Delayed Coker

A delayed coker is the refinery unit that upgrades the bottom of the barrel by thermal cracking: vacuum residue is heated rapidly in a fired heater to cracking temperature, then flowed into a tall coke drum where the reactions begun in the heater continue just long enough, delayed, for the residue to crack into gas, naphtha, gas oils, and solid petroleum coke before the drum fills. When a drum is full, the feed switches to its partner, and the full drum is steamed, quenched with water, drained, opened, and cut, high-pressure water bores and cuts the coke out for handling to storage, then the drum closes, warms, and rejoins the cycle. The vapors meanwhile fractionate continuously in a coker fractionator into wet gas, naphtha, and coker gas oils; OSHA's delayed coker hazard bulletin and Chevron Lummus technology sheets describe the process, and this page treats the complete unit, drums, heater, fractionator, and switching, as the purchasing object.

This page is written for the engineer specifying a delayed coker for bottoms conversion, a capacity or coke-type change, or a safety-driven revamp. It works through what the unit does and what is actually being bought, how the heater and drums do the work, which design choices such as drum pairs, cycle time, and unheading systems separate one offering from another, the parameters that recur on licensor data sheets, and the selection factors and RFQ language that decide whether the unit makes its liquid yields and coke quality for a cycle discipline that keeps people safe.

Tall cylindrical steel process equipment installed at an industrial site, representative of the vertical pressure-vessel hardware class that coke drums are built from

Photo: Sludge G, CC BY-SA 2.0, via Wikimedia Commons

The decision concentrates in five places: the residue feed and its contaminants, since concarbon, sulfur, and metals write the coke yield and quality; the heater, its outlet conditions and the velocity that limits coking in tubes; the drum system, pairs or larger sets, cycle length, and the quench and warm-up discipline that protects them; the fractionator and gas plant that recover the liquid yield; and the coke handling and unheading systems, where the unit's safety and labor reality live. Get those right and the cycle runs like clockwork instead of a fight.

Chapter 1 / 06

What a Delayed Coker Is and What Is Being Decided

The machine this page describes is a thermal cracking train with a batch heart. Fresh vacuum residue mixes with heavy coker gas oil recirculated from the fractionator, passes through a fired heater with high tube velocities and short residence that raise it to roughly five hundred degrees Celsius without letting it coke in the tubes, and enters one of a pair or set of coke drums where the remaining residence, minutes at drum conditions, completes the cracking; light products leave the drum top as vapor for the fractionator and the carbon concentrates into a solid coke mass filling the drum over hours. Drum sets alternate: while one fills, its partner steams, quenches, drains, unheads top and bottom, is hydraulically cut, reheads, warms, and returns. The fractionator, a tall packed or trayed tower in the unit's middle, splits drum vapor continuously into gas, naphtha, and gas oil products.

What is being decided when a delayed coker is purchased is a yield and availability statement with a safety case. The buyer is purchasing the conversion of a stated residue at a stated rate into a stated liquid yield slate and a stated coke quality, grade or fuel or needle, with a drum cycle that holds, measured in hours, an on-stream factor that holds, and an unheading and cutting system whose safety case the licensor can defend. Everything on the data sheet, drum size, heater duty, cycle time, fractionator arrangement, exists to support that statement, and honest licensors size from pilot coking data on the actual residue rather than by copying the last project.

The delayed coker sits in the bottoms-upgrading family with well-defined neighbors that this encyclopedia treats separately. It is not the fired heater it contains, which is the unit's organ and shares refinery furnace practice but has its own page, any more than it is the fractionator, whose packed tower and reboiler machinery this encyclopedia covers separately. It competes with residue hydrotreating, the hydrotreater family's top-severity branch, which treats bottoms under hydrogen instead of coking them, and with visbreaking, its milder thermal sibling that this page's Selection chapter may contrast without opening a leaf. Its feed comes from the crude and vacuum units downstream of the electrostatic desalter; its wet gas goes to the gas plant and its sour streams to the amine unit and sulfur recovery unit; and its coker naphtha and gas oils hydrotreat, in the hydrotreater units this site keeps, before blending or conversion.

