LNG Vaporizer

An LNG vaporizer is a purpose built heat exchanger that takes liquefied natural gas at about minus 162 degrees C from storage and delivers it as pipeline specification gas at the required send out pressure and temperature, using one of four main heat sources: ambient air drawn across extended surface tubes, a heated water bath, an intermediate fluid loop warmed by combustion or process heat, or direct submerged combustion inside a water bath. Chart Industries catalogs vaporizers across these families for LNG terminals and satellite stations, and the choice among them is an exercise in matching heat source economics, site ambient, and emissions to the send out profile. This page treats the vaporizer and its utilities as the purchasing object.

This page is written for the engineer specifying LNG vaporization for an import terminal, a peak shaving plant, or an industrial satellite station. It works through what the machine does and what is being bought, how each heat source shapes the design and its derate, which configurations fit which duties and sites, the parameters that appear on vendor data sheets, and the selection factors and RFQ language that decide whether the installed train meets its send out across the seasons.

Compact finned heat exchange surface of the class used in ambient air LNG vaporizers, shown as an installed unit

Photo: Renegade, Public domain, via Wikimedia Commons

The decision concentrates in five places: the send out profile, rate, pressure, temperature, and turndown; the site ambient, the temperature and humidity statistics that govern air vaporizer frosting and water bath heating demand; the utility context, air, water, and fuel availability priced honestly; the emissions envelope for combustion based types; and the reliability architecture, how many trains and which backup. Get those right and the heat source choice, tube surface, and utility sizes follow.

Chapter 1 / 06

What an LNG Vaporizer Is and What Is Being Decided

The machine this page describes is the regasification heat exchanger train. LNG leaves storage as a subcooled liquid near minus 162 degrees C, is pumped to above send out pressure by high pressure LNG pumps, and then vaporizes and superheats through the vaporizer to a typical send out specification, commonly between 0 and 15 degrees C at the battery limit, with the exact number set by the pipeline or downstream contract. The temperature lift is enormous, roughly 170 degrees C plus superheat, so the vaporizer is among the largest heat duties on the site, and its heat source defines the plant type: air heating, water heating, or fuel heating, each with its own operating cost and emissions signature.

What is being decided when an LNG vaporizer is purchased is a send out guarantee across the ambient envelope plus a utility and emissions statement. The buyer is purchasing a stated gas rate at stated pressure and temperature at the design ambient, with a defined derate or supplementary heat strategy down to the extreme ambient, with stated fuel or power or water consumption, and for combustion types, emissions within the permit. Everything on the vendor data sheet, heat transfer surface, bath power or burner duty, fan power, materials, and the ambient basis, exists to support those guarantees, and the honest vendor states the derate curve rather than a single point.

The LNG vaporizer sits in the cryogenic heat exchanger family with defined neighbors. It is not an air-cooled heat exchanger or air-cooled condenser, which reject process heat to ambient air at warm service temperatures; the LNG vaporizer harvests heat from ambient air or water at a temperature far below ambient, and the physics of frost govern its surface design. It is not a shell and tube heat exchanger in the general process sense, though water bath types contain tube bundles. It is not a plate-fin heat exchanger core of the vacuum brazed aluminum class, though ambient air units use extended aluminum or stainless surfaces. The neighbor pages cover those warm duties; this page covers the cryogenic regasification machine.

Different buyers buy the same machine for different reasons. A large import terminal buys a bank of ambient air vaporizers plus submerged combustion units for peak and backup, minimizing continuous fuel burn and emissions. A peak shaving plant buys water bath or SCV capacity that starts fast and runs hard for the few coldest days. An industrial satellite station, a glass plant or a remote power station switching to gas, buys a compact ambient air vaporizer sized to its boiler or burner demand with electric or small fuel trim. A marine bunkering or fuel gas handling system buys intermediate fluid vaporizers that reuse engine heat. The specification language differs, but the heat balance is shared.

