Duty Boundaries

Configuration choice begins with the duty sentence and the motion that fits it. Scalping coarse, rock ahead of crushers, favors heavy inclined circular motion or grizzly decks; intermediate sizing in aggregates favors multi slope banana screens for capacity per area or classic inclined decks for simplicity; fine sizing and de sliming favor horizontal linear motion and, at the finest cuts, stacked fine screening machines; dewatering favors linear motion with drainage media and modest slope. Deck count stacks cuts: a single deck splits two products, each added deck splits one stream further, and multi deck machines make several products from one feed in the aggregates house style.

ConfigurationMotionTypical dutyCharacter
Inclined single deckcircularcoarse scalpingSimple, tolerant, moderate area
Multi slope bananalinearhigh tonnage sizing2x area productivity
Horizontal linearlinearfine sizing, close cutThin bed, controlled convey
Dewatering screenlinear uphillwashed product drainCake to 15-20% moisture
Stacked fine screenerlinear, split flowfine wet classificationReplicates area vertically

Duty boundaries keep the selection honest. The vibrating screen is not a crusher, and feed with oversize beyond the deck's structural tolerance must be scalped first, by grizzly or by the crusher circuit's jaw and cone stages. It is not a classifier for fine slurry cuts below roughly 100 to 150 micrometers, where hydrocyclones and fine screening machines divide the duty, a cyclone separator loop being the grinding circuit's default. It is not a washer, though spray and dewatering duty ride on wash plant machinery upstream. And it is not the wastewater headworks machine: the bar screen family owns channel screening, a different machine for a different medium.

Where it sits in the circuit matters as much as the machine. In closed circuit with a cone crusher, the screen's oversize returns by conveyor to the crusher and its undersize is product or feeds the next stage; the screen is the circuit's valve, and its capacity sets the loop's tonnage. On mill discharge, a screen or trommel protects the downstream pump and classification. In the wash plant, dewatering screens receive cyclone underflow and discharge to stockpile conveyors. Feed and discharge conveyors, a belt conveyor under each stream, chutes with wear liners, and dust collection on dry duty, are the screen's real neighbors and belong on the layout early.

Structure, access, and noise shape the installed machine. Screens need support steel or a tower designed for the vibrating load with isolation done right, access platforms for media changes on both sides, and feed chutes designed to slow and spread material rather than hammer one spot of the deck. Noise is a regulatory number in many jurisdictions: enclosed screen houses, polyurethane media, and rubber liners bring a plant under its limit. The machine that can be relined safely and quickly, platforms, hoists, panel handling, keeps its availability, and that is an RFQ line item, not an afterthought.

The circuit around the screen supplies half its performance, so the neighbors belong in the selection paragraph. Feed arrives from the crusher or mill discharge on a belt conveyor or, on washed duty, in slurry that a slurry pump delivers to the feed box; spray water is metered and often monitored with an electromagnetic flow meter so the wet circuit's water balance holds. Downstream, the products leave on conveyors, and on fine duty a rotary dryer or stockpile conveyor receives the cut; dust on dry circuits goes to a bag filter or a suppression set. The drive itself is a candidate for a variable frequency drive where blinding behavior changes with moisture and season, letting the operator trim stroke frequency instead of changing sheaves, and a load cell or weightometer on the feed belt closes the tonnage survey. Screens are cheap machines in expensive circuits, and the RFQ that names the neighbors gets a screen matched to its circuit rather than a screen matched to a catalog.

Chapter 4 / 06

Key Specification Parameters

The data sheet parameters fall into four groups: geometry, dynamics, media, and structure. Geometry parameters are deck width and length, number of decks, and deck angle or slope profile. Dynamics parameters are vibration frequency, stroke amplitude, the resulting g factor, motor power per vibrator, and the motion path. Media parameters are media type, aperture and its tolerance, open area percent, panel or cloth fixing, and expected wear life. Structure parameters are machine mass, isolation type, feed arrangement, and allowable feed size. A quotation that omits stroke and frequency, or the g factor they produce, is not comparable to one that states them.

ParameterTypical rangeDesign note
Deck width x length0.8 x 2 to 3.6 x 8.5 mWidth limits by feed spread
Cut size range0.1 to 300 mmMedia sets the fine bound
Frequency700-1500 rpmWith stroke gives the g
Stroke3-12 mmCoarse duty likes long
G factor3-5Stratify vs structure trade
Deck slope10-25 deg, banana stagedVelocity and bed depth
Open area25-60+%Wire high, panels lower
Motor power2 x 1.5 to 2 x 22 kWPer vibrator pair
Isolationcoil springs or rubberAbove resonance mount

Capacity and efficiency deserve explicit numbers in every specification because they are the contract. The vendor should state the capacity basis, tons per hour at bulk density, at the stated feed size distribution and moisture, the aperture and cut size with the efficiency basis, and the expected blinding behavior on near size material. Screening area is then derived, not asserted: effective area discounts blind strips, clamping, and the feed's need for a spreading zone. Where the duty is close cut or wet, a screening test on the actual material returns the numbers, and vendors who quote area tables without asking for the size distribution are quoting a different material.

