Jaw Crusher

A jaw crusher is a compressive size reduction machine that reduces hard and abrasive rock, ore, concrete, and demolition debris between a fixed jaw and a moving jaw, one of them carried on an eccentric shaft, so that the material is squeezed and split as the jaws close and dropped as they open. It is the primary crusher in the overwhelming majority of aggregates quarries, mines, and recycling plants: the machine that takes run of quarry boulders and plant demolition material and delivers a crushed stream the secondary and tertiary stages can size. Metso's Nordberg C Series and Sandvik's stationary jaw crusher lines are the reference catalogs of the class, and this page treats the crusher and its immediate plant as the purchasing object.

This page is written for the engineer specifying a primary jaw crusher for a quarry, a mine, or a recycling yard. It works through how the jaw motion and the closed side setting size the product, which crusher types and jaw profiles fit which rocks, the parameters on vendor data sheets, and the selection factors and RFQ language that decide whether the installed machine meets its capacity and product size guarantees.

Belt conveyor hardware of the feed and discharge arrangement that serves a primary crushing station

Photo: RICHI Manufacture, CC BY 4.0, via Wikimedia Commons

The decision concentrates in five places: the feed size and hardness of the rock, the product size the downstream stages demand, the closed side setting and setting adjustment the duty needs, the drive power and uncrushable protection the machine carries, and the stationary or mobile installation the site implies. Get those right and the model choice follows.

Chapter 1 / 06

What a Jaw Crusher Is and What Is Being Decided

The industrial machine this page describes is built around two crushing jaws. The fixed jaw is bolted to the front frame; the moving jaw, in the single toggle design that dominates modern plants, hangs from an eccentric shaft and closes against the fixed jaw at the bottom through the toggle plate and the pitman that links them. Manganese steel dies, corrugated or flat toothed liners, bolt to both jaws and take the wear, and the whole assembly sits in a heavy welded frame with a flywheel on the eccentric shaft, a drive motor through belts and often a gearbox or direct drive, and a discharge opening at the bottom whose gap is the machine's principal setting. Feed openings on production machines run from roughly 400 by 600 millimeters to beyond 1,600 by 2,000 on the largest quarry primaries.

What is being decided when a jaw crusher is purchased is a capacity guarantee at a product size, delivered at a wear cost per ton. The buyer is purchasing a machine that will swallow the quarry's or the yard's largest material, hold a setting under load, and turn out a crushed product whose top size the secondary stage, screen circuit, or customer specification accepts, with manganese dies that last a predictable tonnage between changes. Everything on the vendor data sheet, feed opening, maximum feed size, setting range, capacity curve, installed power, machine mass, exists to support those guarantees, and the five decisions this page works through are the ones that determine whether the installed crusher holds them.

The jaw crusher occupies a specific place in the size reduction landscape and its boundaries matter for specification. It is the primary machine: it takes the biggest, hardest feed and does coarse reduction, typically from boulders of up to 80 or 85 percent of the feed opening down to a product whose top size is set by the discharge gap. Downstream of it, cone crushers and gyratory machines perform secondary and tertiary reduction on the jaw's product, and hammer type machines reduce softer, less abrasive materials by impact; those machines are separate products with their own pages when a site needs them, and this page does not fold them in. Nothing on this page concerns packaging or paperboard testing, where the words crush and edge appear together in an entirely different industry: an edge crush test is a laboratory method for corrugated board strength, not a machine, and no crusher specification borrows from it.

Different buyers buy the same machine for different reasons. An aggregates quarry buys a primary jaw to open the pit's granite or basalt at 200 to 1,000 tonnes per hour and feed a closed circuit with screens and cones. A gold or copper mine buys a jaw primary, or a gyratory on the largest tonnages, ahead of the mill circuit. A recycling contractor buys a smaller, often mobile, jaw to turn demolition concrete and asphalt into reusable graded fill. An industrial minerals plant buys a jaw to reduce quartzite or feldspar ahead of grinding, with the crusher followed by dust collection and drying. The specification language differs, but the jaw physics is shared, and the paragraphs that follow keep all four buyers in view.