The economics deserve their own paragraph because the heat source is the operating cost. Ambient air is free but capacity limited by frost; water is cheap where warm seawater or waste heat exists but carries intake and discharge environmental review; fuel fired submerged combustion burns roughly 1.5 to 2 percent of the send out gas and emits combustion products, a cost line and a permit line at once; electric heating is clean and simple but sized by the power bill and grid connection. The honest comparison prices the annual heat duty mix, base plus peak, against the utility tariffs and permits, and terminals that run SCVs as base load are terminals whose energy arithmetic was never done.

A short tour of named duties makes the machine concrete. At a coastal import terminal, four ambient air vaporizer trains rate the base load with two submerged combustion vaporizers in standby, the SCVs lighting on the coldest mornings when frost derates the air units. At a mountain peak shaver, a single water bath unit with a burner package vaporizes tank inventory into the city gate at ten times the storage withdrawal rate. At a satellite station feeding an industrial boiler, an ambient air vaporizer with an electric water trim covers the winter demand swing. Each duty names the same knobs, heat source, surface, derate, and turndown, with numbers that scale while the cryogenic tube barely changes.

Chapter 2 / 06

How the Heat Sources Do the Work

Ambient air vaporizers run LNG through long serpentines of extended surface tube, star fin or extruded fin aluminum in most designs, stacked in tall frames with fans optional and natural draft common. Heat flows from air to tube against a huge temperature difference, and the air side drops below freezing, so atmospheric moisture deposits as frost on the fins. Frost is the governing physics: it insulates the surface, choking airflow and heat transfer, so capacity falls over hours of operation; plants counter with multiple banks operated in rotation, defrosting one bank while others run, and accept the derate curve as ambient temperature and humidity fall. Design is therefore a surface area and cycling exercise, not a single point rating.

Water bath vaporizers immerse the LNG tube bundle in a heated water bath, with heat from combustion firing a burner through an immersion tube, from steam or hot water, or from electric elements. The bath holds a stable temperature commonly near 40 to 60 degrees C, the bundle sees a gentle, constant driving force, and frosting of the air side disappears entirely; the costs are the water treatment and heat loss of an open warm bath, the fuel or power to hold it, and for fired types the flue gas stream. Chart's Thermax indirect fired water bath units are representative of the class, and the same bath architecture with a different heat source serves steam and electric variants.

Intermediate fluid vaporizers close the loop with a heat transfer fluid, water glycol or a formulated fluid, warmed by a fired heater or by waste heat, pumped through a shell and tube or plate exchanger against the LNG. The fluid loop decouples combustion from the cryogenic bundle, gives tight control of the LNG outlet temperature, and lets the heat source sit remotely from the cold block, which marine and rooftop installations value. Submerged combustion vaporizers, SCVs, sit at the opposite pole of directness: burner exhaust sparges directly into the water bath, combining combustion heat transfer and bath agitation in one step, reaching the highest duties in the smallest footprint at the cost of the fuel gas consumption and the flue gas stream.

Materials and cryogenic discipline are shared across the types. LNG tubes are stainless steel or aluminum alloys qualified for minus 196 degrees C class service, with austenitic stainless dominating high pressure send out designs; joints, gaskets, and valve trim follow cryogenic practice, extended bonnets and properly specified cryogenic ball valve classes at the block and control points; and thermal contraction is engineered with loops and supports rather than fought. Ice management is a plant discipline: water from defrost and rain must drain, foundation heave must be prevented with insulation and heating under air units, and the plume or fog from an air vaporizer bank is a real neighbors and instrumentation issue at some sites.

Control and safety wrap the train. Outlet temperature control loops modulate LNG flow or heat input to hold the send out temperature band, with low temperature trips protecting downstream steel from cryogenic excursions; pressure control holds the send out header against demand swings; and on fired types, burner management with flame safeguard, fuel gas double block, and a flame arrester philosophy on vent paths governs combustion safety. Gas detection around flanged cryogenic joints, relief valves on the cold side rated for liquid relief, and emergency shutdown isolation complete the standard architecture. A vaporizer without a low temperature trip is a pipeline embrittlement event waiting for its schedule.