Media life and wear items round out the sheet. Panel or cloth wear life at the stated duty, price per square meter, and change time set the media budget; tension rails, bolts, and wear liners on chutes and feed boxes are the recurring mechanical items; vibrator bearings, with their lubrication interval and temperature monitoring provision, are the machine's critical care points. The data sheet should state the media fixing system, hook, bolt, or tension, because it sets change time and the array of spares the plant holds. A buyer who accepts media unspecified has agreed to discover the plant's main consumable at the first shutdown.

Safety and standards close the sheet. Guarding on vibrators and cardan drives, isolation lockout for media changes, and the structural design of the support steel under a vibrating load follow machinery safety practice; noise enclosure design follows the site's occupational limits; and in some jurisdictions vibrating machinery carries specific machine directive conformity. None of these are exotic, but the access platform and hoist provision for media changes is the item most often value engineered away and most often regretted at the first relining shift.

Chapter 5 / 06

Selection Decision Factors and RFQ Language

Selection starts from the material and the duty sentence. The designer writes the material and its size distribution, bulk density, moisture, and abrasiveness; the duty, scalp, size, or dewater, with the cut size or sizes and the product specs; the feed rate per machine and the circuit context, closed loop or final product; and the site context, headroom, noise limits, and climate. From that basis, motion type, deck area, and media follow with little freedom. An RFQ without the feed size distribution invites vendors to assume the friendliest curve in their catalog.

Duty driverFavored configurationWatch item
Crusher circuit scalpinginclined circular or grizzlyOversize tolerance, impact wear
High tonnage product sizingbanana multi slopeFeed spread across width
Fine close cut, dryhorizontal linearNear size blinding, dust
Washed product dewateringlinear dewatering deckDrain time vs cake moisture
Fine wet classificationstacked fine screensSpray water and underpan design

Feed arrangement is the second decision and it is made with the screen, not after it. The feed box or chute must slow the stream, often off a conveyor, spread it to 80 percent or more of deck width within the first deck length, and present it on the media without hammering one spot; a feed that hits as a point load wears a hole and passes coarse where it lands. Vendor feed box design, distributor plates, and the conveyor head chute belong in the purchase, and the layout that gives the screen a gentle, wide feed is the layout that gets the rated capacity. In multi deck machines, the top deck feed arrangement determines every cut below it.

Media selection is the third decision and it is a wear economics choice. Wire cloth buys open area and first cost; panels buy life and aperture honesty; the blend, panels in high wear zones and cloth where open area rules, is common. Wet and blinding duty pushes to polyurethane and self cleaning media; abrasive coarse duty pushes to plate and heavy wire; cut critical fine duty pushes to slotted panels held to tolerance. The vendor should propose the media with life and price per square meter, and the plant should hold the pair, media life and cut drift, as the acceptance, because a media that lasts forever while its apertures grow is not a bargain.

The RFQ language that returns comparable offers states the material and the numbers demanded. State material, feed size distribution, bulk density and moisture, feed rate per machine, duty and cut size with efficiency target, product specifications, closed or open circuit context, wet with spray rates or dry, noise limit, and the media life and change time basis expected. A complete RFQ paragraph reads: granite crushed feed 0 to 40 millimeter at 350 tonnes per hour, dry, split at 10 millimeter with minimum 95 percent undersize recovery, banana screen, polyurethane panels with 18 month expected life in abrasive duty, noise below 85 dB(A) at one meter with enclosure by vendor.

Commercial comparison is only fair on a normalized basis. Offers should be forced onto one table: effective deck area and dimensions, motion and dynamics with g factor, capacity and efficiency at the stated basis, media proposed with life and price, motor power and drive type, structural mass and isolation, access provision for media change, delivery, and the spares package. The cheapest screen is very often the smallest area at the highest stroke, and its operating cost lands in media wear and blinding downtime within the first quarter of operation.

Chapter 6 / 06

Installation, Standards, Failure Modes, and Maintenance

Installation is a structural and dynamic erection. Support steel or the screen tower builds to the vibrating load with the isolation springs landing on their pedestals; the screen sets on its mounts, level and square, with the feed chute lined and aimed to spread, and discharge chutes fitted with generous clearance for the stroke circle; vibrators and motors mount, wire, and rotate check, with the pair turning against each other for linear motion. Commissioning runs the machine empty to verify stroke, frequency, and motor current, then on feed at ramp, observing bed spread and cut, and tuning spring position, stroke angle, and feed splitter until the partition curve matches design. The commissioning survey, cut samples on each stream, is the machine's birth certificate.

Failure modes have a known hierarchy. Media failure, torn cloth, cracked panels, loosened clamping, leads the routine list and shows as coarse in undersize or a hole in the cut; blinding and pegging, near size particles locking in apertures, cut capacity and are a media and duty signature; vibrator bearing distress announces in temperature and noise and stops the machine when ignored; structural cracks in screen box side plates and cross members come from vibration fatigue and poor isolation; and spring failure changes the machine's attitude and stroke. On the process side, uneven feed wears one lane of the deck while the other passes nothing. Nearly all announce themselves in cut quality and bearing trends.