A short tour of named duties makes the machine concrete. In a hard rock quarry, dump trucks tip directly to a stationary primary with a grizzly or prescreen above it, and the crushed stream rides a belt conveyor to scalping screens and a secondary cone; a belt scale totals the tonnage and a metal detector guards the downstream. In a sand and gravel pit, a mobile jaw plant crawls with the face and feeds a closed circuit on tracks. In a demolition yard, an excavator feeds crushed concrete with rebar through a magnet equipped jaw plant that also carries an overhead magnet and a side discharge for steel. In each duty the same five knobs appear: feed size, setting, die profile, power, and protection against the uncrushable.

The purchase is never the crusher alone, and the RFQ that forgets the surroundings buys a bottleneck. Feed arrangement, trucks tipping to a hopper, an apron or pan feeder, or a direct excavator dump, decides whether the crusher receives a steady column of rock or the surges that half empty and flood it. Discharge arrangement, a conveyor under the machine with adequate clearance, or a grizzly ahead of it to scalp fines, decides whether the chamber clears and keeps crushing. Dust management on the feed and discharge, and the structural support that carries the dynamic loads of a machine whose eccentric works all day, complete the picture that a bare crusher price leaves out.

Chapter 2 / 06

How Compression Between the Jaws Does the Work

The crushing action is cyclic compression. As the eccentric shaft turns, the top of the moving jaw travels in a nearly circular path and the bottom in an arc, so the jaw approaches the fixed jaw and retreats once per revolution; typical eccentric speeds on production machines sit between roughly 200 and 350 revolutions per minute, falling as machines get bigger. Rock entering the top of the chamber is gripped, compressed, and fractured; the fragments descend by gravity as the jaw opens; and each successive grip further down the chamber reduces them again, until they pass the narrowest point at the bottom, the closed side, and leave as product. The chamber is in effect a converging channel whose geometry, set by the die profile, is a full stroke of design work by the manufacturer.

The nip angle governs whether the chamber can bite at all. It is the angle between the fixed and moving jaw faces at the point of grip, and if it exceeds the friction angle of the rock against the manganese, material rides up and out instead of being drawn down; crusher design keeps it typically in the high teens to low twenties of degrees, and die wear that flattens the corrugations effectively steepens it until the crusher loses bite and capacity. The feed rule follows the same geometry: maximum lump size is about 80 to 85 percent of the feed opening dimension, and a quarry that lets boulders approach or exceed the opening pays for it in bridging at the top and in the digging time lost to breaking them.

The closed side setting is the single number the operator controls most. It is the narrowest gap between the dies at the bottom of the chamber, measured on the closed side of the jaw, and it sets the product's top size in coarse terms: the product's maximum size runs roughly 1.3 to 1.8 times the setting depending on the rock and die profile, and the gradation curve behind that ratio is what the downstream screen circuit is designed around. Setting ranges on production machines span perhaps 50 to 250 millimeters, adjusted by shim packs or by a hydraulic setting adjustment system that also doubles as the uncrushable object relief on most modern machines.

Capacity follows setting, speed, chamber geometry, and the rock itself. A single model's data sheet presents a family of curves, tonnes per hour against closed side setting, for stated bulk densities and gradations: Metso's C Series literature and the per model pages such as the C106 sheet are the reference form, with capacities of a mid size machine running from a couple of hundred tonnes per hour at fine settings to well beyond at coarse settings, and the largest stationary primaries reaching several thousand. The honest comparison between vendors is made on the same setting, the same feed gradation and bulk density, and the same scalping arrangement, because prescreening the fines out ahead of the crusher is worth tens of percent of effective chamber capacity.

