Selective Catalytic Reduction

Selective catalytic reduction, SCR, is the post combustion technology that removes nitrogen oxides from flue gas by injecting ammonia or urea into the gas stream and passing it over a catalyst, where the NOx reacts with the ammonia to yield nitrogen and water: the pollutants leave as atmosphere. On utility boilers, gas turbine heat recovery steam generators, industrial furnaces, cement and glass kilns, and chemical plant heaters, SCR is the deep reduction workhorse, delivering 70 to 95 percent NOx removal at the stack where combustion tuning and staged firing have reached their limits. This page is the stationary source machine, the reactor and reagent system bolted to a flue gas duct; the mobile source cousin on diesel engines shares the chemistry and not the engineering.

This page treats the SCR system as a purchasing object: how inlet NOx and the required outlet size the catalyst volume, how the temperature window places the reactor in the flue gas train, how reagent choice, anhydrous ammonia, aqueous ammonia, or urea, shapes the balance of plant, and how ammonia slip, catalyst pitch, and dust management dominate the operating story. It is a reduction machine: the thermal oxidizer and the catalytic oxidizer on related pages destroy VOCs by oxidation, and confusing the two buys the wrong box with the right acronym.

Industrial plate and passage heat transfer equipment in a plant, representative of the plate catalyst module and flue gas equipment class that SCR reactors are built from

Photo: Renegade, Public domain, via Wikimedia Commons

The decision concentrates in five places: the flue gas flow, temperature, and NOx and dust burden, which size and place the catalyst; the outlet NOx and ammonia slip the permit demands; the reagent, anhydrous, aqueous, or urea, and its storage and delivery; the duct space and pressure drop the fan can give; and the fouling and poisoning regime that sets catalyst pitch and life. Get those right and reactor size, catalyst layers, and injection design follow.

Chapter 1 / 06

What a Selective Catalytic Reduction System Is and What Is Being Decided

The chemistry is short and selective: ammonia, NH3, reacts with nitric oxide and nitrogen dioxide over a catalyst at flue gas temperature to produce nitrogen and water, and the word selective is the whole point, because the ammonia reduces NOx rather than oxidizing to NOx itself, as a flame would. In practice the system is an injection grid and a reactor: an ammonia injection grid, AIG, of pipes and nozzles across the duct delivering the reagent mixed with carrier air, a mixing length that evens it into the flue gas, and a reactor vessel holding one to four layers of catalyst, titanium tungsten vanadium oxides in the standard honeycomb or plate form, sized to give the gas its few seconds of residence at temperature. Downstream, the ash hopper and the fly ash handling deal with what the reactor catches, and the stack sees nitrogen and water where NOx was.

Where the machine goes in the flue gas train is half its engineering, because the temperature window decides. The standard vanadium catalyst works between roughly 300 and 420 deg C: below about 300 the reaction slows and ammonia slips through unreacted, above about 420 the ammonia starts oxidizing to NOx itself and the catalyst sintering clock runs. High dust locations, right after the boiler economizer and downstream of the industrial burner's furnace work, sit in that window and pay with ash fouling and erosion; tail end locations, after the dust collector and reheated, pay with reheat fuel and gain clean gas and longer catalyst life. The gas turbine hrsg placement, in the middle of the tube banks where exhaust temperature lands in the window, is its own integration discipline, and the reactor position is chosen with the heat recovery steam generator's whole design.

What is being decided, in purchasing terms, is five things. First the duty: flue gas flow and temperature, inlet NOx, the outlet the permit demands, and the dust and sulfur species that ride along. Second the reactor: how many catalyst layers, initial plus spare, in what pitch, and where it sits in the train. Third the reagent: anhydrous ammonia, aqueous ammonia, or urea, each with its storage, safety, and delivery story. Fourth the injection and control: the AIG design, the mixing, and the control philosophy that meters reagent against NOx with slip as the constraint. Fifth the balance: pressure drop allowance, ash handling, and the catalyst management plan, activation, testing, replacement, that carries the plant through the catalyst's life. The paragraphs that follow work these in order.