SymptomLikely causeFirst response
Coarse in undersizetorn media or clampingInspect deck, renew or retension
Capacity fallingblinding or peggingMedia change, spray, stroke review
Bearing hot, noisyvibrator distressLube, schedule bearing change
Side plate cracksfatigue, bad isolationStructural repair, springs audit
One lane wearingfeed not spreadFeed box and chute correction

Maintenance is planned around media and vibrators. Media inspection every shift by cut quality, scheduled changes by tonnage and wear survey rather than failure; vibrator lubrication on interval with temperature trending, bearing change at the manufacturer's hour limit, and exciter gear inspection where fitted; spring and mount inspection at every media change; and chute and wear liner renewal tracked as tonnage items. The relining shift's duration is the availability number, and platforms, hoists, and panel handling bought with the machine pay for themselves at every change. Spares hold a full media set, vibrator bearing kits, springs, and wear liners.

Operational stewardship is what the purchase actually bought. Operators who sample the cut each shift, who keep the feed spread and the spray water honest, and who trend bearing temperature and media wear, run screens to their rated capacity between planned changes; operators who ignore the cut quality discover media failure as coarse in the product silo and blinding as a circuit bottleneck. The trend board, cut size, undersize recovery, bearing temperature, and tons since media change, is the screen's real contract, and reading it weekly keeps the cheapest machine in the plant from becoming the most expensive one.

FAQ

What is the difference between a circular and a linear vibrating screen?

Circular motion from a single eccentric shaft throws material in a circle on an inclined deck, self cleaning and tolerant, the classic choice for coarse scalping and intermediate sizing. Linear motion from twin counter rotating vibrators produces a straight line throw that conveys a thin, stratified bed on horizontal decks with controlled velocity, which fine sizing and dewatering need. Multi slope banana screens use linear motion on staged slopes to gain capacity per area on high tonnage duties.

What is a banana screen and when should I choose one?

A banana or multi slope screen runs a deck that is steep at the feed end, where the bed is deep, and flattens toward discharge, where the bed is thin; velocity stays high early for fast stratification and slows at the end for finishing, so capacity per square meter roughly doubles over a single slope screen at the same cut. Choose it for high tonnage sizing in aggregates and minerals where footprint and structure cost matter; classic inclined decks remain simpler and cheaper at moderate tonnage.

How do I stop a vibrating screen from blinding?

Blinding, near size particles pegging in apertures, is fought by media selection and dynamics: self cleaning wire or slotted polyurethane apertures resist pegging, higher stroke and g factor flex the media and dislodge near size, spray water helps in wet duty, and anti blinding inserts exist for stubborn materials. If the material runs near its surface moisture, drying or dilution changes the game. The durable fix is matching media aperture shape to the material's near size fraction, a choice made from a screening test.

What screen media lasts longest, wire or polyurethane?

Polyurethane and rubber panels generally outlast woven wire several times over in abrasive duty, hold apertures true, damp noise, and resist wet blinding, at higher first cost and lower open area. Wire cloth offers the most open area and cheapest replacement, favoring dry, high volume, moderate wear duty. Many plants blend the two, panels in high wear lanes and cloth where open area rules. The decision is media cost per tonne, not price per square meter, and the vendor should quote expected life at your duty.

How much moisture can a dewatering screen remove?

A linear motion dewatering screen with drainage media takes washed sand and similar products from slurry or cyclone underflow to cakes commonly around 15 to 20 percent surface moisture for typical sands, finer and slimmier materials finishing wetter, coarser draining drier. The levers are drain time, deck length and velocity, bed depth, media aperture, and sometimes vacuum or uphill assist. The target moisture matters to conveyability and stockpile drainage, and belongs in the RFQ as a guarantee number.

How is screening efficiency defined and what should I specify?

Efficiency is the percent of feed undersize that actually reports to the undersize stream, sometimes paired with oversize contamination limits. A screen passing 95 percent of undersize is doing materially more work than one passing 85 percent, and in closed crusher circuits the difference shows directly in circulating load. Specify the efficiency basis with the cut size, for example minimum 95 percent undersize recovery at the 10 millimeter aperture, and demand commissioning samples to prove it.

Is a vibrating screen the same machine as a wastewater bar screen?

No. The bar screen is a channel machine at a treatment plant headworks, raking rags and coarse solids from flowing sewage, while the vibrating screen is a dry or washed bulk solids machine for aggregates and minerals circuits. The two share the word screen and essentially nothing else: different media, different motion, different materials, different plants. This page covers the vibrating bulk materials machine only.

Sources

  1. Metso, Banana screens
  2. Metso, GMF Series banana screens
  3. Metso, EF Series banana screens
  4. Derrick, Stack Sizer fine screening machine
  5. Derrick, Linear motion screens
Ask SpecForge AI