Different buyers buy the same unit for different barrels. A fuels refinery on medium sour crude buys a coker to convert vacuum residue into liquids and fuel-grade coke, the classic economics. A complex refinery running heavy Canadian or Venezuelan feeds fights shot coke, high concarbon, and fouling, and buys drum metallurgy, cycle discipline, and cutting systems for the harder duty. A needle coke producer buys the whole unit around anode-grade or needle-grade coke quality, feed purity, and the slow drums and handling that specialty coke demands. A small refinery may run a two-drum unit on a 24-hour cycle; the world's largest run six or eight drums on shorter cycles. The residue writes the yields, the coke, and the fight.

The economics deserve their own paragraph because the coker converts the refinery's cheapest barrel into its margin. Vacuum residue otherwise sells as bunker fuel or asphalt at a discount; the coker cracks it into naphtha and gas oils that process into transportation fuels, leaving coke whose value ranges from fuel to anode to needle premium. Liquid yield, typically seventy-plus percent by mass, against coke and gas, is the unit's value statement; availability, protected by the drum cycle and the cutting system, is its cash register; and the coke market's logistics, pit, pad, rail, or ship, set the downstream handling investment that travels with the unit decision.

A short tour of the cycle makes the unit concrete. Feed switches to the empty drum at hour zero; the drum fills with coke and vapor for roughly half the cycle; switch valves divert feed to the partner drum and steam strips the full drum's remaining vapor to the fractionator; quench water floods and cools the coke over hours; the drum drains its water to the blowdown system; unheading systems open top and bottom heads; the cutting derrick drills a pilot hole and hydraulically cuts the coke into the pit or pad below; the drum reheads, warms on vapor, and rejoins the feed schedule. Every hour of that cycle repeats, day and night, for the unit's life.

Chapter 2 / 06

How Heater, Drums, and Cycle Do the Work

The chemistry is thermal cracking's free-radical cascade. At heater outlet conditions the residue's large molecules crack into smaller liquids and gas, and the asphaltene-rich remainder condenses and dehydrogenates toward solid carbon; the unit's trick is delay, running the heater fast and hot so little cracking happens in the tubes, then giving the drum the residence where cracking and coking complete. Severity lives in the heater outlet temperature: hotter buys liquid yield and lighter coke, colder buys cycle length in the heater, and the optimum tracks the residue's concarbon and the coke market's demands.

The heater is the unit's precision organ. Multiple passes, high mass velocity in the tubes, and short residence keep tube metal from coking while the fluid reaches cracking temperature; tube metal temperature, velocity, and the fired heat flux profile are the design's watched numbers, and periodic spalling or steam-air decoking cleans the tubes when margins close. Fuel firing, burner management, and the draft system share refinery fired-equipment practice, the industrial burner and heater disciplines this encyclopedia keeps on their own pages. A heater run length between decokes matched to the turnaround calendar is part of the purchase, not an afterthought.

The drums are the unit's heart and its hazard. Tall vessels, typically twenty to forty meters, coke-filling over the on-stream half of the cycle, they run quiescent, a vapor space above a growing coke mass, with drum pressure and overhead vapor velocity the design constraints, velocity too high carries foam and coke fines to the fractionator, and antifoam injection manages the foaming tendency. Drum walls cycle thermally every drum cycle, hot feed to quench water, and the fatigue that writes is the unit's life-limiting physics, which is why drum life, weld surveys, and the cycle's quench discipline are engineering topics in their own right.

Switching is the batch logistics that never stops. At switch time, the four-way or pair of switch valves, among the unit's most critical and most abused equipment, divert heater effluent from the full drum to the warm one in a choreographed minute; the full drum steams to strip, and the blowdown system, its own tower and condensing train with a knockout drum on the gas path, recovers the quench and steaming vapors and oils the water back to the sour water system. Slow or mismanaged switches leak, foam, and surge; fast switches shock drums and heaters; the switch procedure and its valve quality are the unit's operational signature.

Cutting is the hydraulic mining operation at the unit's core. After draining, the unheading systems, bottom and top, open the drum, modern designs fully mechanized remote unheading that keeps operators off the heads, and the cutting structure lowers a combined drill and cutting tool: first a pilot bore through the coke's center, then cutting nozzles swung and rotated under high-pressure water, often beyond three hundred bar, slicing the coke mass into chunks that fall to the pit, pad, or direct rail car below. Cutting water recirculates through settlers and the coke fines handling system; the derrick's machinery, hoists, rotation, and the water units, is a high-pressure plant of its own.

