A sequencing batch reactor, SBR, is a fill and draw activated sludge system in which all the steps of biological wastewater treatment, equalization, biological reaction, settling, and clarified effluent withdrawal, happen as timed phases in the same tank: the basin fills, aeration and mixing react for the designed period, aeration stops and the solids settle, and a decanter draws treated effluent off the top before the cycle repeats. Multiple basins in staggered phase give continuous treatment of a continuous inflow, and the timing of the phases, not fixed hardware, defines the process: the same tank runs carbon removal, nitrification, denitrification, and biological phosphorus removal by changing what happens when. The US EPA's sequencing batch reactor fact sheet is this page's formal reference, and this page treats the SBR basins, decanters, aeration, and controls as the purchasing object.
This page is written for the engineer specifying an SBR for a municipal works, an industrial biological plant, or a package treatment station. It works through what the system does and what is being bought, how the cycle phases do the work, which basin and decanter configurations fit which duties, the parameters that appear on design sheets, and the selection factors and RFQ language that decide whether the installed works meets its effluent permits cycle after cycle.
The decision concentrates in five places: the load and its diurnal profile, the effluent permit including nutrients, the cycle and phase times that deliver it, the decanter and its scum and solids protection, and the aeration, mixing, and control system that runs the choreography. Get those right and basin count, volume, and equipment sizes follow.
Chapter 1 / 06
What a Sequencing Batch Reactor Is and What Is Being Decided
The machine this page describes is a set of treatment basins and their phase machinery. Each basin is a concrete or steel tank with a fine bubble diffuser grid on the floor, mixers that keep solids suspended without aerating, a decanter, a moving weir or floating trough that lowers into the clarified supernatant to draw effluent, a sludge wasting arrangement, and instruments, dissolved oxygen, mixed liquor, and level, reporting to the controller that runs the phases. Feed arrives from the headworks through screening by the bar screen family and grit removal; aeration comes from blowers, regenerative or roots lobe classes; and the controller sequences every basin through its cycle with phase times set by the design and trimmed by the instrumentation.
What is being decided when an SBR is purchased is an effluent guarantee delivered by a schedule rather than a fixed train. The buyer is purchasing a stated permit, BOD, TSS, ammonia, total nitrogen, and phosphorus where required, at a stated load and diurnal profile, with basin volumes, decanter sizing, blower capacity, and control logic as the delivery mechanism, and with the flexibility to re-tune the same hardware as the permit tightens or the load grows. Everything on the design sheet, basin count and volume, cycle time, phase splits, decanter rate, sludge age, exists to support those guarantees, and the honest designer sizes from load data and temperature, not from a per capita table alone.
The SBR sits in the biological treatment family with defined neighbors. It is not a membrane bioreactor, which holds solids behind a membrane instead of settling them and runs at much higher mixed liquor; it is not a moving bed biofilm reactor, which grows its biology on carrier media in a continuous tank and still needs a downstream clarification step; and it is not a conventional continuous flow activated sludge plant with separate aeration basin and clarifier, which the SBR replaces by putting both functions in one tank on a timer. Compared with those neighbors, the SBR's identity is the decanter and the clock: biological selector behavior, settling, and effluent withdrawal all happen in sequence in one basin.
Different buyers buy the same system for different reasons. Small municipalities buy two basin SBRs for operator simplicity and capital economy against a continuous plant. Growing towns buy SBRs for the permit flexibility, tightening nutrient limits met by re-timing cycles rather than building tanks. Industrial plants buy SBRs for batch compatible production schedules and variable loads, dairies and food processors running their works in campaign mode. Resorts and camps buy package SBRs for seasonal turndown. All of them buy the same physics: one tank, timed phases, and a decanter.
