An electrostatic desalter is the refinery vessel that prepares crude oil for distillation by washing it with dilution water and then coalescing the resulting brine droplets in a high-voltage electric field so they settle out, taking the crude's salt, residual water, and suspended solids down to the levels the crude distillation unit's corrosion budget allows. Crude and a few percent of hot water pass a mixing valve that disperses the water into droplets, the emulsion enters a horizontal vessel between energized electrode grids, and the field's gradient forces the water droplets, saltier and far more polar than the oil, to collide, coalesce, and fall as brine while the desalted crude flows on. NATCO and Cameron Electro-Dynamic desalters are representative of the industrial class, and this page treats the complete system, vessel, electrodes, transformers, and mixing, as the purchasing object.
This page is written for the engineer specifying an electrostatic desalter for a new crude unit, a capacity or crude-slate change, or a retrofit that must hit tighter salt targets. It works through what the machine does and what is actually being bought, how the field and the mixing do the work, which design choices such as stage count and field type separate one offering from another, the parameters that recur on vendor data sheets, and the selection factors and RFQ language that decide whether the crude unit's overhead corrosion stays inside its budget.
The decision concentrates in five places: the crude slate and its salt, water, and solids content, because every downstream number follows from it; the dilution water, its quality, rate, and source, which sets the wash the field must separate; the mixing intensity, valve or static, that disperses the water without making an emulsion the field cannot break; the vessel and field design, stages, electrode type, AC or AC/DC, and residence; and the brine and interface management that keeps oil under and water over their respective limits. Get those right and the salt target follows with margin.
Chapter 1 / 06
What an Electrostatic Desalter Is and What Is Being Decided
The machine this page describes is a large horizontal pressure vessel, typically sized for the crude unit's throughput with ten to thirty minutes of residence, fitted internally with two or more electrode grids hung on insulators, fed by high-voltage transformers mounted on or beside the vessel. Crude arrives hot from the preheat train, a few percent of dilution water is injected and dispersed through a mixing valve or static mixer, and the emulsion distributes into the vessel's electric fields; droplets polarize, attract, coalesce, and grow until gravity wins and they fall through the water phase boundary as brine. Desalted crude leaves from the top of the oil zone, brine leaves from the bottom for water treatment, and a level interface control holds the oil-water boundary between the electrode field and the brine draw.
What is being decided when a desalter is purchased is a salt-and-solids statement for the crude unit's feed. The buyer is purchasing the ability to take a stated crude slate at a stated rate, with stated inlet salt, water, and solids, down to a stated outlet salt, commonly a few pounds per thousand barrels, and water and solids low enough that the crude distillation unit's overhead corrosion and fouling stay inside their budgets. Everything on the vendor data sheet, residence, field voltage and gradient, stage count, mixing energy, exists to support that statement, and honest vendors size from crude assay and desalting tests on the actual slate rather than by copying the last project.
The desalter sits in the refinery's front-end family with well-defined neighbors that this encyclopedia treats separately. It is not the heater treater of oilfield production, the vessel that breaks production emulsions with heat, chemicals, and often a gentler field at the wellsite; when the stream is refinery scale and the duty is feed preparation, the electrostatic desalter is the machine, and the heater treater page says so. It is not a three-phase separator, which splits gas, oil, and water by gravity alone without a field; not an oil-water separator or a coalescing filter, which polish produced water or refined streams; and not an electrostatic precipitator, which removes particulates from gas with a field of the same physics family. Upstream, the preheat train's exchangers and possibly a fired heater bring the crude to temperature; downstream, the crude column takes the desalted feed, and the brine goes to water handling.
Different buyers buy the same machine for different slates. A coastal refinery on medium crude runs single or two-stage desalting to a few pounds per thousand barrels with modest water and power. A refinery running heavy, high-salt crudes, Venezuelan or Canadian blends among them, fights conductivity, solids, and stable emulsions, and buys two stages, high-voltage dual-grid fields, demulsifier programs, and wash-water rates at the high end. A hydrotreating-integrated unit counts the sodium and solids its downstream hydrotreater catalyst can tolerate and tightens the desalter target accordingly. An offshore platform desalts to protect a compact crude unit with the same physics at smaller scale. The slate writes the specification.
The economics deserve their own paragraph because the desalter is bought with corrosion money. Salt carried forward hydrolyzes in the crude column's overhead to hydrochloric acid, and every pound of salt the desalter misses pays out in overhead corrosion, fouling, and the neutralizing chemicals that follow; solids load the column's bottoms and exchangers. The operating costs are dilution water, heating it and the crude to desalting temperature, electrical power for the fields, and the demulsifier program, and the trade between them, more water and power against less downstream corrosion, is the selection's real optimization. A buyer who compares offers on vessel price alone has compared the smallest number in the least important column.