The fractionator and gas train recover the value continuously. Drum overhead vapor quenched and washed enters the fractionator, whose lower section condenses and washes back heavy recirculate to the heater while upper sections draw wet gas, naphtha, and light and heavy coker gas oils; the wet gas compresses, in a centrifugal compressor or, on small units, a reciprocating compressor, and heads to the gas plant's amine unit and sulfur recovery chain for its hydrogen sulfide, which is copious, while the sour water from steaming and quenching strips in the sour water stripper. The blowdown train's own tower condenses quench and steaming vapors through a three-phase separator drum and its knockout drum on the gas path, oiling the water back to sour water. Products hydrotreat downstream: coker naphtha and gas oils are classic feeds for the hydrotreater family, and the unit's liquid value is realized there.

Chapter 3 / 06

Unit Types, Coke Products, and Machine Boundaries

Drum arrangements name the unit classes. The classic pair, two drums alternating on cycles from 24 to 18 and fewer hours, dominates small and mid-size units; larger units run two pairs on staggered schedules; the largest modern trains run six or eight drums with short cycles and massive cutting infrastructure. Zero-recycle once-through designs maximize coke; high-recycle designs trim coke and lift liquid yield; and cycle length itself is a severity lever, shorter cycles buy throughput at drum-life and safety-discipline cost, which is why the cycle decision belongs to the buyer's stated values.

Coke products name the market classes. Fuel-grade coke, sponge or shot by morphology, sells on heat content with sulfur and metals limits, and shot coke, the unwanted-but-sometimes-demanded pellet form of high-asphaltene feeds, punishes cutting and handling. Anode-grade coke for aluminum smelting demands low sulfur and metals and controlled porosity, writing feed slate and severity discipline. Needle coke, the graphite electrode precursor, demands feed purity, low severity, long cycles, and specialized handling, and commands the premium that justifies a unit built around it. Coke quality, not just tonnage, belongs in the yield statement the unit is bought against.

Unheading and handling systems name the unit's generation. Traditional bolted heads and hand unheading survive in older units and none should be bought new; modern units run fully mechanized bottom and top unheading, remote-actuated, that keep operators off the drum heads through the cycle's most dangerous minutes. Coke handling ranges from the classic pit with crane and pad drainage, to pad mounding with front-end loaders, to direct rail or slurry systems; each writes its own water management, fines capture, and storm-water discipline. The handling choice travels with the site's logistics and is part of the purchase's scope, not its periphery.

Adjacent machines mark the boundary. The delayed coker is not the fired heater, the packed tower of its fractionator, or the steam drum it may share utilities with, all organs with their own pages; it is not the hydrotreater family it feeds, nor the electrostatic-desalter front end of the crude train it draws from; and it is not the sulfur recovery unit or amine unit that clean its copious sour gas. Its wet gas compressor, blowdown system, and cutting water plant are organs internal to this unit's scope. Upstream, the vacuum unit delivers residue; downstream, hydrotreaters take its liquids, the gas plant takes its gas, and the coke system takes its solid, and the flare-stack takes what upsets everything.

Utilities and integration complete the installed unit. The refinery's steam boiler house supplies the stripping and purge steam the cycle consumes, with returned condensate cleaned through a condensate polisher on the power side; the site's water balance sees the coker's quench and cutting demands, condensing where it can against the cooling tower network; heat integration recovers fractionator and blowdown heat through a shell-and-tube heat exchanger network; the wastewater side carries oils and sulfides to sour water stripping and an induced gas flotation train on the treatment plant; and the unit's electrical loads, heater, compressors, cutting pumps, are fed from the refinery grid with the emergency discipline its hazards demand. Coke handling moves the cut product by front-end loader and a belt conveyor to storage or rail, and the cutting water header runs through a control valve and pressure transmitter on its way to the derrick. Instrumentation, drum level by nuclear or profile technologies, switch-valve position proofing, and the analyzers on gas and products, closes the loops the cycle lives on.