A scale tour grounds the machine. A package boiler at a chemical plant carries a small wall mounted reactor and a skid of urea to 50 cubic meters of flue gas. A gas turbine combined cycle hrsg carries a reactor the size of a small building with two layers of catalyst and a 28 percent aqueous ammonia system. A coal unit carries a high dust reactor with ash hoppers, soot blowers, and a catalyst handling crane. The chemistry is the same at every scale, and the engineering is the dust, the slip, and the reagent discipline. The reactor, its reagent skid, and the induced draft centrifugal fan that carries the gas through the added pressure drop are one system on one duct budget, bought as one integration decision.

Chapter 2 / 06

How Ammonia, Catalyst, and the Temperature Window Do the Work

The reaction wants stoichiometry and time. One mole of ammonia per mole of NO in the dominant reaction, with a little more for the dioxide fraction, injected as vapor and mixed to uniformity before the catalyst face; the design stoichiometric ratio, NH3 to NOx, runs 0.8 to 1.0, deliberately short of complete so that unreacted ammonia stays small, and the fraction that passes through unreacted is ammonia slip, the permit's second number after outlet NOx. Slip limits run 2 to 5 ppm class on modern permits, sometimes lower near sensitive fly ash markets, because slipped ammonia salts with flue gas sulfur and absorbs into fly ash, contaminating its sale as cement additive, and the slip constraint, not the NOx conversion alone, is often what sizes the catalyst.

Catalyst volume follows from area velocity, the flue gas flow divided by catalyst geometric surface area, the industry's sizing currency, crossed with the required conversion and the activity the catalyst has left. Fresh vanadium titanium catalyst removes most of the NOx crossing it in a fraction of a second of true surface residence; as poisons, arsenic and calcium in coal ash, alkali salts in biomass, phosphorus in oil firing, occupy active sites, activity decays and the plant adds layers or replaces spent ones, and the design provides the initial layers plus the spare layer space to restore performance without replacing everything. The activation and replacement schedule, a few years per layer by fuel and dust, is the lifecycle economics of the machine and belongs in the bid's commercial terms.

The temperature window is guarded by the plant's own load swings. Boiler load moves gas temperature through the window's edges at low load, cold, and upset, hot, and the design answers with the position it chose: economizer bypasses to warm the gas at low load, tempering air to cool it at high, or simply the acceptance that low load means less NOx anyway and the reactor exits service below the window's floor. On hrsg duty the gas turbine's exhaust sits squarely in the window across its load range, one reason that application is so clean, and supplemental firing downstream moves the reactor placement arithmetic with it.

Mixing is the hidden half of the performance. Ammonia injected at 5 percent concentration in carrier air must be distributed across the duct to a few percent uniformity at the catalyst face, and the AIG's nozzles, zoning, and the static mixers or turning vane provisions behind them exist for that number; maldistributed reagent means high slip over here and unreacted NOx over there, the classic stack pattern that tuning chases with AIG zone balances. The commissioning activity that matters most on any SCR is the grid tuning, mapping NOx and ammonia across the duct and balancing injection zones, and the specification should carry the tuning as a deliverable with a uniformity acceptance number.

Sulfur's side chemistry sets the fouling story on coal and oil duty. Sulfur dioxide oxidizes slightly on the catalyst to sulfur trioxide, which combines with slipped ammonia to form ammonium bisulfate, a sticky salt that condenses in the cooler back end, fouls air heater baskets and catalyst pores, and forces the balance between conversion and slip on one side and bisulfate deposition on the other; the design manages it with slip limits, catalyst formulation that suppresses SO2 to SO3 conversion, and soot blowing intervals that keep deposits moving. The ash hopper below a high dust reactor, the soot blowers on the catalyst layers, and the fly ash ammonia content monitoring complete the housekeeping that this chemistry demands.

A worked sizing example makes the currency concrete. Take 500,000 cubic meters per hour of flue gas at 350 deg C carrying 200 milligrams per normal cubic meter of NOx down to 40: the removal is 80 percent, the reagent demand follows stoichiometry at roughly 0.85 ratio, and the catalyst volume settles where the chosen area velocity meets that conversion at end of life, several hundred cubic meters of honeycomb on a plant this size, pitched coarse if the ash is fine. Every term in that sentence is a line in the RFQ, and the vendor's job is to make them meet at a price; the buyer's job is to notice that the same gas with a 3 ppm slip limit instead of 5 grows the reactor a visible percent, because slip, not NOx, was sizing the machine all along.

