Cone Crusher

A cone crusher is a compressive size reduction machine in which a mantle, a conical crushing head gyrating on an eccentric, closes against a concave, the bowl liner, crushing rock between them in cycles of compress and release; the closed side setting, the narrowest gap at the discharge, sets the product top size. Cone crushers follow the primary stage, reducing jaw crusher product or run of quarry rock in secondary duty and shaping and finishing the product in tertiary duty, in closed circuit with a screen whose oversize returns to the crusher feed. Metso's cone crusher families, including the Nordberg HP series, are representative industrial catalogs, and this page treats the crusher and its circuit as the purchasing object.

This page is written for the plant engineer specifying a cone crusher for an aggregates quarry, a minerals concentrator, or a recycle crushing circuit. It works through what the machine does and what is being bought, how the mantle, throw, and setting do the work, which chamber and drive configurations fit which duties, the parameters that appear on vendor data sheets, and the selection factors and RFQ language that decide whether the installed crusher holds its tonnage and product shape through its liner life.

Bulk material conveyor hardware of the class that feeds and receives cone crusher circuits, shown as an installed belt conveyor

Photo: RICHI Manufacture, CC BY 4.0, via Wikimedia Commons

The decision concentrates in five places: the feed size and abrasiveness the upstream stage delivers, the product size and shape the market or downstream mill demands, the chamber profile and closed side setting that bridge them, the power and throw that drive reduction, and the automation and liner strategy that hold tonnage as liners wear. Get those right and the machine size, drive, and circuit screen follow.

Chapter 1 / 06

What a Cone Crusher Is and What Is Being Decided

The machine this page describes is a cone shaped compression crusher. Its main frame carries a vertical shaft on an eccentric so the shaft's axis nutates, swinging the mantle, the wearing head sheathed in manganese or martensitic alloy steel, toward and away from the concave, the bowl liner, around the full circle. Feed lands in the hopper or stone box, fills the crushing chamber, and rock is squeezed between mantle and concave each time the gap closes; crushed product falls through the discharge setting at the bottom. A hydraulic or mechanical set adjustment, often the hydroset system, holds the gap against tramp and uncrushable objects, releasing and resetting rather than breaking, and the bowl or jack screws set the nominal chamber.

What is being decided when a cone crusher is purchased is a tonnage and product guarantee backed by a liner wear statement. The buyer is purchasing a stated tonnes per hour of a stated material from a stated feed top size to a stated product size distribution, commonly expressed as the setting that yields a given percent passing, with a product shape the aggregates market can sell, at liner lives and power draws that hold the operating budget. Everything on the vendor data sheet, frame size, power, eccentric throw options, chamber profile, setting range, exists to support those guarantees, and the honest vendor sizes from crushing test data and gradation curves rather than from a tonnage table alone.

The cone crusher sits in the comminution family with defined neighbors. It is not the jaw crusher at the head of the circuit, which breaks run of quarry rock by compression in a V opening and sets the stage; the jaw crusher page already names the cone crusher as its downstream partner, and this page is that downstream machine's authority. It is not a gyratory crusher, the primary duty machine whose full shaft gyrates in a spider bearing, a neighbor left for its own topic. It is not an impact crusher, which breaks by striking and suits cubical shape and recycle duty at higher wear cost on abrasive stone. And it is not a grinding mill: the ball mill takes over below the crushing sizes where compression between machine surfaces stops paying.

Different buyers buy the same machine for different products. An aggregates producer buys secondary and tertiary cones to make road stone and concrete aggregates with shape and gradation the specification pays for. A base metal concentrator buys a secondary cone in closed circuit feeding the SAG or ball mill train at the transfer size the grinding circuit wants. An iron ore plant buys coarse and fine cones ahead of concentrate production. A recycle operator buys cones for demolition concrete with reinforcement protection on the mind. The specification language differs, but the compression physics is shared.

