Vapor Recovery Unit

A vapor recovery unit captures hydrocarbon vapor that storage tanks, truck and rail loading racks, and process vents would otherwise breathe to atmosphere or send to a flare, and returns it somewhere useful: into the sales gas line, back into a storage vessel as recovered liquid, or into the plant fuel system. In its tank-battery form it is a small compressor package that holds a slight vacuum on the vapor space, sweeps the vapors given off as crude or condensate flashes and breathes, and pushes them into the gas sales line. In its loading-rack form it is an adsorption machine, carbon beds that soak up gasoline and chemical vapors displaced during filling, regenerated by vacuum or steam, with the desorbed concentrate returned to storage or fuel.

This page treats the vapor recovery unit as a purchasing object: how vapor generation rates are estimated, how suction pressure control keeps tanks safe while recovering the most vapor, how compressor and adsorbent selection set recovery efficiency and power, and how flashback protection, flame arresters, and inerting keep a machine full of flammable vapor on the safe side of its own chemistry. It sits beside the tank blanketing valve and the pressure vacuum relief valve whose settings define the window it operates in, and in front of the flare stack that burns whatever it cannot take.

Industrial hoses and fluid transfer hardware assembled at a plant, representative of the vapor collection and transfer equipment class that vapor recovery units serve

Photo: Hammelmann Maschinenfabrik, CC BY-SA 3.0, via Wikimedia Commons

The decision concentrates in five places: the vapor source and its generation profile, the suction pressure the tanks can safely hold, the recovery route for the captured vapor, the compressor or adsorbent technology that fits the flow and composition, and the hazardous-area and flashback protection the whole skid carries. Get those right and the package size, power draw, and payback follow.

Chapter 1 / 06

What a Vapor Recovery Unit Is and What Is Being Decided

The machine exists because standing losses are money and regulation at once. Every storage tank with vapor in its headspace breathes: it exhales vapor as liquid fills it and as heat expands the vapor space through the day, and it inhales as liquid is drawn and as night cools. Truck and marine loading displaces vapor continuously at high rate during every fill. Vent those streams and the plant loses lighter hydrocarbons it already paid to produce, and emits volatile organic compounds and hazardous air pollutants that permits increasingly refuse. The vapor recovery unit closes that loop: capture at the source, move the vapor somewhere valuable, and let the flare handle only what recovery cannot.

In the compression form, the unit is a skid with an inlet scrubber, a compressor, a driver, discharge cooling and liquid handling, and a control system whose one governing act is holding suction pressure. The compressor pulls the tank vapor space down to a slight vacuum, typically 5 to 50 millibar below atmosphere or just above the blanketing setpoint, so vapor flows to the unit instead of out the vent. Discharge pushes the recovered gas into the sales line, the fuel system, or a recovery vessel. The sizing logic is a bookkeeping exercise: vapor generated equals stock tank flash gas plus breathing plus standing boil-off, and the compressor must cover the peak hour, not the average, or tanks lift their vents and the recovery quietly becomes intermittent venting.

In the adsorption form, the unit is two or more carbon beds with a vapor header between the loading points and the beds. Displaced vapor passes through the active bed, the hydrocarbons adsorb onto activated carbon, and clean air vents. When the bed approaches breakthrough it swings offline, and regeneration desorbs the captured hydrocarbons in concentrated form, by vacuum pump to a small absorber or recovery compressor, by steam or hot inert gas to a condenser. The two-bed arrangement keeps capture continuous while one bed regenerates. This is the standard machine at gasoline and chemical terminals, where vapor comes in bursts at high rate and the recovered liquid has obvious value.

What is being decided, in engineering terms, is five things: the vapor inventory and its worst hour; the suction pressure window between the tank's mechanical limits, its blanketing system, and its vent settings; the destination for recovered vapor, gas line pressure, liquid recovery, or fuel; the technology, compressor type or adsorbent cycle, that fits that destination; and the safety architecture, flame arrester placement, inerting, and hazardous area classification, that a machine handling saturated hydrocarbon vapor must carry. The paragraphs that follow work through each in the order a project meets them.