Wear is a designed consumption, not a defect. The manganese steel dies work harden under impact, starting around 200 Brinell in the as cast state and hardening at the surface to roughly 500 in service, so a die that looks worn flat may still be crushing efficiently until the chamber profile and nip are spent. Die life is quoted in tonnage and varies enormously by application: hundreds of thousands of tonnes between changes on moderate abrasive limestone, a fraction of that on abrasive granite and quartzite, and the plant's economics carry the wear cost per ton as a line item beside power and labor. Turning or swapping the dies, and eventually the toggle plate that protects the machine by breaking first, is the maintenance rhythm every jaw plant plans around.

Power draw and the drive train close the working picture. Installed motor power on production machines runs from tens of kilowatts on recycling jaws to several hundred on quarry primaries, driven through vee belts from a motor slide base or by direct coupling on larger machines, with the flywheel smoothing the cyclic load that would otherwise hammer the motor and the electrical system. Crushing force at the chamber translates to torque at the eccentric, and modern machines carry hydraulic overload protection that lets the moving jaw yield and pass an uncrushable, a crawler tooth, a tramp iron bar, without wrecking the frame, then reset automatically to the working setting. A vfd is uncommon on the crusher itself, whose speed is set by design, but appears on the feeders and conveyors around it, and a plc runs the interlocked start and stop sequence of the whole station.

Chapter 3 / 06

Crusher Types, Jaw Profiles, and Duty Boundaries

The single toggle design is the modern default: the moving jaw hangs directly on the eccentric, the pitman and toggle plate transmit the crushing force to the frame, and the elliptical jaw motion both crushes and transports material down the chamber with an up and forward stroke that promotes high capacity and a cubical product. The double toggle design, the older geometry, links the moving jaw through a pair of toggles so it moves in a purely swinging arc: less rubbing between rock and die, longer die life on abrasive duty, at the cost of capacity per unit mass and a taller frame. Most catalogs sold today are single toggle with some double toggle machines on specific abrasive duties, and the buyer's real choice is model size and die configuration, not toggle philosophy.

Stationary and mobile are the installation types, and they are different purchases. A stationary primary is a foundation, a feed structure, and a crusher chosen for the quarry's life, bought on tons per hour and wear cost, and served by haul trucks or a front loader; it wins every economy of scale. A mobile jaw plant, crawler or wheel mounted, carries the crusher, feeder, conveyor, and power pack on one frame, moves with the working face, and trades peak capacity and wear economy for elimination of haulage; demolition, construction, and small pits are its ground. Between them sit portable and skid mounted plants that relocate by crane or trailer as the project moves.

Crusher formTypical feed and dutySetting rangeWhere it wins
Stationary single toggle primaryquarry and mine run of faceroughly 50 to 250 mmCapacity, wear cost per ton, plant life
Double toggle jawhighly abrasive hard rocksimilar bandDie life on abrasive duty, less rubbing
Mobile crawler jaw plantdemolition, construction, small pitsroughly 20 to 150 mmMoves with the face, no haulage
Compact or laboratory jawsample reduction, small plants1 to 30 mmControlled small lot reduction

Jaw die profiles are the tuning hardware of the chamber. Corrugated toothed dies grip and promote a cubical fracture and are the standard on primary duty; flat dies give a more slabby product where the rock splits naturally; and steep or shallow profile variants trade capacity against top size control along the chamber. Die metallurgy is nearly always austenitic manganese steel in the 12 to 14 percent range with variants for impact and abrasion duty, and the trend across vendors is two piece or wedge mounted dies that change faster, because a primary's availability is set by the hours the mechanics spend in the chamber.

Duty boundaries against the neighbors deserve plain language. The jaw crusher is the primary: it takes the largest feed and does the first reduction. When the duty is secondary or tertiary sizing of the jaw's product, the machine is a cone crusher; when the rock is soft and low abrasion and single stage impact reduction suits it, the machine is a hammer type crusher; and on the largest mine tonnages a gyratory machine replaces the jaw at the face. None of those machines is this page, and a specification that describes primary reduction between a fixed and a moving jaw describes exactly this one. Around the primary, the balance of plant is its own engineering: the belt conveyor that takes the crushed stream, the belt scale that totals it, the vibrating or screw conveyor that moves fines where the circuit needs them, the cyclone separator and bag filter that collect the dust the crushing releases, and the centrifugal fan that pulls that dust system.