The economics deserve their own paragraph because liners and power are the budget. Manganese and alloy steel liners consume at grams per tonne, and a liner change is an outage measured in shifts; power runs the plant's main motors at tens to hundreds of kilowatts per hundred tonnes; and the product shape penalty, flaky product the market discounts, costs more than either on some benches. The honest comparison prices tons per liner set, kilowatt hours per tonne, and the shape the chamber actually delivers, and the cheapest frame at the biggest number on the brochure is rarely the cheapest crusher over its liner life.

A short tour of named duties makes the machine concrete. In a granite quarry, jaw product at 150 millimeters feeds a secondary cone at a 38 millimeter setting in closed circuit with a vibrating screen, making road base. In a copper concentrator, cone product at 12 millimeters feeds the SAG mill feed stockpile at 3000 tonnes per hour on the largest machines. In a sand and gravel plant, a tertiary cone at a 10 millimeter setting shapes the product the asphalt market pays a premium for. Each duty names the same knobs, chamber, setting, throw, and liner, with numbers that scale while the gyrating head barely changes.

Chapter 2 / 06

How the Mantle and the Setting Do the Work

Compressive breakage is the mechanism: rock loaded between mantle and concave fails in tension under compression, cracks propagating from particle contacts, and the bed of particles in the chamber also inter particle crushes, particle against particle, in choke fed conditions. The chamber geometry walks material down as it breaks, each gyration closing the gap and squeezing a slice of the bed, and the closed side setting, CSS, is the narrowest discharge gap on the closed side of the circle, the number that most directly governs product top size: coarser setting, coarser product; finer setting, more fines, more power, slower tonnage.

Eccentric throw and speed set the crushing rate. Throw, the swing amplitude of the mantle, larger in secondary coarse chambers and smaller in fine chambers, decides how far material drops per gyration and how coarse the feed the chamber can accept; speed, gyrations per minute, sets how many compressions per second the bed sees, with modern machines running 300 to 800 or more depending on size and duty. The pairing of throw and chamber with the material's abrasiveness decides both capacity and liner wear pattern, and vendors offer throw options per frame so one machine can be tuned from secondary coarse to tertiary fine.

Choke feed is the operating discipline that makes the machine an inter particle crusher. With the chamber kept full by a regulated feed, a level control or a feeder rate matched to the crusher, particles crush against each other, product shape improves to cubical, liner wear spreads evenly, and tonnage stabilizes; fed starved, the same machine slabs stone between bare liners, wears rings into the metal, and makes flaky product. The feed arrangement, surge bin, feeder, and the stone box that centers feed into the chamber, is thus part of the crusher purchase, and the plant that runs a cone starved is paying for a cone and receiving half of one.

Tramp protection and setting control keep the machine alive. Uncrushable steel, bucket teeth, drill steel, enters every quarry feed, and the hydroset or equivalent system lets the mantle yield, pass the object, and return to setting automatically; older designs used spring releases with an outage to reset. The same hydraulic system measures and adjusts CSS on the run in modern machines, compensating liner wear without stopping the feed, and pairs with power draw and level sensors for automation: closed loop control of feeder rate to hold power, and of setting to hold product size against wear. A crusher bought without its automation package is a machine the operator cannot hear over the noise.

Liners are the wearing heart, and their metallurgy is a material match. Manganese steel work hardens under impact and suits most stone; martensitic alloys hold their profile better in abrasive rock and fine chambers; ceramic inserts extend life in the highest wear zones of the concave. Liner profiles, coarse, medium, fine, and the extra coarse options, trade feed opening against reduction: a coarse chamber takes bigger top size with less reduction, a fine chamber chokes quickly on coarse feed but finishes product. The wear pattern tells the tuning story: ring porosity in the upper concave means feed too coarse or starved, and a worn lower mantle lifts the product top size long before the liner is spent.