A scale tour makes the machine concrete before the engineering begins. At the small end, a single-well battery runs a package the size of a large refrigerator: one rotary vane compressor, a scrubber, and a control panel, recovering a few hundred cubic meters of gas a day into the sales line. At a crude terminal, the unit is a carbon bed pair the size of a shipping container catching vapor from a dozen truck racks between tanker fills. At a major gasoline import terminal, it is a multi-train adsorption plant with its own recovery compressor, absorber, and blower, recovering product by the tankercargo. The machine scales over three orders of magnitude, and the physics at the carbon surface and the suction control loop are the same at every size.

Chapter 2 / 06

How Suction Pressure, Compression, and Adsorption Do the Work

Suction pressure control is the heart of the compression unit and the least forgiving part of its engineering. Tanks are thin-walled vessels with a safe operating window set by their pressure vacuum relief valve settings and their blanketing system: pull too hard and the tank can be drawn toward vacuum; pull too little and the vents lift and vapor escapes anyway. The unit modulates between those walls, typically holding 2 to 10 millibar of vacuum with a control valve or speed control, backing off on high vacuum, adding sweep or make-up gas on low load so the compressor always has flow. The interplay with the tank blanketing valve deserves explicit design: blanketing adds inert gas when vacuum rises, which can chase the recovery unit in a circle, so the setpoints must be stair-stepped, blanketing set to protect, recovery set to collect, with deadband between them.

Compressor selection follows the gas and the destination. Rotary vane and rotary screw machines dominate small tank-battery duty: a rotary vane pump handles the low flows and modest pressures of a single battery with simple mechanics, and screw compressors cover larger flows and higher discharge pressures with oil-free or flooded variants. Liquid ring machines appear where wet, dirty vapor would wash other types. Discharge pressure is set by the sales line or the recovery vessel, and interstage cooling knocks out condensate, which is usually the most valuable part of the stream. Driver economics follow the electricity or gas available, and a vfd on the driver is the modern norm because vapor generation varies around the clock.

Adsorption kinetics set the carbon machine. Activated carbon holds 20 to 40 percent of its own weight in gasoline-range hydrocarbons at terminal conditions, and the working capacity between adsorption and regeneration is a fraction of that, set by the outlet breakthrough target. Vapor passes through the bed at face velocities low enough for the mass transfer front to stay sharp, and the bed switches before that front reaches the far end, monitored by a hydrocarbon analyzer or gas detector at the outlet. Regeneration by vacuum pulls the desorbed concentrate to a small recovery compressor or an absorber column where lean liquid washes it back to storage; steam or inert regeneration sends the concentrate to a condenser instead. The cycle time, bed size, and regeneration energy are the three knobs the vendor balances.

Recovery routing closes the loop and decides the accounting. Sales gas return requires the recovered vapor to be conditioned to line quality, sweet enough, dry enough, heavy enough to meet heating value, which may add a glycol dehydrator or blending with lean gas on the route. Liquid recovery, condensing the heavier fraction and returning it to stock, pays best when the vapor is rich in butanes and pentanes. Fuel gas routing is the simplest destination and the poorest economics. The recovery efficiency the permit records is the fraction of inlet vapor not vented or flared, and well-run units report 95 to 99.5 percent at terminals and 90 to 98 percent on tank batteries.

Safety architecture runs through everything because the working fluid is a flammable vapor near its flammability limits. The inlet line carries a flame arrester between the vapor source and the unit; the skid is classified for hazardous area and its electrical gear, motors, solenoids, instruments, is certified to match; dry screw and rotary vane machines are built for gas service with proper seals; and the control system treats high oxygen, high temperature, and high vacuum as shutdowns, not alarms. Where the vapor can enter the flammable range in the machine, nitrogen inerting or design oxygen limits apply. The VRU is one of the few packages a plant buys whose entire content is an ignitable mixture, and its purchase specification should read that way.