Odorization and quality close the process story where the gas leaves to a distribution system. LNG is odorless, so odorant injection at the send out, metered on gas flow, marks the gas for the downstream network, with injection skids, storage, and metering as part of the terminal battery limit. Gas quality instruments, chromatographs and heaters monitoring, confirm the deliverable; a knockout drum or filter protects the pipeline from entrained fluids where the process can carry them. The vaporizer is the last process machine before the meter, and its temperature guarantee is part of the custody quality statement.

Chapter 3 / 06

Vaporizer Types, Site Fit, and Duty Boundaries

Type selection is a site and profile match. Ambient air units suit terminals and stations with moderate humidity climates and a base load profile that rotation defrost can carry, with fans or natural draft by economics; their virtue is zero fuel and zero combustion emissions, their limit is the derate on the coldest, dampest days, precisely when gas demand peaks. Water bath and intermediate fluid units suit peak shavers and industrial stations wanting stable control and fast start; their virtue is controllability and independence from ambient, their cost is the heat input. SCVs suit top end peak duty and backup where fuel is available and emissions permitted; their virtue is duty per footprint and reliability, their cost is the gas burned and the flue stream.

TypeHeat sourceBest fitLimit to manage
Ambient air, natural draftair, no fansbase load terminalsFrost derate, plot area
Ambient air, forced draftair with fanscompact sitesFan power, noise
Water bath, indirect firedburner via bathpeak shavers, satellitesFuel, bath maintenance
Intermediate fluid, IFVfired or waste heatmarine, remote heatLoop complexity, fluid life
Submerged combustion, SCVexhaust in bathpeak and backupFuel 1.5-2% of send out, emissions

Duty boundaries keep the selection honest. The vaporizer is not a storage withdrawal machine: its rate is set by send out demand and its turndown, commonly 10 to 1 on fired units and narrower on natural draft air banks, must cover the demand curve including the cold snap peak. It does not replace LNG pumps or the high pressure send out pump stage, whose head sets the vaporizer inlet pressure and whose cavitation discipline sets the suction conditions. And it is not a gas conditioning plant: heating value adjustment, nitrogen or LPG trimming, is separate equipment whose temperature demands land on the vaporizer's outlet specification.

Where it sits in the plant matters as much as the type. Upstream, LNG pumps at low and high pressure stages feed it through cryogenic piping with proper supports; a knockout drum protects the train where two phase feed is possible; and storage boil off compressors, the vapor recovery unit at terminals, interact with the heat and gas balance. Downstream, the send out header, metering, odorization, and the gas detectors and isolation valves of the battery limit close the train. The vaporizer purchase should draw its battery limit explicitly, heat source utilities in, gas specification out, and make the interfaces someone's line item.

Site ambient and layout close the type decision. Air vaporizer banks need open plot, fog plume tolerance, drainage for defrost water, and foundations protected from heave; water bath and fired units need fuel gas supply, flue stacks with dispersion review, and noise control near boundaries; coastal sites review salt and freeze protection on fans and structures; and cold climate sites push every selection toward more fan power or more fired trim. The site's ambient statistics, dry bulb and humidity exceedance bands, are as much a part of the RFQ as the gas rate, because they define the derate and the backup capacity arithmetic.

Chapter 4 / 06

Key Specification Parameters

The data sheet parameters fall into four groups: rate and conditions, heat source, mechanics, and environmental. Rate parameters are LNG flow at design point, turndown ratio, inlet conditions from the pumps, and send out pressure and temperature with the guarantee band. Heat source parameters are the design ambient basis, the derate curve or supplementary heat strategy, burner duty or fan power or bath heat input, and fuel or electricity consumption at design. Mechanical parameters are design pressures and temperatures, tube materials, surface area or duty rating, and the code basis. Environmental parameters are NOx and other emissions for fired types, noise limits, and plume or drainage provisions. A quotation rated at a single unnamed ambient is not comparable to one with the curve.