A short tour of named duties makes the machine concrete. At a large coastal refinery, a charge centrifugal pump moves crude from tankage through the preheat train, desalts in a two-stage train, 5 percent wash water per stage, AC/DC composite fields at high voltage, and leaves under two pounds per thousand barrels on the way to the crude column. At an inland refinery on a single heavy slate, a single large desalter with dual-gradient fields and a strong demulsifier program holds a looser target with minimum water. At an offshore platform, a compact vertical unit desalts wellhead crude before pipeline shipment. Each duty names the same knobs, water rate, mixing energy, field gradient, and residence, with numbers that scale while the coalescing physics barely changes.
Chapter 2 / 06
How Mixing, Field, and Settling Do the Work
Mixing makes the droplets the field must grow. Dilution water injected into hot crude disperses through a mixing valve, a variable-differential restriction, or a static mixer, and the mixing energy sets the droplet size distribution: too little and the water never contacts the salt in the crude's interstitial water and solids; too much and the droplets shear so fine, and shear so much stabilizing solids and asphaltenes into their interfaces, that the field cannot coalesce them and an emulsion rides out with the oil. The mixing valve differential is the operator's primary handle, tuned with the demulsifier program against outlet salt and oil in the brine.
The electric field does the coalescing. Water droplets in oil polarize in the field's gradient; neighboring droplets, dipoles now, attract each other, collide, and coalesce, and the grown drops fall out of the oil under gravity while the field also pushes them toward the water phase by electrophoretic migration. Field strength and gradient, voltage across the grids over the spacing between them, set the coalescing force; higher gradients coalesce faster until, at excessive gradient, droplets disperse again or arc through a too-conductive emulsion. Crude conductivity is the constraint the design negotiates, which is why heavy, conductive crudes want the field architectures built for them.
Field architectures differ by power electronics. Plain AC fields, the industry's long default, alternate at line frequency and coalesce by polarization; AC/DC composite or dual-polarity systems superimpose rectified components whose gradients reach further into conductive heavy crudes, and modern high-voltage systems modulate their output to the emulsion's condition. Electrode grids are hung in two or more elevations, vertical or horizontal plate arrangements by vendor, and the transformers, oil-filled and vessel-mounted in most designs, feed them through bushings designed for the duty. Power draw is modest against the pump and heater loads around it, but the field's availability is the machine's, and the electrical design, insulation, and arc protection are the vendor's core intellectual property.
Settling and interface management finish the separation. The coalesced droplets fall through the oil phase to the interface, brine collects below, and the vessel's residence and geometry give gravity the time it needs; the interface level, held by brine draw control, must sit low enough that the field works on oil rather than water arcing and high enough that oil does not leave with the brine. Desalter internals, distribution and collection, spread the emulsion and the flows evenly so no lane short-circuits. Solids that neither rise nor fall accumulate at the interface as rag or sludge, the desalter's chronic illness, fought by solids-washing water, drain provisions, and the chemical program.
Chemistry runs alongside the physics. The crude's asphaltenes, resins, and fine solids act as natural emulsifiers, stabilizing the water-in-oil dispersion the field must break, and a demulsifier program, bottle-tested against the actual slate, is part of almost every desalter's operating reality; the wash water's chemistry matters equally, since produced or seawater high in emulsifying salts can undo the washing, and many refineries condition or blend their dilution water deliberately. pH, hardness, and oil content of the brine leaving the vessel are the water side's monitors, and the brine's oil carryover feeds the water treatment train, often an induced gas flotation unit on the wastewater side, before discharge.
Temperature is the quiet variable that licenses everything. Hot crude is less viscous, droplets move and fall more easily, and the oil's conductivity changes with temperature, so desalting improves hot; the practical window, roughly one hundred ten to one hundred fifty degrees Celsius by slate and pressure, is set by the preheat train upstream and the vessel's operating pressure, which must hold the water liquid. Too cold and the field fights viscosity; too hot, and the desalter vaporizes its water or wastes preheat better recovered in exchange against column products. The RFQ should state the temperature and pressure envelope the design must live in.
Chapter 3 / 06
Desalter Types, Stage Arrangements, and Machine Boundaries
Single-stage desalting is the base machine: one vessel, one wash, one field, taking crude to a moderate target on friendly slates with minimum water and power. Two-stage desalting adds a second vessel in series, fresh dilution water to the second stage and recycle of the first stage's water forward, doubling the salting-out driving force and halving the wash water a single stage would need for the same target; heavy, high-salt crudes and refineries feeding hydrotreaters with tight sodium limits live here. Three-stage designs exist for the hardest duties, and stage count is the first architecture decision, priced in water, power, and steel against the salt target.