One thermodynamic detail does more design damage than any other: the vapor is not gas, it is a saturated mixture. Tank vapor sits near equilibrium with the liquid below it, so its composition and rate swing with temperature across the day and the season, and any cooling in the piping condenses liquid that the machine must either recover or survive. The inlet scrubber exists for the second reason; the recovered condensate in the first. Design cases should therefore be run at the hottest ambient for maximum vapor rate and richest composition, and at the coldest for liquid fallout in the headers, because the machine that works in April can drown in January or choke in July.

Chapter 3 / 06

Compression Packages and Carbon Adsorption Designs and Duty Boundaries

The compression package, the tank-battery and gas-plant form, is built around steady, modest vapor rates. Its signature hardware is the recovery compressor skid: inlet scrubber with a level transmitter and dump to a closed drain, the compressor itself with its driver and vfd, discharge cooler and knock-out, and controls holding suction. Variants include multi-stage units for high discharge pressure and packages with integral liquid recovery, a cold separator that drops the heaviest fraction back to stock. The compression form wins wherever vapor arrives continuously and a gas destination exists: production batteries, tank farms breathing load, process unit vents with steady composition.

The carbon adsorption package, the loading-rack form, is built around bursts. Its signature hardware is the dual-bed absorber with switching valves, the vacuum or steam regeneration train, and, in the newest terminals, a secondary polishing stage. Between loading arms and the beds sits a collection header with a flame arrester at the boundary; after the beds, clean air vents through a stack. The adsorption form wins wherever vapor arrives in high-rate short bursts with air in the mix, truck racks, rail terminals, marine loading, because the beds act as a chemical accumulator that the regeneration train empties between events. Its weakness is heat: adsorption of hydrocarbons releases heat, and a rich vapor event can warm a bed toward ignition if the design ignores it, which is why monolith or dilution provisions and temperature monitoring are standard.

Hybrid and membrane forms complete the market. Membrane units pass the vapor across hydrocarbon-selective membranes that concentrate organics into a small retentate stream for recovery while permeate vents; they suit streams too lean for economic compression. Hybrid compression-adsorption trains put carbon ahead of a compressor to flatten the load. Absorption units wash vapor with lean oil in a small packed tower. Each has a niche, and the honest selection sequence runs: characterize the vapor, price the recovered product, check the destination, then let the technology fall out, rather than starting from a favored machine.

Duty boundaries against the neighbors deserve plain language. The vapor recovery unit is not a flare stack: the flare destroys and the unit recovers, and the modern permit preference is recovery first with the flare behind it for upsets. It is not a vapor combustor or thermal oxidizer, which are destruction devices for lean streams with no recovery value. It is not tank breathing hardware: the tank blanketing valve adds inert to protect the tank, and the pressure vacuum relief valve is the last mechanical vent, both of which set the window the recovery unit works inside but neither of which recovers anything. It is not a dry screw vacuum pump service either, though a dry screw vacuum pump is exactly what may sit inside its regeneration train; the machine is the package, not any single component.

FormTypical dutyCapture routeWhere it winsWatch-outs
Compression package (tank battery)1,000 to 20,000 m3/d vaporSales gas or fuel lineContinuous flash and breathing lossesSuction window vs blanketing; wet sour gas handling
Carbon adsorption, vacuum regenLoading racks to 1,500 m3/h burstsLiquid recovery to stockTerminal and truck-rack bursts with airBed heat on rich events; carbon change-out
Carbon adsorption, steam or inert regenChemical and gasoline terminalsCondensed concentrateStreams unsuited to vacuum pumpsWastewater or condensate handling
MembraneLean continuous ventsConcentrate to recoveryStreams below compression economicsMembrane fouling; limited turndown
Chapter 4 / 06

Key Specification Parameters

The specification is built from the vapor study outward. The process set states vapor generation in normal and peak hours by source, composition with molecular weight and reactive components, water and contaminant content, and the tank or rack pressure window available. The performance set states required recovery efficiency and its measurement basis, the recovered product destination and its acceptance conditions, and the allowable venting. The mechanical set states compressor or adsorbent type, materials for sour or chemical service, and the skid's area classification. The controls set states the suction pressure band, the shutdown matrix, and the instrumentation, oxygen, temperature, level, and the outlet analyzer. The commercial set states the utilities, power, nitrogen, steam if any, and the expected consumables, carbon, oil, seals.