Chapter 3 / 06

Reagent Systems and Reactor Placements and Duty Boundaries

Anhydrous ammonia is the concentrated reagent: delivered as liquid under its own vapor pressure, stored in pressure receivers, vaporized and diluted with air before injection, the cheapest per ton of NOx removed and the most regulated per ton stored, with toxic release dispersion analysis, water spray mitigation, and siting distance that some sites cannot accept. Aqueous ammonia at 19 to 29 percent trades most of the hazard for most of the convenience: atmospheric storage, pumps, and a vaporizer or heated air stream to release the ammonia, standard on gas turbine plants and the middle of the market. Urea is the benign molecule: granular or liquid, stored like fertilizer, converted to ammonia on site by hydrolysis or by direct injection and thermolysis in the hot duct, safest to handle, highest in balance of plant, and increasingly the default where regulations on anhydrous storage tighten, the reagent decision is a safety and logistics decision first and a cost decision second.

Reactor placement splits the market into three camps. High dust, ahead of the particulate collector, keeps gas temperature in the window for free and pays with catalyst wear and fouling, the coal plant standard with its erosion classed pitch and blowers. Low dust, after the electrostatic precipitator or bag filter, cleans the fouling problem and cools the gas out of the window, paying with reheat, a fuel or steam line that tail end SCR on some plants carries. Tail end after the wet scrubber adds the sulfur cleanup upstream and the lowest catalyst wear, again with reheat; the flue gas desulfurization trains and the SCR arrange themselves in these orders by fuel and economics, and the placement is the first integration decision of the project.

Duty boundaries against the neighbors deserve plain language. This machine reduces NOx with a reagent and is not an oxidation device at all: the thermal oxidizer and the catalytic oxidizer destroy VOC and HAP by oxidation, a different chemistry, a different pollutant, and a page each of their own, and a plant with both duties runs both systems, sometimes in the same duct train in series. It is not the dry scrubber, which removes acid gas with injected sorbent, though the two share flue gas real estate on coal plants and their ash streams interact. It is not SNCR, selective non catalytic reduction, the same ammonia chemistry run without catalyst at higher temperature in the furnace, cheaper and shallower, 20 to 50 percent removal versus SCR's 70 to 95, and the honest selection often runs SNCR alone for modest targets or SNCR plus SCR in series for deep ones.

The hrsg integration deserves its own paragraph because that market is enormous. The SCR reactor sits in the exhaust duct between tube banks, the gas turbine's 500 plus deg C exhaust cooled to the window by the upstream superheater and evaporator banks, and the reactor's location in the hrsg design is coordinated with the boiler maker from the start, the tube bank spacing, the catalyst access, the duct work, one engineering package. Combined cycle plants with supplementary firing move the window and the reactor with it, and the SCR vendor and the hrsg vendor's interface document, who sizes, who supplies the reactor shell, who guarantees the pressure drop, is a real deliverable the project should name.

ArrangementReagent typicalWhere it winsWatch-outs
High dust reactorAnhydrous or aqueous NH3Coal and oil units, window in reachErosion, fouling, blowers, ash ammonia
Low dust after precipitatorAqueous NH3 or ureaCleaner catalyst life on dusty fuelReheat energy to reach the window
Tail end after scrubberUrea commonCleanest gas, longest catalystReheat fuel, largest energy penalty
HRSG embeddedAqueous NH3 typicalGas turbine combined cyclesBoiler interface coordination
Chapter 4 / 06

Key Specification Parameters

The specification is built from the permit backward. The process set states flue gas flow at reference conditions, temperature range across load, inlet NOx with the basis, dust loading, sulfur dioxide and trioxide, and the fuel's poison inventory, arsenic, calcium, alkali, phosphorus. The performance set states outlet NOx and ammonia slip with averaging periods, the NOx removal efficiency, and the fly ash ammonia limit where ash is sold. The design set states catalyst type and pitch, layers initial plus spare, area velocity basis, and pressure drop allowance. The reagent set states the reagent choice and its storage, delivery, and vaporization scope. The commercial set states catalyst life guarantee, activity test protocol, layer addition and replacement pricing, and the tuning deliverable.