The economics deserve their own paragraph because the SBR trades hardware for choreography. Against a continuous plant of equal capacity, the SBR saves the separate clarifier and its return sludge pumping, spending the savings on decanters, larger basin equalization, more control logic, and intermittent blower operation; energy management follows the aeration demand profile, and the equalization built into the cycle buffers diurnal peaks that would size a continuous plant's aeration peak. The honest comparison prices the whole works, headworks to disinfection, at the site's load and temperature, and the SBR usually wins below mid scale and loses above it, which is a fact about load, not about fashion.
A short tour of named duties makes the system concrete. At a 15,000 person town, two SBR basins run four hour cycles in stagger, filling and reacting while the partner settles and decants, meeting 10 ppm BOD and 1 ppm ammonia. At a dairy, a single basin runs an eight hour campaign cycle against the production day, denitrifying in the mixed fill and nitrifying in the aerated react. At a mountain resort, a package SBR turndowns to winter load with fewer cycles and colder kinetics designed in. Each duty names the same knobs, cycle time, phase splits, decanter depth, and sludge age, with numbers that differ while the basin barely changes.
Chapter 2 / 06
How the Cycle Phases Do the Work
The canonical cycle has five phases, and their durations are the process design. Fill brings raw or pretreated wastewater into the basin, with the option of a mixed, unaerated fill that starts denitrification and biological phosphorus release by mixing the influent with the settled biomass; React aerates the mixed liquor, driving carbon oxidation and nitrification, the conversion of ammonia to nitrate; Settle stops aeration and mixing and lets the biomass settle as a blanket, leaving a clarified supernatant above it; Decant lowers the weir and draws effluent at a controlled rate without disturbing the blanket; Idle waits for the basin's next slot, sometimes holding a mixed condition for selector behavior. Idle is optional bookkeeping; the other four are the process.
Nutrient removal lives in the sequencing, which is the SBR's signature advantage. Nitrification needs aerated time and sludge age; denitrification needs anoxic time with carbon available, and the mixed fill phase delivers exactly that by contacting influent carbon with the nitrate left from the previous cycle; biological phosphorus removal alternates anaerobic and aerobic exposure, and the cycle phases provide the alternation without additional vessels. Total nitrogen limits are met by sizing the mixed fill against the aerated react; phosphorus, where the biological route is chosen, by the anaerobic phase and the wasting discipline, with chemical polishing by coagulant dosing where the permit demands.
The decanter is the machine's precision instrument. During settle, a clear zone forms above the blanket, and the decanter, a floating or traveling weir with a closure to exclude scum and solids at the start of draw, lowers into that zone and withdraws effluent at a rate that does not pull the blanket up; its draw depth sets the working volume exchanged per cycle, and its scum exclusion and solids protection, weirs with baffle gates that close during fill and react, decide whether effluent TSS meets permit on a windy day. Decanter vendors publish draw rate and travel, and the design pairs them with the basin geometry so the blanket's top never meets the weir's bottom in worst case settling.
Aeration and mixing are the energy budget and the mass transfer machine. Fine bubble diffusers on floor grids, fed by blowers, regenerative blower classes at smaller works and roots lobe blowers at larger ones, deliver oxygen against the mixed liquor's demand, controlled by dissolved oxygen instrumentation to avoid over aeration in the react phase; mixers run during mixed fill and anoxic phases, keeping solids in suspension without adding air. Intermittent blower operation across basins is the SBR's energy character, and blower sizing, with variable frequency drives where the profile rewards them, follows the cycle's oxygen demand integrated over the day, not a single peak number copied from a continuous plant sheet.
Sludge inventory is managed by wasting on a schedule rather than by a continuous return stream, because there is no separate clarifier to return from. The mixed liquor concentration and the sludge age are process variables the operator sets by wasting solids from the basin, at the end of settle from the blanket or during mixed phases from the mixed liquor, sending them to thickening and dewatering, a screw press or the site's sludge train, often with anaerobic digestion ahead of it at larger works. The SBR's selector behavior, its resistance to filamentous bulking, comes from the fill regime's high substrate gradient, and it is one reason settling in an SBR is often better than the continuous plant's at the same sludge age.