Chapter 4 / 06

Key Specification Parameters

The licensor data sheet for a delayed coker centers on feed, drums, heater, and cycle, and each number carries a duty consequence. The table below lists the parameters that recur across offerings for fuels and specialty duty, with typical ranges a buyer will see. Values for a specific project come from the residue assay and pilot coking data and the yield and coke targets, and the ranges here are orientation, not a substitute for that engineering.

ParameterTypical catalog rangeWhat it decides
Residue throughputunit specific, thousands of BPDDrum count and size; heater duty
Drum dimensionsroughly 6 to 10 m diameterCoke capacity per cycle; vapor velocity
Drum pressure1 to 4 bar g classYield slate; foaming; compression load
Heater outlet temperatureroughly 480 to 505 CSeverity; liquid yield; coke quality
Cycle time12 to 24 h per drum pairThroughput; drum life; safety workload
Recycle ratioa few percent to 30+ percentCoke yield; liquid yield; heater duty
Coke yieldfeed dependent, 15 to 35 percentCoke system sizing; unit economics
Liquid yield60+ percent typical targetThe unit's value statement
Heater run lengthmatched to turnaround yearsDecoking cadence; availability
Drum design lifefatigue-basis years by cycleReplacement planning; cycle discipline

Three of these numbers deserve the buyer's suspicion when they arrive without a basis. Cycle time quoted without the quench and warm-up discipline it assumes trades safety and drum life for throughput quietly. Coke yield quoted without the feed's concarbon and sulfur is a number from someone else's barrel. Drum life quoted without the fatigue analysis basis, cycle temperature range and transitions, is a label. An RFQ that demands the fatigue basis and the pilot coking data behind the yields separates engineered offers from assembled ones.

Materials and construction follow the hazards. Drums are thick carbon or low-alloy steel designed to the pressure code's fatigue provisions for the cyclic service; the heater runs alloy tubes in refinery furnace practice; switch valves are coking-service specials with purge and proofing; unheading systems are pressure-boundary machinery with their own qualification; and the cutting plant is a high-pressure water system with interlocks and relief. The blowdown system is a coded pressure train of its own. Every one of these components has an inspection and maintenance life the purchase should anticipate, because the coker's availability arithmetic is dominated by them.

Chapter 5 / 06

Selection Decision Factors and RFQ Language

Selection starts with the residue, not the catalog. The assay, concarbon, sulfur, metals, asphaltenes, and the distillation envelope, writes coke yield and quality, heater fouling tendency, and the foaming the drums will fight; pilot coking on the actual residue, or commercial data on its twin, is the honest basis of the yield statement, and a licensor quoting without it should be asked why. The feed slate's future matters as much as its present, because units outlive crude slates, and flexibility bought now is availability later.

The cycle and drum decision is the unit's moral center. Shorter cycles buy throughput and cost drum fatigue, quench stress, and the safety workload of more switches and cuts per year; drum count and size trade against cycle length at fixed throughput; and the unheading and cutting systems' generation, mechanized, remote, interlocked, decides whether the cycle's dangerous minutes are survivable by design. The buyer should state the on-stream factor and the safety case expected, and hold offers to them, because the industry's worst days have all been coker-cycle days.

The table below organizes the decision into the factors that recur across projects, with the questions the buyer should be able to answer before the RFQ goes out. Each row is a place where an incomplete answer becomes an underspecified unit and an availability or safety argument later.

Decision factorWhat the buyer must stateConsequence if left open
Residue assayConcarbon, sulfur, metals, asphaltenes; future slateYields and coke quality guessed; guarantee void
Yield and coke slateTarget liquid yields; coke grade and marketCoke system mismatched; economics wrong
Cycle and drumsCycle length intent, drum count, on-stream factorFatigue and workload traded away silently
Safety systemsUnheading generation, switch proofing, quench disciplineThe unit's hazards land on the operators
HeaterRun length, decoking method, fuelAvailability dominated by heater outages
Fractionator and gas plantProduct slate, compression, sour gas interfacesDownstream bottlenecks discovered late
Coke handlingPit, pad, rail, or slurry; water managementHandling capital and permits late