ParameterTypical rangeWhy it matters
NOx removal efficiency70 to 95 percentThe permit number the reactor exists for
Ammonia slip limit2 to 5 ppm, lower on ash salesOften the sizing constraint, not NOx
Catalyst temperature window300 to 420 deg C standardPlaces the reactor and its load range
Area velocitySizing currency, m/hFlow over catalyst area, the volume lever
System pressure drop5 to 15 mbar by designFan energy and capacity allowance
Catalyst pitch3 to 9 mm by dustFouling standoff versus volume
Reagent ratio NH3 to NOx0.8 to 1.0Conversion versus slip balance
Catalyst layer life2 to 6 years by fuelLifecycle replacement economics

Two lines in that table deserve the sharpest pencil. Ammonia slip, because it is the constraint that sizes the catalyst on most modern systems and the number the neighbors' fly ash sales and the air heater's fouling feel first, and the guarantee should state it at end of layer life, not at commissioning. Catalyst pitch and life, because the dust in the gas sets both: fine high ash coal demands coarse pitch, coarse pitch costs volume, volume costs money and pressure drop, and the honest trade is made on the fuel analysis actually fired rather than the design coal.

Instrumentation closes the machine and it is the control loop's eyes: NOx analyzers before and after the reactor, an ammonia analyzer at the stack or the slip point where continuous monitoring is demanded, gas temperature transmitters ahead of the reactor and across the window, a flow meter on reagent delivery with its control valve, differential pressure across the catalyst layers for the fouling trend, and the gas analyzer house kept honest by the same audit trail, with a centrifugal fan on the sample line where extractive systems need it. The plc runs the reagent against the NOx signal with feed forward from load and trim from the analyzers, and the historian's trend of NOx, slip, dp, and reagent per ton is the operating story the catalyst manager reads quarterly.

The analyzers deserve a paragraph of procurement attention because the whole control story stands on them. NOx measurement before and after the reactor, chemiluminescence or extractive ultraviolet by the permit's method, sets the removal the system steers by; the ammonia slip measurement, extractive fourier transform or tunable diode laser across the duct, is the harder instrument and the one the tightest permits run continuous; and calibration gas discipline, certified bottles on a schedule the auditor checks, is what keeps both defensible. Plants that cheap the analyzers get to discover their slip at stack test, in front of the regulator, with the tuning crew booked three weeks out; the instrument budget is the cheapest compliance on the project.

Chapter 5 / 06

Selection Decision Factors and RFQ Language

Selection starts with the flue gas, characterized honestly. Flow and temperature across the load range place the reactor and size the window; the NOx inlet, from the combustion source as it actually runs, fixes the reagent demand; the dust and its chemistry pick the pitch and the poisoning forecast; and the sulfur side fixes the bisulfate arithmetic. A gas analysis package with the bid, NOx basis stated as NO2 equivalent, dust and its composition, SO2 and SO3 if available, arsenic and calcium on coal, alkali on biomass, is the difference between vendors quoting the same reactor and vendors quoting their assumptions.

The reagent decision follows the site's safety logistics. Anhydrous where regulation and siting permit, for the lowest reagent cost and the smallest storage; aqueous as the market middle, safer and heavier to haul, standard on hrsg duty; urea where the site refuses ammonia hazards or the delivery logistics favor it, paying the hydrolyzer or the injection hardware. The reagent plant, storage, unloading, vaporization or hydrolysis, injection air, is a package of its own within the project, and its scope boundary with the reactor supply is a contract line to draw deliberately.

The control philosophy deserves selection attention because the machine is a loop, not a box. Feed forward from boiler load or gas turbine output with feedback trim from outlet NOx is the standard architecture; the slip constraint is handled by stoichiometry limits and, on the tightest permits, by an ammonia analyzer in the loop; and the tuning of the AIG zones, the commissioning mapping and rebalancing, is what converts the designed uniformity into achieved slip. Ask bidders for their tuning procedure and acceptance basis, because the difference between 2 and 5 ppm slip at the stack is mostly grid tuning discipline.