ParameterTypical rangeWhy it matters
Suction pressure control band2 to 10 mbar vacuum typicalBetween tank protection and vent lifting; the recovery lever
Vapor handling ratePer vapor study peak hourSizes compressor or beds; undersizing leaks vapor at peaks
Discharge pressureSales line or vessel pressureSets stages, power, and cooling duty
Recovery efficiency90 to 99.5 percentThe permit and payback number, measured at the outlet
Carbon working capacity5 to 15 percent of bed massCycle time and bed size on adsorption units
Oxygen limitPer flammability analysis, often 8 to 12 percentShutdown threshold inside the machine
Driver power7.5 to 200 kW typicalOperating cost of compression recovery
Skid area classificationZone 1 or 2 per siteCertified electrical gear throughout

Two lines in that table decide the project's success. The suction band decides how much of the standing loss is actually captured: a unit that controls at atmospheric pressure loses every millibar of tank pressure to the vent, and one that controls below the blanketing setpoint burns inert gas chasing its own tail. The recovery efficiency basis decides whether the number is engineering or decoration: efficiency measured across the unit on design vapor says little unless it is tied to the actual vapor generated at the source, and the acceptance test should state the basis explicitly, inlet vapor measured at the header, outlet measured at vent and at recovered product.

Instrumentation completes the picture and most of it is safety: an oxygen analyzer or gas analyzer at the inlet on streams that can run rich or lean, temperature sensing in carbon beds, level transmitters on every scrubber and separator, a flow meter on recovered gas for the production accounting, and pressure transmitters at suction and discharge. The control system, a small plc tied to the tank farm or terminal system, runs the suction control loop, the bed switching logic, and the shutdown matrix. Remote monitoring has become standard on tank-battery units because the economics of a site visit decide whether a small unit keeps running after the first winter.

Chapter 5 / 06

Selection Decision Factors and RFQ Language

Selection starts with the vapor study, done honestly. For tank batteries it tallies flash gas from the separators and treater pressures against stock tank conditions, breathing from diurnal temperature swing and tank turnovers, and standing losses, using the standing storage loss correlations the EPA provides for the emission side; for loading racks it multiplies loaded volume by saturation and displacement physics for each product and vapor temperature. The study's output is a load duration curve, vapor rate against hours of the year, and that curve, not a nameplate, is what the machine must cover. Underestimate the peak and the vents lift at every truck; overestimate the average and the compressor short-cycles itself to death.

The destination decision follows immediately because it halves or doubles the equipment list. A sales gas line within reach makes compression recovery straightforward and the payback short when vapor is rich. No gas line, and the answer is liquid recovery, condensation or absorption back to stock, which favors the adsorption form with its concentrate stream. A fuel header absorbs recovered gas at fuel value, the floor of the economics. Price the recovered stream at its real disposition, not at crude prices, and put the vapor's lean months in the model, because summer vapor and winter vapor are different fluids.

The technology choice then narrows itself. Continuous load with gas destination points at a rotary vane pump or screw compressor skid with a vfd and suction control. Burst load with air points at carbon beds with vacuum regeneration and a small recovery compressor or absorber. Wet, sour, or fouling vapor pushes toward liquid ring or flooded screw machines and corrosion materials. Lean continuous vents below the compression economics point at membranes or at accepting a destruction device instead, and the honest comparison is recovery value against the capital of each, with the flare or combustor as the fallback that is already there.