Chapter 4 / 06

Key Specification Parameters

Vendor quotations and data sheets revolve around a compact parameter set, and a buyer who reads them against the plant numbers can compare offers on engineering terms rather than on frame mass alone. The table below collects the parameters that decide performance for stationary primary duty, with the ranges a reviewing engineer should expect to see across a mainstream model range.

ParameterTypical specification rangeWhat it decides
Feed opening, width by depth400x600 to 1,600x2,000 mmLargest lump the machine can accept
Maximum feed size80 to 85% of openingPit or yard blast and demolition sizing rule
Closed side setting rangeroughly 50 to 250 mmProduct top size and capacity point
Capacity at settingtens to several thousand tphPlant throughput and model selection
Installed motor power30 to 500 kW classCrushing force margin and energy cost
Eccentric shaft speedroughly 200 to 350 rpmStroke rate and capacity balance
Nip angle in chamberhigh teens to low 20s degreesBite and self feeding of the chamber
Machine mass5 to beyond 100 tFoundation, crane, and structural scope
Setting adjustmentshim or hydraulic with reliefSetting change speed and tramp protection
Die metallurgy and profile12 to 14% manganese, toothed variantsWear rate, product shape, change interval

Two of those numbers do the selection work. Feed opening fixes the maximum lump, and the quarry's or yard's blasting and demolition practice, not the crusher catalog, sets what that number must be: a pit that produces boulders near two meters needs the biggest frames or a rock breaker above a smaller one. Capacity at setting fixes the model, and the comparison must be made on a stated feed gradation, bulk density, and scalping arrangement because those swing the curves by tens of percent; the honest basis is the vendor's curve family read at the buyer's setting, on the buyer's rock.

The remainder of the parameter set carries the plant around the crusher. Installed power decides the force margin on hard rock and the energy line in the cost per ton; machine mass sets the foundation and the crane plan for the install; the setting adjustment system decides whether a setting change is a maintenance event or a hydraulic button; and the die profile family decides product shape and wear cadence. On the drive side, the motor, belts or direct drive, and the flywheel energy storage belong to the vendor scope, while the feeder, conveyors, and dust plant around it are the buyer's boundary to define carefully in the RFQ so nothing falls between contracts.

Chapter 5 / 06

Selection Decision Factors and RFQ Language

Feed characterization comes first because every downstream number inherits it. The specification should state the rock type and its hardness and abrasiveness class, the feed gradation the blasting or demolition produces, the maximum lump size and its frequency, the moisture and clay content that promote chamber packing, and the tonnage per hour the plant must sustain with its seasonal peaks. Bulk density converts volume based estimates to the tonnes per hour the vendor curves quote. For recycling duty, the contaminant load, rebar, wire, timber, and the steel removal plan, is part of the feed definition, because tramp steel is the primary crusher's main abuser.

Product requirements come second because they set the setting and the circuit. State the required product top size and the gradation band the downstream screen or customer accepts, whether fines are scalped out ahead of the crusher with a grizzly or prescreen, and what the secondary and tertiary stages, if any, expect. The primary's job in most plants is not to make the final product but to open the rock for the next stage at an economic setting, and over specifying fineness at the primary buys wear and capacity for nothing. Stationary versus mobile follows the site plan: haul distance, face life, and the project calendar decide it, and the crusher choice narrows once that is fixed.