The circuit closes the loop. A screen on the crusher discharge, in most aggregates plants a vibrating screen, splits product from oversize, and oversize returns by conveyor to the crusher feed bin; the circulating load buffers feed surges and lets the setting run finer at the same tonnage. In concentrators the cone may run open circuit into the SAG feed stockpile. Feed metering from the upstream stage, a weigh feeder or belt scale on the feed conveyor for metallurgical accounting, and level sensing on the crusher bin, are the circuit's nervous system, and their absence shows as tonnage swings and liner damage.

Chapter 3 / 06

Chamber Types, Circuit Positions, and Duty Boundaries

Configuration choice begins with circuit position. Secondary duty, taking jaw or primary product at top sizes to 150 millimeters and above on the largest frames, wants coarse or extra coarse chambers, high throw, and robust frames; tertiary duty, shaping and finishing at settings down to 6 or 10 millimeters, wants fine chambers, lower throw, and automation to hold the setting. The same frame often serves either with a chamber and throw change, which is why frame size and power, not chamber, define the machine purchase. Between them sits the shredder or quaternary shaping duty of the sand market, running extra fine chambers at tight settings in closed circuit.

PositionChamber classTypical feed topSetting range
Secondarycoarse, extra coarse100-350 mm19-50 mm
Shaping tertiarymedium50-150 mm13-32 mm
Fine tertiaryfine25-80 mm6-16 mm
Quaternary sandextra fine10-40 mm6-10 mm

Duty boundaries keep the selection honest. The cone is not a primary machine: run of quarry boulders belong to the jaw crusher, or a gyratory on the largest mines, before any cone sees them, and feeding a cone beyond its chamber top size bridges the machine and wears rings in the liners. It is not a grinding machine: below the finest settings the ball mill circuit owns size reduction, and the cone's job ends at the transfer size. It is not an impact alternative: on abrasive stone the impactor's wear cost loses badly, while on soft recycle material the impactor's cubical shape may win. Within its band, from hundreds of millimeters feed to millimeters product, the cone is the industry's standard reducer.

Where it sits in the plant matters as much as the machine. Upstream, the primary crusher and the surge bin set the feed the cone receives, and a conveyor with belt scale meters it; the bin needs level control to keep choke feed through surges. Downstream, the closed circuit screen and its return conveyor set the tonnage loop, and the product conveyor and stockpiles take the finished gradation. Dust collection, a bag-filter or central extraction on the crusher house, and water spray suppression, address the dust the compression makes, and the enclosing building decides the neighborhood relationship. The cone is bought as a circuit position, and the RFQ that buys only the frame buys the least of it.

Stationary and portable installations share the machine. Aggregates plants build stationary cones on tall foundations with steel-lined chutes and screen towers above; recycle and contract crushing run the same frames on wheeled or tracked portable plants where the screen, conveyors, and feeder close around the crusher in one unit. The machine's fundamentals, chamber, setting, throw, liner, do not change with the mounting; what changes is the civil scope and the feed arrangement discipline, and portable plants have their own choke feed challenges the RFQ should name rather than assume.

Chapter 4 / 06

Key Specification Parameters

The data sheet parameters fall into four groups: capacity and product, mechanics, wear, and protection. Capacity parameters are throughput at a stated setting and feed gradation, the product size distribution at that setting, and maximum feed size the chamber accepts. Mechanical parameters are frame size, installed motor power, eccentric throw options and speed, and the set adjustment system. Wear parameters are liner metallurgy options, expected liner life in hours or tonnes at the stated duty, and change time. Protection parameters are the tramp release system and its clearing stroke, the automation package's sensing and control loops, and the power and level instrumentation. A quotation that quotes tonnage without the setting and gradation basis is not comparable to one that states them.