A complete RFQ states, on one process data page per source: vapor rate profile with peak and average; composition with molecular weight, water, sulfur, oxygen, and reactive components; available suction window and its relation to blanketing and vent settings; recovered product destination and its acceptance specification; required recovery efficiency and test basis; utilities available including power quality and nitrogen; area classification and hazardous-area certification requirements; ambient extremes; and the emission rules the unit answers to. Vendors quoting against that page are quoting the same machine, and their capture numbers, power draws, and consumable costs become comparable line items rather than brochure prose.

Balance of plant belongs in the same decision. The loading arm hardware and its vapor couplings decide what the rack can actually deliver to the header; a coalescing filter or inlet scrubber protects the compressor from liquids it was never meant to pump; the recovered-liquid return needs a pump or gravity route designed rather than assumed; and the tie-in to the tank's three phase separator or treater vent has to be hydraulically honest about pressure drops. The loading-arm seal quality at the truck connection, where most terminal vapor actually leaks, is a maintenance item wearing an engineering costume, and it belongs on the same project checklist.

The economics deserve their own one-page model because recovery projects live or die on three honest numbers. Recovered vapor value: rate times composition times the disposition price, gas line energy value or liquid product value. Operating cost: driver power, the dominant term on compression units, plus nitrogen or steam on adsorption trains, plus maintenance labor. Capital amortized over a realistic life, ten to fifteen years for the skid with one compressor or carbon renewal cycle inside it. Plot the result against the vapor study's load duration curve and the payback lands between six months and never; the units that pay in months are rich, continuous, and near a sales line, and the ones that never pay are lean, seasonal, and remote, which is exactly the information a project needs before anyone signs.

Chapter 6 / 06

Installation, Standards, Failure Modes, and Maintenance

Installation is skid work plus careful tie-ins: set the package, connect power and any nitrogen or steam, hook the vapor header with its flame arrester at the boundary, run the recovered product line to its destination, and integrate controls. Commissioning proves the suction control loop against the real tank hardware, first by drawing the header down in steps and watching blanketing and vent behavior, then by a controlled recovery run at design rate with the outlet analyzer recording. The acceptance test is the moment to verify the efficiency basis, because rewriting it after signature is a negotiation nobody wins.

The governing references are environmental and safety codes plus the vendor package practice. The EPA Natural Gas STAR program documentation on vapor recovery units is the practical reference for tank-battery recovery economics and the estimation methods behind it, and the EPA fact sheets on vapor recovery towers and units cover the emission-reduction accounting; John Zink and peers document the terminal-side adsorption practice. Mechanical codes for pressure vessels and piping, and the hazardous-area electrical codes, apply as they do to any skid of flammable service. There is no single international product standard for the VRU as a machine; the specification carries the duty, and the codes carry the safety.

Failure modes cluster around control and chemistry. Recovery that stops while the unit runs means suction is controlling above the vent setpoint or the blanketing system is feeding inert faster than vapor arrives; the fix is setpoint bookkeeping between the three systems. Compressor damage means liquid carryover or sour corrosion, answered by the inlet scrubber, its level transmitter, and metallurgy review. Carbon beds that heat up mean rich vapor events beyond design, answered by dilution control and temperature trips. Lost efficiency at the outlet means carbon exhaustion or analyzer drift. Shutdowns on oxygen mean air entering through open hatches or bad seals at the truck connection. Each symptom has a small cause set, and the instruments that catch them are the ones the specification insisted on.