Selection factorWhat to specifyCommon mistake
Feed definitionrock class, gradation, max lump, tph, densityComparing capacity curves on different feed bases
Product targettop size, gradation band, scalping planBuying fineness at the primary the circuit does not need
Installationstationary or mobile, feed structure, layoutMobile bought where haulage is cheap and life is long
Protectiontramp relief, magnet, metal detectorNo steel removal ahead on demolition duty
Wear strategydie profile and metallurgy, change interval targetFlat dies on rock that needs toothed grip
Dust and environmentenclosure, water sprays, extraction scopeDust plant left out of both crusher and conveyor scope
Service accessdie change hours, platform and crane provisionsAvailability lost to slow chamber work

RFQ language that produces comparable offers follows from those factors and should read like a plant data sheet. State the feed and product definition with tonnage, the stationary or mobile basis, the setting range to be covered, the scalping arrangement provided, the tramp protection and steel removal expected, and the dust management scope boundary. Ask every vendor to state the capacity curve at the buyer's setting and feed basis, maximum feed size acceptance, installed power and drive arrangement, die mass and profile options with expected wear tonnage on comparable rock, setting adjustment method, machine mass and foundation loads, and the documented references on the same rock class.

Guarantees and acceptance close the procurement. A defensible offer guarantees capacity at the stated setting on the stated feed basis, states the maximum feed size the machine accepts, and commits to a wear parts consumption band on comparable duty measured over a defined tonnage. Hold every bidder to the same feed sheet, weight offers on cost per tonne including power, wear, and labor rather than machine price, and include a commissioning acceptance run at design tonnage with gradation measured on the product belt. The primary that meets its curve on the quarry's own rock, not on the brochure's, is the one that was specified honestly.

The balance of plant the RFQ must not forget: the feed hopper and grizzly or prescreen, the apron or pan feeder with its drive and vfd where surge control matters, the discharge conveyor with adequate clearance under the crusher and a belt scale for tonnage, the overhead magnet and metal detector on recycling and mine duty, the dust extraction with its cyclone separator and bag filter and the centrifugal fan that serves them, and the structural and electrical scope that carries a machine whose vibration the whole station feels. A vibration sensor on the crusher frame watches bearing health, and load cells under the feed hopper or a weigh feeder on reclaim complete the tonnage picture for plants that blend or meter downstream.

Chapter 6 / 06

Installation, Standards, Failure Modes, and Maintenance

Installation is a foundation and dynamics project. A stationary jaw transmits cyclic forces that a concrete foundation and its anchor bolts must carry for decades, with the vendor's dynamic load data driving the civil design; the feed structure, the discharge conveyor tunnel, and the crane access for die and component changes are decided at layout stage and expensive to fix later. Mobile plants trade that civil work for ground preparation and service access planning on the move. Commissioning runs the machine first empty, then loaded in steps to full feed, checking bearing temperatures, power draw against the curve, product gradation at the working setting, and the relief system's response to a test tramp.

Standards shape the machine's paperwork more than its geometry. Machine safety codes govern guards, interlocks, and the emergency arrangements around the drive and the chamber; electrical codes govern the motor and control scope in the plant's area classification; and structural codes govern the foundations and the feed structures. Vendor catalogs publish capacities on stated methodologies, and quarries with regulatory tonnage or dust limits carry those into their permits. A buyer does not need to cite clause numbers to specify outcomes: name the guarding and interlock expectations, the area classification, and the reference capacity basis, and hold the vendor to its own published curves.

Failure modeSignatureResponse
Die wear and profile losscapacity fall, slabby product, nip lossRotate or replace dies, review profile and metallurgy
Bridging at chamber topfeed hangs, machine runs emptyFeed sizing rule, rock breaker, grizzly adjustment
Tramp iron damagesudden overload, die or toggle eventRelief system check, magnet and detector upstream
Eccentric bearing failuretemperature and vibration riseLubrication audit, scheduled bearing replacement
Toggle plate breakmachine stops under overloadDesigned sacrifice: replace plate, find the tramp
Chamber packing with wet clayloss of compression, motor cyclingScalp fines, manage moisture, die profile change

Routine operation is trend led. Power draw at steady feed, bearing temperature, and the product gradation sampled on the discharge conveyor tell the operator how the chamber is wearing and when the setting has drifted; a vibration sensor program on the frame and bearings converts the same drift into condition based maintenance triggers. Die changes are the big scheduled event, planned by tonnage since last change and executed from the platform and crane provisions the layout bought, with the toggle and tension hardware inspected each time the chamber is open. Lubrication of the eccentric and toggle bearings, belt tension on the drive, and the feeder's wear liners make up the weekly rhythm.