RFQ language for a delayed coker should name the barrel and the cycle. A workable specification states: residue source and assay with design and maximum rate and future slate flexibility; target yield slate and coke quality with the market basis; drum arrangement, cycle length, and on-stream factor intent with vendor free to propose; heater design basis, outlet conditions, run length, and decoking method; unheading systems fully mechanized and the switch-valve specification with purge and proofing; cutting system scope, water pressure and flow, derrick, and coke handling to pit, pad, or direct loadout; fractionator arrangement and product draw slate with wet gas compression; blowdown system scope; sour gas, sour water, and flare interfaces; utilities, steam, water, and power demands; and the acceptance basis, yield verification against pilot data, a witnessed drum cycle, and the safety systems demonstrated. Naming the interface equipment, vacuum unit upstream, hydrotreater and gas plant downstream, lets licensors bid the connections correctly.

Chapter 6 / 06

Installation, Standards, Failure Modes, and Maintenance

Installation is heavy-vessel and systems work. Drums set in structures with the derricks and unheading machinery; the heater builds in furnace practice; the fractionator and blowdown towers raise; and the cutting water plant, coke handling, and utilities complete a small plant's worth of steel. Commissioning dries and cures, introduces feed at reduced rate with the first drums' cycles tuned, and proves the switch, quench, unheading, and cutting choreography empty and then loaded; the first full cycles calibrate the schedule the unit will keep. Operator training on the cycle's hazards is commissioning's center, because this unit's startup is a school.

Standards for cokers are pressure, safety, and refining practice rather than a single machine standard. Drums and pressure systems follow the pressure equipment code of the jurisdiction with fatigue provisions for cyclic service; the heater follows refinery fired-equipment practice; process safety follows the major-hazard regulations and the industry's coker-specific guidance, OSHA's bulletin among the public statements, on unheading, switching, and hot work; and water discharge follows the site's permits. There is no single international coker standard governing the unit end to end, so the RFQ must name the applicable pressure, mechanical, and safety codes and the licensor's own design standards for drums, unheading, and switching. Edition references should be verified current at purchase rather than copied from an old specification.

The recurring failure modes concentrate in the cycle's violent parts. Drum fatigue, thermal cycling's slow crack propagation at welds and cones, is the life-limiting mode, surveyed by inspection campaigns and managed by cycle discipline, controlled quench rates and warm-ups; switch-valve failures leak and stick, fought by purge systems, proofing, and maintenance; heater tube coking raises metal temperatures until decoking restores it; foaming surges carry coke fines to the fractionator when antifoam and velocity management fail; and the unheading and cutting systems, high-pressure water and heavy machinery, suffer the wear and the incidents their energy implies. Blowdown fouling and sour water corrosion attack the recovery train. Each mode has an inspection or monitoring signature, and the unit's safety case is the maintenance plan.

Maintenance planning is cycle-shaped and campaign-heavy. The table below lists the recurring items with the typical cadence a plant will schedule, assembled from common practice; the real schedule follows the drum cycle's rhythm and the inspection codes' intervals for the pressure systems.

ItemTypical actionTypical cadence
Drum cycle disciplineVerify quench and warm-up rates; log cycles and fatigueEvery cycle
Switch valvesInspect seats and purges, proof position switchesMonthly to quarterly
Unheading systemsService actuators and seals per vendorEach cycle to monthly
Cutting systemInspect derrick, hoses, nozzles, water unitsEach cycle to monthly
Heater tubesMonitor tube metal temperature; spall or decokeContinuous trend, decoke per run
Drum welds and conesFatigue inspection campaignMulti-year program
Blowdown and sour waterInspect fouling and corrosion, wash trainsTurnaround

Long-term care keeps the unit's clock honest. Feed slates drift toward heavier residues and the cycle tuned for one barrel shortens on the next; periodic yield and drum-life re-projection against the current assay retires assumptions before they retire availability. Unheading retrofits pay the largest single safety dividend on older units, and cycle-length optimization, drums, quench discipline, and antifoam programs, trades throughput against fatigue with engineering rather than habit. The plant that treats the coker's cycle as its heartbeat, measured every switch and inspected every campaign, is the plant whose bottom-of-the-barrel margin survives the decade.