Control and instrumentation run the choreography and prove the effluent. The controller sequences basins through phases with per phase timers and interlocks, level instruments confirm fill volumes, dissolved oxygen instrumentation trims aeration, and effluent flow metering plus sampling prove the permit. The flexibility that makes an SBR powerful is all in the controller: retiming phases for winter kinetics, nutrient permit changes, or load growth is a settings change, not a construction project, and the purchase should specify a controller that exposes the phase logic to the operator rather than burying it in a vendor black box.
Chapter 3 / 06
Basin Configurations, Variants, and Duty Boundaries
Configuration choice begins with basin count and cycling against the flow. Two basins in staggered phase treat continuous inflow and give maintenance redundancy; three or more basins smooth the load and ease peak weather cycles; single basin works run where inflow can be pumped to schedule, the classic industrial campaign pattern. Continuous feed variants admit inflow during react and even settle in a separate baffle zone, trading the pure batch selector behavior against hydraulic simplicity at higher flows. The decanter count and geometry follow the basin plan, and the equalization volume inside the cycle, the exchange volume per cycle, sets how much diurnal buffering the works gets for free.
Configuration
Typical duty
Character
Two basin stagger
small municipal
The standard works
Three basin rotation
mid works, wet weather
Peaking and maintenance room
Single basin, scheduled feed
industrial batch plants
Campaign compatible
Continuous feed SBR
larger flows
Hydraulic simplicity trade
Package SBR
resorts, camps, stations
Factory built, turndown designed
Duty boundaries keep the selection honest. The SBR is a biological works: heavy metals and toxic shocks are biology problems to be managed by pretreatment and equalization, not absorbed. Very large continuous flows, the big city scale, favor continuous plants whose clarifiers and return streams scale more gracefully than decanter arrays. Where land is nearly absent and reuse quality is demanded, the membrane bioreactor's footprint and effluent win despite its energy; where a plant must bolt onto an existing continuous works, the moving bed biofilm reactor adds capacity in existing tanks. Within its band, the SBR is the most flexible permit machine in the family.
Where it sits in the works matters as much as the basin. Upstream, the headworks, screens of the bar screen family and grit removal, protect diffusers and decanters from rags and sand, and flow equalization before the SBR smooths what the cycle cannot; pumping stations with sewage pump classes deliver the inflow head. Downstream, effluent disinfection by uv sterilizer or an electrochlorinator's chlorine, filtration where reuse demands, and the sludge train, thickening then a screw press or other dewatering, with anaerobic digestion at larger works, complete the plant. The SBR is bought as the works' biological heart, and its interfaces to headworks, disinfection, and sludge are the battery limit the RFQ draws.
Package and constructed works share the design. Factory built package SBRs, steel or fiberglass basins with decanters, blowers, and controls mounted, serve flows to a few hundred cubic meters per day and install in weeks; constructed concrete basins serve the larger municipal range with the same equipment families at larger sizes. The choice between them is civil versus manufactured cost at the site's scale and conditions, and both run the same cycle physics, which is why the specification's process numbers, load, cycle, and effluent, dominate the equipment list.
The works around the basins supplies half the biology's success, so the neighbors deserve a fuller paragraph. Influent arrives from the headworks, where a bar screen and grit removal protect the diffusers and decanters, and where the wet well's sewage pump station sets the flow pattern the cycles must absorb; on works with odor control, the headworks air passes through an activated carbon filter stage before it reaches the neighborhood. Inside the basin, the mixers are agitator class machines selected for suspension at the design mixed liquor without entraining air, and the decanter is served by its own maintenance access because it is the only precision machine in the tank. Effluent leaving the decanters is metered with a flow meter for the permit account and disinfected downstream. A designer who treats these neighbors as part of the sequencing batch reactor purchase buys a works; one who buys basins alone buys a clarifier with a clock.