ParameterTypical rangeDesign note
Frame power75-1000+ kWFrame size proxy
Capacity50-3000+ t/hSetting and duty dependent
Closed side setting6-50 mmProduct top size governor
Max feed sizechamber dependent80-90% of feed opening
Eccentric throwoptions per frameCoarse vs fine tuning
Reduction ratio4-6 typical, to 8Per stage, chamber set
Liner life300-2000 hAbrasion and duty set it
Tramp systemhydraulic releaseAuto reset on modern frames
Automationpower, level, CSS loopsHolds tonnage as liners wear

Product curve and shape deserve explicit numbers in every specification because they are the contract. The vendor should state the expected product percent passing at the quoted setting for the supplied feed gradation, the shape indices where the market cares, flakiness or shape index on aggregates duty, and the circulating load implied with the circuit screen. Screening test or breakage characterization data on the actual material lets the vendor model rather than guess, and the buyer should demand the basis. Specifying a cone by tonnage alone invites the vendor to quote the coarsest setting that number supports and let the screen circuit absorb the difference.

Power draw and the drive round out the sheet. Motor power sets the frame's ceiling, and the operating draw at choke feed tells the truth about the duty: a cone drawing 60 percent of rated power is running loose, and one pinned at full draw with a climbing bowl is running beyond its chamber. Drives are direct with V belt or direct coupled, with soft start and, increasingly, variable frequency for tuning throw speed to the material. The power signature per tonne, kilowatt hours per tonne at the setting, is the number that follows the machine for its life and belongs in the bid table next to the liner figures.

Standards and safety close the sheet. Machinery safety practice governs guarding on the drive, the countershaft, and the feed hopper lip, with lockout provisions for liner work; the tramp release and counterbalance systems are safety functions and their test regime is part of commissioning; and dust and noise limits, occupational and environmental, set the enclosure and suppression scope. Structural loads, the crusher's crushing forces into the foundation, are a civil interface the vendor documents early. None of these are exotic, but the countershaft guard and the liner change tooling are the two items most often discovered missing at the first shutdown.

Instrumentation deserves its own rows on the data sheet because automation only holds what it can measure. The power transducer, the level sensor in the feed chamber, and the position feedback on the hydraulic set adjustment are the control loops' eyes; the load cell or weightometer on the feed conveyor closes the tonnage account against which specific energy is computed; and product moisture on washed circuits, or dust suppression flow, is watched where the permit or the market pays for it. A crusher plant that meters feed and power can prove its kilowatt hours per tonne weekly, and that number is the one that follows the machine for its life. Where the product runs to stockpiles or to a rotary dryer on the aggregates line, the survey samples that close the mass balance belong in the same routine, because a circuit that measures itself is a circuit that can be tuned.

Chapter 5 / 06

Selection Decision Factors and RFQ Language

Selection starts from the material and the circuit position. The designer writes the material and its abrasiveness, the feed size distribution the upstream stage delivers, the product size and shape the market or the grinding circuit demands, the tonnage and its future profile, and the circuit architecture, closed with a screen or open to a stockpile. From that basis, frame size, chamber, and throw follow with little freedom. An RFQ without the feed gradation and the product spec invites vendors to quote the frame that fits their stock rather than the duty.

Duty driverFavored configurationWatch item
Aggregates secondarycoarse chamber, high throwShape spec, screen loop sizing
Aggregates tertiaryfine chamber, automationSetting drift as liners wear
Concentrator secondarycoarse chamber, high tonnageTransfer size to grinding
Sand shaping quaternaryextra fine chamberCirculating load and power
Recycle concretemedium chamber, steel riskTramp steel frequency, release

Chamber and throw pairing is the second decision and it is made with the material's abrasiveness. Coarse feed on abrasive stone wants high throw coarse chambers that open the top and pass tonnage; fine finishing wants low throw fine chambers that hold setting and shape. The liner metallurgy follows: manganese for impact and toughness, martensitic for abrasive wear holding, ceramic enhanced zones where the wear map says. The vendor should propose the pairing with the wear prediction and the product curve, and the buyer should treat the pair as the machine, because the same frame with the wrong chamber is the wrong crusher at the right price.