FAQ

How does a delayed coker work?

In a loop of continuous fire and batch drums. Vacuum residue mixed with recycle heats fast in a fired heater to about five hundred degrees Celsius, with tube velocity and short residence delaying coke formation until the drum; there, over hours, the cracking completes, vapors leave the top for the fractionator, and the carbon concentrates into a solid coke mass. When the drum fills, feed switches to its partner and the full drum is steamed, water-quenched, drained, opened top and bottom, and hydraulically cut, high-pressure water boring and slicing the coke out, then it closes, warms, and rejoins the cycle. The delay in the name is the design's trick: cracking held off until the drum, so the heater tubes survive.

What are the products of delayed coking?

Gas, liquids, and solid coke. The overhead vapors fractionate into fuel gas, LPG-range material, coker naphtha, and light and heavy coker gas oils, the liquids hydrotreating downstream into fuels and blend stock; together they typically run well past sixty percent of feed by mass. The solid is petroleum coke, fuel grade, anode grade, or needle grade by feed and severity, whose market sets part of the unit's economics. The split among them, set by severity and recycle, is the yield statement the unit is purchased against.

What is the drum cycle and why does its length matter?

The drum cycle is the batch heartbeat: fill, switch, steam, quench, drain, unhead, cut, rehead, and warm, repeating on every drum for the unit's life. Cycle length trades throughput against everything else: shorter cycles raise capacity but add thermal stress, consuming drum fatigue life, and multiply the number of switches and cuts per year, which is to say the unit's hazardous operations. Modern units run 18 hours and below where drum life and discipline support it. The cycle decision belongs in the RFQ with the drum count and the on-stream factor, not in an operator's habit.

What is shot coke and how is it avoided?

Shot coke is the pellet-like coke that forms when high-asphaltene, high-concarbon residues crack too aggressively, the asphaltene spheres agglomerating instead of forming the porous sponge structure cutting systems and markets prefer. It is fought with severity management, lower heater outlet temperature, higher drum pressure, and higher recycle to moderate the reactions, and with feed blending when the slate allows. It matters because it punishes cutting, plugs drums and handling, and discounts the coke market; a unit running a shot-prone slate should have the severity levers and the cutting system bought for that reality.

What are unheading systems and why do they matter so much?

Unheading systems open and close the coke drums' top and bottom heads between fills. They matter because opening a drum of hot, wet, gas-bearing coke is the unit's most dangerous operation, the scene of the industry's worst coker incidents; traditional bolted heads put operators with tools directly in front of that energy. Modern fully mechanized, remote-actuated unheading keeps people off the heads entirely and is interlocked with the cycle, and no new unit should be bought without it, while older units retrofit it as their highest-value safety project.

How is petroleum coke removed from the drums?

By hydraulic cutting. After quench and drain, with the drum opened top and bottom, the cutting derrick lowers a drill stem with a combined boring and cutting head: a pilot bit bores the center passage, then high-pressure water jets, often above three hundred bar, swing and rotate to slice the coke mass into chunks that fall to the pit, pad, or direct rail below. The cutting water recirculates through settlers with the fines captured for handling. It is mining machinery living inside a refinery, and its reliability is the unit's availability.

What should a delayed coker RFQ include?

State the residue assay with design and maximum rates and the future slate; target liquid yield slate and coke quality with the market basis; drum arrangement, cycle length, and on-stream factor intent; heater design basis with run length and decoking method; fully mechanized unheading and the switch-valve specification; cutting system scope with water pressure, derrick, and coke handling to the chosen route; fractionator and wet gas compression slate; blowdown system scope; sour gas, sour water, and flare interfaces; utility demands; and the acceptance basis, yields verified against pilot data, a witnessed drum cycle, and safety systems demonstrated. Naming the vacuum unit upstream and the hydrotreater and gas plant downstream lets licensors bid the connections correctly.

Sources

  1. US OSHA Hazards of Delayed Coker Unit Operations SHIB (PDF)
  2. US EPA Hazards of Delayed Coker Unit Operations (PDF)
  3. Chevron Lummus Global delayed coking tech sheet (PDF)
  4. Becht delayed coking process technology (PDF)
Ask SpecForge AI