ParameterTypical rangeDesign note
Send out rate per train0.5-200 t/hTerminal banks parallel trains
Send out pressureto 100+ bar classSet by pump stage upstream
Send out temperature0-15 C bandPipeline contract number
Turndown10:1 fired, less airMust cover demand curve
Design ambientsite exceedance basisDefines derate and trim
SCV fuel gas~1.5-2% of gasCost and emissions at once
Tube materialsSS or Al alloysCryogenic qualified
Fired emissions NOxper burner classPermit line item
Noisesite limit dB(A)Fans and burners dominate

Derate and backup deserve explicit numbers in every air vaporizer specification. The vendor should state capacity versus ambient temperature and relative humidity, including frost cycle behavior over a 24 hour cold day profile, and the buyer should state the demand duration curve for the same statistics; the difference between the two curves, the capacity shortfall on the coldest hours, sizes the fired or fan supplementary capacity. A terminal that accepts a single point rating will discover its shortfall in January, and the discovery is expensive because backup capacity ordered later costs more than backup ordered with the bank.

Standards ride the pressure parts, combustion, and siting. Vaporizer pressure parts build to the pressure vessel and piping codes with cryogenic material impact requirements; fired units carry burner management and fuel gas safety standards with flame safeguard and double block arrangements; marine units add classification society rules; and siting, spacing, and dispersion studies govern terminal layout with the vaporizer bank treated as a cryogenic source. Relief protection covers the cold side for liquid thermal expansion and blocked outlet scenarios with rated safety relief valves, and gas detection zones cover the joint and flange population. None of these are exotic; all of them are scope boundary items between packages.

Acceptance and performance testing close the sheet. Factory tests cover pressure and leak on the cold circuits and burner package proof where applicable; site acceptance proves rate, send out temperature, and utility consumption at whatever ambient prevails, corrected to design basis by the agreed method; and the derate verification, running a bank through a frost cycle, is the test that matters for air units and should be scheduled in the commissioning plan. A vaporizer accepted on a mild autumn day without its derate behavior verified has not been accepted at all.

The battery limit systems deserve their own data sheet lines because send out quality is a custody statement. Odorant injection runs from a small storage and make down skid through a metering pump paced on gas flow, and its dosing accuracy is a regulatory number on distribution systems. Custody and energy accounting meter the send out with a flow meter corrected for pressure and temperature, and gas quality instruments close the specification. Fan drives on forced draft units increasingly carry a variable frequency drive so the bank can follow the demand curve quietly instead of staging fans hard against the noise limit. None of these items are exotic, and all of them arrive from different suppliers than the vaporizer itself unless the RFQ collects them; the terminal that scopes them at award gets one performance test, and the terminal that does not gets four commissioning arguments.

Chapter 5 / 06

Selection Decision Factors and RFQ Language

Selection starts from the demand and the site statistics, not the catalog. The designer writes the send out profile, annual and peak day, the pressure and temperature specification, the ambient exceedance bands with humidity, the utility prices, fuel gas, power, water if any, and the emissions and noise envelope. From that basis the type mix follows with little freedom: free heat first where ambient permits, fired heat for the shortfall, and rotation or trim to cover the frost hours. An RFQ without the site statistics invites vendors to quote the catalog's favorite ambient.

Duty driverFavored mixWatch item
Terminal base load, moderate climateambient air bankDerate curve vs peak day demand
Terminal with cold snapsair bank plus SCV backupBackup ordered with the bank
Peak shaver, fast startwater bath or SCVStart time and fuel inventory
Marine fuel gas handlingintermediate fluid IFVEngine heat integration, rules
Industrial satellite stationcompact air unit plus trimWinter demand and power cost

Reliability architecture is the second decision and it is made with the profile. How many trains, of what type, cover the peak day with the largest unit out of service; whether backup is fired capacity or rotation margin; and how fast a cold standby unit reaches full rate, minutes for SCVs, longer for cold soaked air banks. Terminals and city gates answer these questions with the regulator at the table, because send out reliability is a public service number. The architecture belongs in the RFQ as a duty statement, letting vendors propose the mix against it.