Automation is the third decision and it is what holds the guarantee between liner changes. Power draw control on feeder rate, level control in the chamber, and CSS compensation on wear keep tonnage and product within band through the liner life, and the alarm and trip philosophy protects the machine on tramp events and overload. The instrumentation, sensors, drives, and the control narrative, belongs in the crusher purchase package, and the plant's control system integration is a scope line the RFQ must draw. A modern frame without its automation is a tonnage guarantee no one can hold.

The RFQ language that returns comparable offers states the material and the numbers demanded. State material and abrasiveness class, feed size distribution, required product size and shape spec, design tonnage and headroom, circuit architecture with screen aperture, tramp steel expectation, dust and noise envelope, and the performance basis, product curve at setting, power per tonne, liner life. A complete RFQ paragraph reads: secondary cone for granite, feed 0 to 125 millimeter at 400 tonnes per hour, product 0 to 32 millimeter with flakiness below 20 percent, closed circuit on a 32 millimeter screen, martensitic liners with 1200 hour expected life, automation holding CSS on wear, dust to site permit.

Commercial comparison is only fair on a normalized basis. Offers should be forced onto one table: frame and power, chamber and throw proposed, product curve at the stated setting, circulating load implied, liner metallurgy with predicted life and price per set, change time and tooling, automation scope, tramp system behavior, delivery, and spares. The cheapest frame is very often the one with the thinnest liner prediction, and its operating cost lands in the crushing house every shift of its life. Where the market pays for shape, the shape column outranks the price column outright.

Chapter 6 / 06

Installation, Standards, Failure Modes, and Maintenance

Installation is a heavy mechanical and civil erection. The crusher foundation takes the crushing forces and vibration with anchor design per the vendor's load document; the frame sets and grouts, the countershaft and drive align, the bowl and mantle install with the setting checked against the shims or hydroset reference; and the feed arrangement, surge bin, feeder, and stone box, builds to center the feed and keep it choked. Commissioning runs empty checks on rotation and release systems, then feed at ramp with the automation tuned, sampling the product curve at setting and logging the birth certificate: tonnage, power, curve, and liner baseline.

Failure modes have a known hierarchy. Liner wear through, the routine consumable, shows as product top size drift and finally as steel on steel ring bellowing; tramp events that exceed the release, or repeated releases with steel in the feed, distress the release system and the head assembly; countershaft bearing and gear wear announce in temperature, vibration, and backlash; the eccentric and head bushing wear shows as a dropped setting drift and gyration signature; and structural events, cracked frames or main shaft breaks, are rare fatigue or overload consequences. On the process side, bridge and starvation events damage liners and tonnage both. Nearly all announce themselves in power draw, product curve, and vibration trends.

SymptomLikely causeFirst response
Product top size drifting upliner wear or setting driftCSS adjust, plan liner change
Power pinned at full drawoverfed or wet sticky feedFeeder rate, feed audit, screen check
Frequent tramp releasessteel in feedMagnet and magnet check upstream
Bearing temperature risinglube or wear faultLube system service, vibration survey
Setting dropping on its ownhydroset or bushing wearSystem check, clearance survey

Maintenance is planned around liners and the lube system. Liner changes at predicted tonnes, with the mantle and concave renewed as a set and the wear profile surveyed at each change; lube oil sampling and filter service on schedule with the crusher's oil station a monitored system; countershaft and eccentric clearances surveyed at liner changes and corrected before they become failures; and the tramp release system proof tested on interval. The liner change shift, tooling, lifting, and crew, is the availability number, and plants buy the clamping and lifting tooling with the machine rather than after the first outage.

Operational stewardship is what the purchase actually bought. Operators who hold choke feed through surges, who trend power and product curve against liner life, and who pull the steel out upstream with magnets before it reaches the chamber, run cones to their quoted tonnage between planned liner sets; operators who feed by convenience wear rings in the liners and flaky stone into the stockpile. The crushing house trend board, tons, power, setting, curve, and liner hours, is the crusher's real price tag, and reading it weekly keeps the secondary circuit from becoming the plant's excuse.