Chapter 4 / 06
Key Specification Parameters
The design sheet parameters fall into four groups: load and effluent, cycle, equipment, and energy. Load parameters are design BOD and TSS load, ammonia and nutrient load where permitted, flow average and peak with the diurnal profile, and design temperature. Cycle parameters are basin count and volume, exchange volume per cycle, cycle time and phase splits, sludge age and mixed liquor target, and settling time against the decanter draw. Equipment parameters are decanter draw rate and travel, diffuser grid and blower capacity, mixer sizing, and wasting arrangement. Energy parameters are aeration demand integrated over the cycle and blower power at design and average. A design sheet that quotes an effluent without the load profile and temperature behind it is not comparable to one that states them.
Parameter
Typical range
Design note
Cycle time
3-8 h
Shorter carbon only, longer nutrients
Basins
1-4 typical
Stagger gives continuity
Exchange volume
20-35% of basin
Equalization inside the cycle
MLSS
3000-6000 mg/L
Settling time pairs with it
Sludge age
10-30 d
Nitrification sets the floor
Decanter draw rate
per vendor curve
Blanket safety margin
Settle phase
45-90 min
Worst case sludge governs
Aeration control
DO trimmed
Energy and nitrogen both
Effluent BOD/TSS
10-30 / 10-30 mg/L
Permit driven
Cycle and phase times deserve explicit numbers in every specification because they are the process. The designer should state the cycle time at design load and temperature, the phase split, mixed fill, aerated fill, react, settle, decant, the exchange volume per cycle against the diurnal inflow, and the worst case settling check, the sludge volume index times mixed liquor against the decanter's draw depth, with margin. Nutrient permits add the anoxic and anaerobic phase sizing against the nitrogen and phosphorus loads. These numbers, not the equipment list, are what the works was actually bought to deliver.
Decanter and aeration equipment round out the sheet. The decanter's draw rate and travel, its scum exclusion and closure arrangement, and its solids protection at the start of draw decide effluent TSS on bad days, and vendors publish curves the designer pairs with basin geometry. Diffuser grids quote standard oxygen transfer efficiency at the works' diffuser depth, blowers quote capacity against the cycle's peak demand with turndown, and mixers quote suspension at the design mixed liquor. Instruments, dissolved oxygen, level, effluent flow, and the sampling provisions for permit proof, are the process's witnesses and belong in the controls scope explicitly.
Instrumentation deserves its own rows on the design sheet because the cycle is only as good as its measurements. The dissolved oxygen probe controls aeration, the level instruments confirm fill volumes and decant draw, the effluent flow meter closes the permit account, and a ph meter on the basin tracks the biology's acid production, the early warning on toxicity and nitrification trouble that no timer can see. Sampling provisions, a composite sampler on the effluent and grab points per phase, turn the daily permit proof into a routine instead of an excavation. The controller should expose its phase logic, timers, and setpoints to the operator, and log the data, because the cycle's flexibility is worthless if retuning for winter or for a new permit requires a vendor visit. Works that measure themselves retune in an afternoon; works that do not explain themselves to the regulator.
Chapter 5 / 06
Selection Decision Factors and RFQ Language
Selection starts from the load and the permit, written as numbers and profiles. The designer writes the flow, average, peak, and diurnal shape; the load, BOD, TSS, ammonia, total nitrogen, phosphorus; the design temperature range including the cold season that governs nitrification kinetics; and the permit the works must meet, current and known future. From that basis, basin count, cycle time, and phase splits follow with little freedom, and the decanter and blower sizes follow from them. An RFQ with annual averages invites a design that fails the cold February permit night.
Duty driver
Favored configuration
Watch item
Carbon permit only
short cycle, 2 basins
Peaking and buffer volume
Ammonia permit
longer aerated react
Cold season sludge age
Total nitrogen permit
mixed fill denitrification
Anoxic phase vs cycle length
Phosphorus permit
anaerobic phase plus polish
Bio P stability, coagulant trim
Industrial batch loads
single basin scheduled
Toxic shock pretreatment
Decanter selection is the second decision and it is made with the basin, not from a catalog. Draw rate against blanket rise, travel against the exchange volume, scum exclusion against the works' scum load, and closure discipline during non decant phases decide whether effluent TSS holds permit in worst case settling, and the vendor's references on similar sludge are worth more than the brochure curve. The designer should demand the decanter's draw curve and the basin's settling margin check together, because a decanter that outruns the blanket is the difference between a permit and a violation notice.