The RFQ language that returns comparable offers states the basis and the guarantees demanded. State LNG composition and rate profile with peak day duration, inlet pressure and temperature from the pump stage, required send out pressure and temperature band, ambient exceedance statistics with humidity, utilities available and their prices, emissions and noise limits, the reliability architecture required, and the acceptance test basis including derate verification. A complete RFQ paragraph reads: peak day 180 tonnes per hour at 80 bar and minimum 5 degrees C send out, site ambient minus 15 degrees C 98 percent dry bulb with 80 percent relative humidity, ambient air vaporizers with SCV backup such that peak day is met with any single train out, NOx per permit, performance corrected to design ambient by agreed method.

Commercial comparison is only fair on a normalized basis. Offers should be forced onto one table: rate and derate at the stated ambient bands, utility consumption at design and at peak day, emissions and noise, plot area and foundations, reliability architecture delivered, materials and code basis, delivery, and the acceptance test regime including frost cycle verification. The cheapest first cost is very often the air bank with the least surface for the stated rate, and its operating cost lands on the SCV fuel bill every cold day; the comparison that prices the annual heat mix is the one that tells the truth.

Integration questions close the selection. Who owns the pump stage interface and its suction conditions; who owns defrost water drainage, foundation heating, and plume management; who owns the odorant and metering skids at the battery limit; and who owns the backup fuel gas conditioning for the SCV burners. These questions cost nothing to ask before award and a change order each to ask after the first winter.

Chapter 6 / 06

Installation, Standards, Failure Modes, and Maintenance

Installation is a cryogenic and combustion erection by type. Ambient air banks land on heated, drained foundations with lifting frames and fan or stack assemblies; water bath and fired units set on their skids or foundations with flue stacks, fuel trains with double block and vent, and burner management wiring; intermediate fluid loops add the heater and circulation package. Piping follows cryogenic practice, contraction loops, extended bonnet valves, and supports with slide plates; the relief philosophy covers liquid blocking and thermal expansion; and commissioning chills the train down on a controlled ramp, verifies the low temperature trips, proves burner safety on fired units, and runs the performance test at whatever ambient prevails with the agreed correction. The frost cycle verification run belongs in commissioning, not in the first winter.

Failure modes have a known hierarchy per type. On air units, frost choking beyond design and ice bridging between tubes cut capacity, and defrost rotation logic or drainage failures turn a derate into a shutdown; fan and structural icing, and foundation heave where drainage is neglected, are the site discipline items. On water bath and fired units, bath chemistry and freezing protection, burner problems from poor fuel gas conditioning, and stack corrosion head the list; on SCVs, the sparge system and water chemistry govern bath stability, and exhaust gas carryover into the gas side is the classic upset to design out. Across all types, low temperature excursions downstream of the train are the safety critical failure, and the trip and isolation logic exists to prevent them.

SymptomLikely causeFirst response
Send out temperature saggingderate or heat shortfallTrim on, rotation audit, trip margins
Air unit capacity fallingfrost or fan icingDefrost cycle, drainage, fan check
Bath temperature unstableburner or sparge faultFuel gas audit, sparge inspection
Outlet below trip on startcold start bypassRamp procedure, recirculation warmup
Flue gas in gas sidetube or sparge leakIsolate unit, inspect bundle

Maintenance is planned around the heat source and the cold discipline. Air units need fin surface inspection and cleaning where airborne dirt clogs, structural and drainage checks each season, and fan and drive service; water bath units need water treatment, bath inspection, and burner tuning with flue gas analysis on a schedule; SCVs add sparge and bath solids management; and all types need relief valve and trip proof testing, calibration of the temperature and pressure instruments that protect the pipeline, and gasket and insulation integrity walks on the cold circuits. Winter readiness, drainage, trace heating, and defrost logic proving, is an annual ritual, done in autumn.