The end state of a well specified jaw crusher is a primary station the quarry plans its week around instead of around which it must plan. The boulders go in, the crushed stream rides the conveyor at the tonnage the curve promised, the dies wear at the predicted rate and change in the predicted hours, the tramp events that close the shift are handled by a relief system instead of a repair crew, and the dust and steel that would poison the circuit are caught by the equipment around the machine. That is the whole product: a machine that opens the rock at a cost per tonne the plant can quote against.

FAQ

What is the closed side setting and why does it matter so much?

The closed side setting is the narrowest gap between the fixed and moving jaw dies at the bottom of the chamber, and it is the main variable the operator controls. It sets the product's top size, roughly 1.3 to 1.8 times the setting depending on rock and dies, and moves capacity inversely: a wider setting raises tonnage and coarsens the product. Modern machines adjust it with shims or hydraulically, and the hydraulic systems double as uncrushable object relief.

How do I estimate the capacity of a jaw crusher for my rock?

Read the vendor's capacity curves at your closed side setting, on your feed gradation and bulk density, with your scalping arrangement stated: Metso's C Series data and per model pages such as the C106 sheet are the reference form. Prescreening fines out ahead of the crusher is worth tens of percent of effective chamber capacity, so two vendors quoted on different scalping assumptions are not quoting the same machine duty. A commissioning run on your own rock settles it.

Single toggle or double toggle: which should I buy?

Single toggle is the modern default: the elliptical jaw motion gives higher capacity per machine mass and a cubical product, and it is what most current catalogs sell. Double toggle machines move the jaw in a pure swing with less rubbing between rock and die, which extends die life on the most abrasive duties at the cost of capacity and a taller frame. Most buyers are choosing model size and die configuration, not toggle philosophy.

Can a jaw crusher make the final saleable product in one stage?

On demolition and some aggregates duties a jaw at a moderate setting feeding a screen circuit produces a saleable graded fill directly. On hard rock for concrete and asphalt products the primary jaw opens the rock and the secondary and tertiary stages, cone machines on this class of rock, make the final gradation. Specifying the primary to do the circuit's whole reduction buys wear and capacity for nothing.

Stationary or mobile: how do I choose?

Haul distance, face life, and the project calendar decide it. A stationary primary on a foundation with a feed structure wins every economy of scale where the quarry lives for decades and trucks haul cheaply. A mobile jaw plant that moves with the face or the demolition site eliminates haulage and civil work and trades peak capacity and wear economics for that freedom; short life sites and urban recycling are its ground.

How long do jaw dies last, and what drives the wear rate?

Die life is quoted in tonnage crushed and swings an order of magnitude with rock abrasiveness: hundreds of thousands of tonnes between changes on moderate limestone, a small fraction of that on abrasive granite or quartzite. Profile, metallurgy, feed sizing, and the amount of fines let into the chamber all move it. The manganese work hardens in service, and the plant's wear cost per tonne, not the die price, is the number to specify against.

What happens when an uncrushable object enters the chamber?

Modern machines protect themselves by design. Hydraulic relief systems let the moving jaw yield and pass the object, a crawler tooth or a length of rebar, then reset automatically to the working setting; on shim adjusted machines the toggle plate is the designed sacrifice that breaks before the frame does. Magnet and metal detector removal upstream of the crusher is still the cheapest protection, because every relief event is wear and downtime even when it saves the frame.

Sources

  1. Metso: Nordberg C Series jaw crushers
  2. Metso: Nordberg C106 jaw crusher
  3. Sandvik: Stationary jaw crushers
  4. Metso: Nordberg C Series jaw crushers brochure (PDF)
Ask SpecForge AI