The RFQ language that returns comparable offers states the load and the process demanded. State flow and load with diurnal and seasonal profiles, the permit now and known future, design temperatures, the cycle strategy expected with phase splits, decanter requirements with solids protection, blower and aeration control basis, control system openness including operator access to phase logic, headworks and sludge interfaces, and the performance test basis over a stated period including the cold season if possible. A complete RFQ paragraph reads: design 4500 cubic meters per day average, 9000 peak, BOD 300 milligrams per liter influent, permit 10 BOD, 15 TSS, 1.0 ammonia winter, two basin SBR with four hour cycles, decanter with scum closure, DO controlled aeration, phase logic accessible to operators, performance tested over 90 days including minimum temperature month.
Commercial comparison is only fair on a normalized basis. Offers should be forced onto one table: basin count and volumes, cycle and phase splits, decanter draw and protection, blower capacity and control, energy at average and design, controls scope and openness, sludge wasting provision, references on the same sludge and climate, delivery, and the civil versus package boundary. The cheapest works is very often the one with the least basin volume per kilogram of BOD and the smallest decanter margin, and its operating cost lands in permit excursions and operator overtime; the table that prices a cold season of compliance is the one that tells the truth.
Chapter 6 / 06
Installation, Standards, Failure Modes, and Maintenance
Installation is a civil works with equipment fit out. Basins build or set, diffuser grids and decanter rails install, blowers and mixers mount with their piping, and the control system wires its instruments and actuators. Commissioning seeds and grows the biomass, then tunes the cycle: phase timers to the load, aeration to the dissolved oxygen setpoint, decanter travel to the basin's exchange, and wasting to the target sludge age, over weeks of sampling until the effluent proves the permit. The commissioning record, the cycle settings and the effluent data that justified them, is the works' baseline for every seasonal retune that follows.
Failure modes have a known hierarchy. Decanter faults lead the permit risks, a weir that starts its draw into the blanket or drags scum, and their causes are mechanical travel and closure problems or settling failures upstream in the cycle; bulking and foaming sludge, from nutrient imbalance, low substrate gradients in mis set fills, or industrial shocks, ruins settle and forces decant curtailment; diffuser fouling lifts aeration pressure and starves oxygen; blower wear loses capacity against the demand; and control failures, a stuck valve, a false level, freeze the choreography mid cycle. On the process side, toxic shocks from industrial slug loads kill biology that nothing mechanical can save, which is why pretreatment agreements and equalization are process equipment too.
Symptom
Likely cause
First response
Effluent TSS spikes
decanter into blanket
Travel and settle audit, scum check
Poor settling, rising foam
bulking filamentous
Fill regime audit, wasting retune
Ammonia breaking through
cold or sludge age short
Cycle retune, waste less, audit load
Aeration pressure rising
diffuser fouling
Grid inspection, cleaning cycle
Basin stuck mid phase
valve or instrument fault
Manual override, interlock service
Maintenance is planned around decanters, diffusers, and blowers. Decanter tracks, drives, and closure elements serviced on schedule, diffuser grids inspected and cleaned at drain downs, blower filters and oil per interval with vibration trending, mixer drives serviced, and instruments, dissolved oxygen probes especially, cleaned and calibrated on a monthly discipline because the whole aeration control rests on them. Sludge handling, wasting pumps and the downstream thickening and dewatering chain, runs its own program. Spares hold decanter wear parts, diffuser spares, blower service kits, and a dissolved oxygen probe.