SymptomLikely causeFirst action
Unit runs but vents still liftSuction setpoint above vent pressure, or peak beyond capacityRe-stack suction, blanketing, and vent setpoints; re-run vapor study on peak hour
Compressor tripping on liquidCarryover from tanks or scrubber dump failureVerify scrubber level transmitter and dump logic; add coalescing at inlet
Carbon bed temperature climbingRich vapor burst beyond design capacityAdd dilution control; verify bed design against current products
Outlet analyzer reads highBed breakthrough or analyzer driftShorten cycle; calibrate analyzer with certified gas
Oxygen shutdowns recurringAir ingress at hatches or truck couplingsLeak survey with a gas detector; repair seals and gaskets

Routine maintenance is the machine's real economics. Compression units want oil or seal checks, filter changes, valve wear attention on vane machines, and the scrubber dump exercised; adsorption units want bed temperature trending, valve position cycle counts, vacuum pump or recovery compressor service, and carbon assay at each year to plan change-out before breakthrough, not after. The recovered-gas flow meter calibration keeps the accounting honest, and the oxygen and hydrocarbon analyzers want certified calibration gas on schedule. None of this is heavy work; all of it is skippable, and the units that skip it are the ones that quietly become flare loads again.

The institutional item is the same as for any recovery machine: keep the feed honest. Tank mixes change, new products arrive at the rack, treater pressures move with the field, and each change moves the vapor curve the unit was sized on. A standing review, the vapor study re-run against a year of recovered-gas flow meter data whenever the facility changes, keeps the machine matched to its feed, and the divergence between the two is the early record of a recovery unit drifting out of coverage.

Spares and vendor support close the commercial picture. Carry vane or screw machine seal and valve kits, filter elements, solenoid and switching valve rebuild kits for the bed logic, certified calibration gas for the analyzers, and, on adsorption units, an agreed carbon supply with assay service. Ask each bidder at purchase time for the price of a compressor overhaul and a carbon change-out delivered to site, for the remote monitoring they actually provide rather than describe, and for the name of the technician who will commission the unit. The differences between vendors on those three lines are the differences the plant will live with for a decade.

FAQ

How does a vapor recovery unit differ from a flare stack?

The flare burns vapor to destroy it; the recovery unit captures vapor and returns it as sales gas, recovered liquid, or fuel. The modern sequence is recovery first, with the flare behind it for upset duty, and many permits now expect exactly that hierarchy at tanks and loading racks.

What suction pressure should the unit hold on my tanks?

A slight vacuum, typically 2 to 10 millibar, stacked carefully against the blanketing system above it and the vent settings below it. Pull harder and you fight the blanketing valve and risk tank vacuum; pull softer and vapor escapes through the vents. The setpoint bookkeeping between all three systems is the core of the control design.

How is the vapor load actually sized?

From a vapor study: flash gas from separator and treater conditions against stock tank conditions, breathing from diurnal swing and turnovers, and loading displacement at the rack, each with composition. The machine is sized on the peak hour of that curve, not the average, because undersizing shows up as vents lifting exactly when trucks are loading.

When is carbon adsorption the right choice over compression?

When vapor arrives in high-rate bursts mixed with air, the loading-rack profile. Carbon beds act as a chemical accumulator, soaking the burst and regenerating between events, while a compressor would need to be enormous to catch the peak. Continuous vapor with a gas destination points back to compression.

What recovery efficiency should I expect?

95 to 99.5 percent at well-run terminals and 90 to 98 percent on tank batteries, measured across the unit on real inlet vapor. Insist the acceptance test define the basis, inlet at the header and outlet at vent and recovered product, because an efficiency quoted against a design vapor says nothing about your tanks.

What safety provisions does the skid need?

A flame arrester at the vapor boundary, hazardous-area certified electrical equipment throughout, oxygen and temperature monitoring with trip logic, and inerting or design limits wherever the vapor can pass through its flammable range inside the machine. The working fluid is an ignitable mixture by definition; the specification should read that way.

How does the unit interact with tank blanketing?

By setpoint stair-stepping. Blanketing protects the tank and adds inert when vacuum rises; recovery collects vapor and creates that vacuum. Design the recovery suction band just above the blanketing add point with deadband between, or the two systems chase each other and burn inert gas for nothing.

Sources

  1. US EPA Natural Gas STAR - Vapor recovery units
  2. US EPA - Use of vapor recovery towers and VRUs to reduce emissions (PDF)
  3. John Zink - Vapor recovery units
Ask SpecForge AI