A complete RFQ states, on one process data page: flue gas flow, temperature range, and pressure; inlet NOx with basis and required outlet with averaging period; ammonia slip limit and fly ash ammonia limit if ash is sold; dust loading and chemistry with poison inventory; sulfur species; available duct space and pressure drop allowance; reagent preference or openness with storage constraints; catalyst type and pitch expectations; layers initial and spare; the tuning deliverable with uniformity acceptance; catalyst life guarantee with activity test protocol and replacement pricing; and the interface boundary, reactor shell, hrsg coordination, ash handling. Vendors quoting against that page quote the same system, and their volumes, pitches, slips, and layer schedules become comparable line items.

Integration with the rest of the flue gas train belongs in the same decision. Upstream, the burner and furnace setting set the NOx the reactor receives, and combustion tuning ahead of SCR is always cheaper than catalyst; downstream, the particulate collector and the wet or dry scrubber share the duct, the ash streams interact with the ammonia, and on retrofits the fan's capacity for the added pressure drop, the steel's room for the reactor, and the outage window for the tie in are the project's hard edges. An SCR bought without the train is a reactor with promises. The reagent day tank gets a level transmitter with delivery alarms, the duct ahead of the reactor gets a pressure transmitter so the fan and the dp trends read against something absolute, and the reheat train gets a temperature controller of its own so tempering never surprises the catalyst.

Chapter 6 / 06

Installation, Standards, Failure Modes, and Maintenance

Installation is duct and structural work with a catalyst handling discipline: the reactor shell erected and sealed, the catalyst modules lifted and set in their layers with the sealing system that stops gas bypassing around them, the reagent plant piped and proved, and the analyzers calibrated on certified gases before first injection. Commissioning tunes the AIG against real flue gas, maps NOx and ammonia across the duct, balances the zones to uniformity, and establishes the baseline activity and pressure drop that every operating year is measured against. The performance test, outlet NOx and slip at agreed loads to the permit's method, closes the purchase.

The governing references are the environmental practice and the machinery standards around it: the EPA's SCR fact sheet and the agency's monitoring guidance define the control technique's monitoring expectations, vendors such as Mitsubishi Power and GE Vernova document the applied system practice on power duty, and the boiler and hrsg codes govern the reactor's pressure parts where it owns any. There is no single international SCR product standard, and the protections are the performance guarantee with its test code, the catalyst activity protocol with its independent laboratory, and the layer life commercial terms.

Failure modes are chemical and mechanical with dust as the accelerant. Performance decay toward the slip limit is catalyst deactivation, poisoning and blinding by the fuel's species, answered by the layer management plan, adding the spare layer or replacing the front one, from the activity test's evidence. Rising pressure drop is fouling and plugging, ash building in the catalyst cells, answered by soot blowing and, on upsets, by washing at the turnaround, never hot. Maldistribution shows as one duct corner's slip rising while another's NOx lags, answered by AIG zone rebalancing. Ammonia odor or the ash sales rejection slip is the bisulfate or adsorption story moving downstream, answered by stoichiometry discipline. And the reagent plant's own failures, vaporizer fouling, hydrolyzer upsets, injection nozzle plugging, announce themselves in the reagent flow and the uniformity trend.

SymptomLikely causeFirst action
Outlet NOx rising, reagent at limitCatalyst deactivation or maldistributionRun activity test on layer samples; check AIG balance; plan layer addition
Ammonia slip rising at same NOxStoichiometry drift or grid imbalanceRebalance AIG zones; verify analyzers; review control tuning
Pressure drop across reactor climbingAsh plugging of cellsIncrease blowing frequency; inspect at outage; verify pitch against actual ash
Ash ammonia content rejectionSlip adsorption on fly ashTighten stoichiometry; confirm ash monitoring basis; tune grid
Reagent flow unstableVaporizer or hydrolyzer, nozzle pluggingService reagent train; strainer and nozzle inspection

Routine maintenance is a schedule of small disciplines: soot blowing per the ash's demand, analyzers calibrated with certified gas on a calendar the permit audits, reagent plant service on its pumps and vaporizers, catalyst samples pulled and tested at the intervals the activity protocol sets, and the dp and slip trends reviewed quarterly against the layer plan. The catalyst handling at layer work, module crane access, sealing system renewal, spent module disposal or regeneration, is planned from the day the reactor is drawn, because the access that was cheap at design time is priceless at the first layer change.