The utilities around the frame finish the purchase. Crusher drives are large induction motors started against a broken ore load, and modern plants fit a variable frequency drive or soft starter both to protect the mechanical train and to trim speed to chamber and material; water supply for dust suppression and seal flushing is metered, commonly with an electromagnetic flow meter, because both the permit and the machine's seals depend on it. Dust extraction from the crushing house runs to a bag filter or central collector, and on wet circuits the fines report to a slurry pump and sump rather than to the air. Around it all, the quarry's mobile fleet, the excavator that digs and the trucks that haul, set the feed the crusher actually receives, which is why the honest RFQ describes the circuit, not just the machine: a cone matched to a steady, screened, metered feed outperforms the same cone fed by surprises.

FAQ

What does the closed side setting control on a cone crusher?

The closed side setting, CSS, is the narrowest gap between mantle and concave at the point of closure, and it is the main governor of product top size: a tighter setting makes finer product at higher power and lower tonnage, a coarser setting the reverse. Modern machines adjust it hydraulically while running and the automation compensates liner wear to hold the setting. Quoted tonnage without the setting and gradation basis is a number without a meaning.

What is the difference between a cone crusher and a jaw crusher?

The jaw crusher is the primary machine, breaking run of quarry rock by compression in a V opening at the circuit head, and the cone crusher follows it, reducing jaw product in secondary and tertiary duty with a gyrating mantle inside a concave that runs continuously and at higher reduction per installed power. The jaw sets the stage; the cone finishes it. In a typical quarry the jaw's product is the cone's feed, and the live jaw crusher page already points here as the downstream neighbor.

What is choke feed and why does it matter?

Choke feed keeps the crushing chamber full so particles crush against each other, inter particle crushing, rather than striking bare liners. It improves product shape to cubical, spreads liner wear evenly, stabilizes tonnage, and protects the machine from slabbing flaky product. It is achieved with a surge bin and a feeder rate matched to the crusher, watched by level control. Running a cone starved is the single most common way plants lose liner life and product spec at the same time.

How long do cone crusher liners last?

Liner life runs from a few hundred hours in highly abrasive hard stone fine chambers to a couple of thousand hours in gentle duty, set by material abrasiveness, chamber and setting, throw, and feed discipline. Metallurgy moves it: manganese work hardens under impact, martensitic alloys hold profile in abrasive duty, and ceramic inserts extend the highest wear zones. The vendor should predict life in tonnes for your material, and the plant should verify by survey and plan the change, because running liners to failure rings the metal beneath.

Can a cone crusher make sand?

Yes, quaternary and shaping duty on extra fine chambers at tight settings, in closed circuit with fine screens, manufactures crushed sand with cubical shape that natural sand markets accept. It is power hungry and circulating loads run high, so the economics rest on the sand price and the screen circuit's efficiency. The shaping duty is one of the reasons fine chambers and automation on setting hold such value in aggregates plants.

How does a cone crusher handle uncrushable tramp steel?

The hydraulic release system lets the mantle yield and pass the object, then return automatically to setting, where older spring designs needed an outage to reset. The release stroke and clearing capacity are frame design data, and repeated tramp events still distress the head and release systems, so magnets upstream of the feed are standard protection. The release proof test belongs in commissioning and at intervals thereafter.

What power does a cone crusher draw per tonne?

It varies with material, setting, and chamber, but secondary and tertiary cone duty commonly lands in the range of roughly 0.5 to 1.5 kilowatt hours per tonne crushed, finer settings and harder stone at the top of the band. Power draw at choke feed is also the machine's health signal: drawing far below rating means loose running, pinning at full draw with climbing pressure means the chamber is beyond its duty. The kilowatt hour per tonne figure at the quoted setting belongs in every bid table.

Sources

  1. Metso, Cone crushers
  2. Metso, Nordberg HP Series cone crushers
Ask SpecForge AI