Operational stewardship is what the purchase actually bought. Operators who sample the cycle, influent, mixed liquor at each phase, settled blanket depth, and effluent, and who retune the timers seasonally, run SBR works to their permits for decades; operators who leave the commissioning settings untouched meet the cold season unprepared and the permit sampler unannounced. The works' trend board, cycle settings, sludge age, blanket depth, effluent numbers, is the process's real contract, and reading it weekly through the seasons is the difference between a flexible permit machine and a blamed tank.
Commercial comparison earns a closing paragraph because quotations vary more in scope than in steel. Offers should be forced onto one table: basin count and volume, cycle and phase splits with the settling margin check, decanter draw rate and protection, blower capacity and control, mixer sizing, the control system's openness, the headworks and sludge interfaces, energy at average and design, and references on the same sludge and climate. The cheapest works is very often the one with the least basin volume per kilogram of BOD and the smallest decanter margin, and its operating cost lands in permit excursions and operator overtime. The table that prices a cold season of compliance, a decade of energy, and the sampling that proves both is the table that tells the truth, and the RFQ that demands it has already done half the engineering.
FAQ
What are the phases of an SBR cycle?
The canonical five are fill, react, settle, decant, and idle. Fill admits wastewater, optionally mixed and unaerated to start denitrification and biological phosphorus release; react aerates for carbon oxidation and nitrification; settle stops aeration and mixing so the biomass forms a blanket under a clarified supernatant; decant lowers the weir and draws treated effluent; idle briefly waits for the basin's next slot. Phase durations are the process design, retimed as load, temperature, and permit change.
How does an SBR remove nitrogen?
By sequencing aerobic and anoxic conditions inside the same basin: the aerated react phase nitrifies, converting ammonia to nitrate, and the mixed, unaerated fill phase of the next cycle contacts that nitrate with influent carbon, denitrifying it to nitrogen gas. The split between mixed fill and aerated react is the total nitrogen lever, tuned against the cycle length. Where permits demand very low nitrogen, additional anoxic time or step feed patterns extend the same logic without new vessels.
What does the decanter do, and why does it matter so much?
The decanter is the moving weir that draws clarified effluent from above the settled blanket at a controlled rate, closing during fill and react so scum and mixed liquor never pass through it. It matters because it is the effluent's last gate: a decanter that starts into the blanket or drags scum writes TSS permit violations no amount of good biology can offset. Its draw rate, travel, scum exclusion, and closure discipline are specified against worst case settling with margin.
How is an SBR different from a conventional activated sludge plant?
The conventional plant separates functions in space, an aeration basin flowing continuously to a clarifier with return sludge pumping; the SBR separates them in time, one basin cycling through aeration, settling, and decant on a schedule. That saves the clarifier and return pumping, builds equalization into every cycle, gives selector resistance to bulking, and leaves the process tunable in software. Continuous plants scale more gracefully at very large flows; SBRs dominate small and mid works and industrial batch duty.
Can an SBR meet phosphorus limits?
Biological phosphorus removal works in an SBR by alternating anaerobic and aerobic phases, which the cycle provides without extra vessels, and the wasting discipline carries the accumulated phosphorus out of the system. Where permits are tight, coagulant dosing, iron or aluminum salts, polishes the residual, often at the decanter or in a small contact step. The biological route's stability depends on sludge age and carbon profile, and the RFQ should state which route, or which blend, the works is being bought to deliver.
What happens to an SBR in cold weather?
Biological kinetics slow, most critically nitrification, so winter demands longer aerated phases, higher sludge age, or both, and the cycle strategy must be retuned before the cold season rather than after the first violation. Design covers this with temperature as an explicit basis and margin in basin volume and blower capacity. The works that retunes seasonally meets January the same way it met July; the works that never retunes meets the sampler instead.
How much equalization does an SBR provide?
Every basin buffers inflow by design: the exchange volume drawn per cycle, commonly a fifth to a third of basin volume, is storage the continuous plant must build separately, and staggered basins extend the buffer across the diurnal curve. Wet weather peaks still need headroom, more basins, deeper exchange margin, or upstream equalization, and the design's peaking check belongs in the data sheet. The SBR's free equalization is one of its quiet economic advantages.