The institutional item is the layer plan's honesty. Catalyst life is a fuel story and a slip story, and the plan that says six years on an ash that says three is a stack test surprise waiting; the activity test regime, samples tested by an independent laboratory on schedule, converts the decay from anecdote to curve, and the curve buys layers at the right year, budgets them in the right outage, and keeps the permit's two numbers, NOx and slip, comfortably apart.

Catalyst regeneration deserves its line in the maintenance economics because it changes the layer plan's arithmetic. Spent modules can be washed and reactivated by specialist services, restoring most of the original activity at a fraction of new catalyst cost, or chopped and the titanium tungsten vanadium materials recovered; both routes exist in a commercial market, and the disposal plan that names them, with the ash and the poison inventory the fuel brought, belongs beside the replacement pricing in the contract. The layer plan that treats every end of life as new purchase leaves a third of the lifecycle money on the table, and the vendors who quote both options are telling the buyer they expect to keep the business for twenty years.

FAQ

How does SCR differ from a catalytic or thermal oxidizer?

By chemistry and pollutant. SCR reduces nitrogen oxides to nitrogen using ammonia over a catalyst; oxidizers destroy VOCs and HAPs by oxidation at high temperature. The acronyms overlap in the word catalytic, the machines share nothing but flue gas, and plants with both duties run both systems, sometimes in series in the same duct train.

What ammonia slip should I expect and why does it matter?

Modern permits hold 2 to 5 ppm at the stack, often the sizing constraint rather than NOx itself. Slip matters beyond the number: ammonia salts with sulfur as ammonium bisulfate fouling the air heater, adsorbs into fly ash and can end its sale to cement, and announces itself to neighbors as odor. The guarantee should state slip at end of catalyst layer life.

Anhydrous ammonia, aqueous, or urea, which reagent?

A safety and logistics decision: anhydrous is cheapest per ton removed and most regulated to store, demanding dispersion analysis and siting; aqueous at 19 to 29 percent removes most of the hazard for a heavier delivery; urea is benign to handle and pays for a hydrolyzer or injection hardware to make ammonia on site. Regulation is moving the default toward urea on many sites.

Where in the flue gas train does the reactor go?

Where the temperature window, roughly 300 to 420 deg C, and the dust tolerance intersect: high dust before the particulate collector keeps temperature free and pays in fouling, low dust after it pays reheat fuel for a cleaner life, tail end after the scrubber is cleanest and most reheated, and the gas turbine hrsg embeds the reactor mid bank where exhaust temperature lands in the window.

How is catalyst volume actually determined?

From area velocity, flue gas flow over the catalyst's geometric surface, crossed with the required conversion, the slip limit, and the activity the catalyst retains at end of life; dust and poisons in the gas set the pitch, pitch sets how much surface fits per volume, and layers initial plus spare set the margin. The activity test protocol is what keeps the vendor's activity claims honest across the years.

Why does my SCR need an ammonia injection grid tune?

Because the reagent must arrive at the catalyst face uniform to a few percent, and no duct hands you that for free: the grid's zones are balanced against a cross duct map of NOx and ammonia at commissioning, then rebalanced as the catalyst ages unevenly. The difference between meeting 2 ppm slip and living at 5 is mostly tuning discipline, which is why the procedure and its acceptance basis belong in the purchase.

How does SCR compare with SNCR?

Same ammonia chemistry, no catalyst: SNCR injects into the furnace's hot zone and achieves 20 to 50 percent removal with minimal hardware, SCR's catalyst delivers 70 to 95. Modest targets suit SNCR alone, deep permits demand SCR, and some plants run SNCR trimming the inlet NOx ahead of a smaller SCR, trading reagent against catalyst volume.

Sources

  1. US EPA - Air Pollution Control Technology Fact Sheet: Selective Catalytic Reduction (EPA-452/F-03-032, PDF)
  2. Mitsubishi Power Americas - SCR system
  3. Mitsubishi Power - Selective catalytic reduction (flue gas denitration)
  4. GE Vernova - Selective catalytic reduction for power and industry
Ask SpecForge AI