Operational stewardship is what the purchase actually bought. Trend send out temperature and rate against ambient with the derate curve overlaid, prove the trips on schedule, keep the defrost rotation honest instead of convenient, and hold the fuel gas conditioning for burners to specification. Terminals that know their derate curve from data rather than from the brochure run their backup capacity on purpose, and terminals that do not discover the curve every January from the pipeline operator's phone call.

FAQ

What are the main types of LNG vaporizer?

Four heat sources define the families: ambient air vaporizers passing LNG through finned tube banks warmed by air, water bath vaporizers heating an immersed bundle from a warmed bath, intermediate fluid vaporizers circulating a heated fluid loop against the LNG, and submerged combustion vaporizers sparging burner exhaust directly into the bath for the highest duty per footprint. Many terminals combine types, ambient air for base load with submerged combustion for peak and backup.

Why do ambient air vaporizers lose capacity in cold weather?

Because their air side runs below freezing, atmospheric moisture deposits as frost on the fins, and the frost layer both insulates the surface and chokes airflow, so heat transfer falls over hours of operation. Plants counter with several banks operated in rotation, defrosting each in turn, and accept a derate that steepens as ambient temperature falls and humidity rises. The derate curve versus the site's coldest demand hours is the core arithmetic of air vaporizer selection.

How much gas does a submerged combustion vaporizer consume?

Typically on the order of 1.5 to 2 percent of the vaporized send out, burned to fire the bath, which is why SCVs are usually specified for peak and backup duty rather than continuous base load. That fuel line is both an operating cost and an emissions stream, so terminals with an air or water heat base minimize SCV hours, and the RFQ should state expected annual SCV operating hours to make comparisons honest.

What send out temperature does an LNG vaporizer deliver?

Commonly between 0 and 15 degrees C at the battery limit, with the exact band set by the pipeline or downstream contract, since the downstream steel and metering need a margin above freezing and the gas needs superheat above dew point. The vaporizer control loop holds that band by modulating LNG flow or heat input, and a low temperature trip protects the pipeline if control is lost.

Can one vaporizer handle peak day and normal demand?

Only if its turndown matches the demand curve: fired types commonly reach 10 to 1 turndown with stable outlet temperature control, while natural draft air banks run narrower and rely on rotation and multiple units for range. The specification should state the demand duration curve and require the vendor to map turndown against it, including the peak day with any single unit out of service where reliability architecture demands it.

What utilities does an LNG vaporizer need besides LNG?

By type: ambient air units need fan power where forced draft plus drainage and foundation heating; water bath units need the bath heat source, burner fuel or steam or electric power, and water treatment; intermediate fluid units need the heater fuel or waste heat source plus circulation power; SCVs need fuel gas conditioning and a flue stack. All types need instrument air, power for controls, and gas detection. The utility consumption at design and at peak day belongs in the bid table next to the price.

How is an LNG vaporizer commissioned in warm weather?

The train is chilled down on a controlled ramp, the outlet temperature control and low temperature trips are proven, burner management is safety tested on fired units, and the performance test runs at the prevailing ambient with results corrected to design basis by the agreed method. Critically for air units, the commissioning plan should include a frost cycle verification run and, where the climate allows, a cold morning test, because a unit accepted only on a mild day has never shown its derate behavior.

Sources

  1. Chart Industries, Vaporizers
  2. Chart Industries, Smart vaporizer choices for LNG regasification
  3. Chart Industries, Vaporizer sizing for cryogenic installations
  4. Chart / Thermax, Indirect fired water bath vaporizer (PDF)
Ask SpecForge AI