Field classes separate the vendors' machines. Conventional AC grids, two elevations of hung electrodes, serve the middle of the slate range economically; composite AC/DC and dual-gradient systems reach conductive heavy crudes, their modulated gradients coalescing droplets an AC field would arc on; and combined desalter-dehydrator designs, production-duty cousins that dewater rather than desalt refinery feed, share the family. Electrode geometry, vertical plates, horizontal grids, composite arrangements, is vendor practice, and the buyer's real questions are the field's gradient range, its arc behavior on the postulated slate, and the power system's response to upset, not the brochure's name for the grid.
Duty positions name the machine's contracts. In a refinery, the desalter sits in the crude unit's preheat train, hot crude in, desalted crude out toward the fired heater and the atmospheric column, brine out to wastewater. In production, field desalters and dehydration vessels prepare crude for shipping pipelines whose salt and water limits are contractual, and the same physics runs at the wellsite scale, usually with less water discipline. Upgrading plants, those feeding delayed coker or hydrotreater trains with bitumen-derived feed, desalt to protect catalyst and coke quality, and their targets, sodium for the catalyst, solids for the coke, are the tightest. Each position changes the target and the water system, not the machine.
Adjacent machines mark the boundary. The desalter is not the heater treater, its production-scale cousin whose page this encyclopedia keeps; not the three-phase separator, knockout-drum family, or oil-water separator of the gravity separation world; and not the electrostatic precipitator, which applies the same field physics to gas-borne particulates in flue gas service, a machine with its own page. Around it in the refinery: the shell-and-tube heat exchanger network of the preheat train and the fired heater that warm the crude, the crude column it protects, the hydrotreater, fed hydrogen from a steam methane reformer, whose catalyst its sodium target defends, the delayed coker whose feed quality it shapes, and on the sour side the amine unit, whose packed towercontactors wash acid gas, and the sulfur recovery unit, with the sour-water stripper and its reboiler closing the water loop and the flare-stack handling upsets. On the water side, the brine flows to wastewater treatment, oil removal by induced gas flotation or a coalescing-filter polish, before discharge; none of these neighbors is part of the desalter purchase, but every one of them appears in its interface list.
Support systems complete the machine as installed. The wash-water system, source, conditioning, and rate control, often recycles stripped sour water or condensate by refinery water balance; the demulsifier injection package with its pumps and day tanks; the mixing valve with its differential control; the high-voltage transformers with their power supply and protection; and the instrumentation, interface level by multiple technologies since oil-water emulsions fool single instruments, pressure and temperature at the vessel, and outlet salt monitoring, commonly by conductivity of the desalted crude's aqueous extract. Utilities at remote or platform sites come from a gas engine or diesel generator power plant, which sizes the electrical scope accordingly.
Chapter 4 / 06
Key Specification Parameters
The vendor data sheet for a desalter centers on residence, field, water, and targets, and each number carries a duty consequence. The table below lists the parameters that recur across manufacturers' catalogs for single and two-stage refinery machines, with typical ranges a buyer will see. Values for a specific project come from the crude slate's assay and desalting tests and the unit's targets, and the ranges here are orientation, not a substitute for that engineering.
Parameter
Typical catalog range
What it decides
Crude throughput
tens of thousands of barrels per day
Vessel size and count; residence at rate
Residence time
roughly 10 to 30 min
Settling time; coalescence completion
Operating temperature
roughly 110 to 150 C
Viscosity, conductivity, water holdup
Dilution water rate
3 to 10 vol percent per stage
Wash driving force; water system load
Field voltage
high tens of kV class
Gradient; coalescing force; arc margin
Field gradient
vendor class, kV per unit spacing
Coalescing rate on the slate's conductivity
Outlet salt target
1 to 5 PTB typical
Stage count; downstream corrosion budget
Outlet BS&W
0.1 to 0.5 percent class
Water carryover; column corrosion
Brine oil content
tens to hundreds of ppm
Wastewater load; oil loss
Transformer power
tens to hundreds of kW per grid
Field availability; operating cost
Three of these numbers deserve the buyer's suspicion when they arrive without a basis. Outlet salt quoted without the slate, its inlet salt and solids, and the wash-water rate assumed is a number from someone else's crude. Residence quoted as total vessel volume ignores the working oil volume the interface level actually leaves. Field performance quoted at a light crude's conductivity flatters every heavy slate the refinery will run. An RFQ that demands desalting test data on the actual slate, or reference units on it, separates engineered offers from assembled ones.
Materials and construction follow the service. Vessels are carbon steel with corrosion allowances for the brine zone and often clad or lined wetted surfaces; electrodes are steel with insulator assemblies in high-dielectric materials; bushings and transformers are oil-filled electrical equipment rated for the area classification; internals, distribution and collection, are simple steel in the main; and the mixing valve is an engineered variable-differential device. Interface measurement, usually multiple technologies agreed in failure, level controls, and the salt monitor complete the instrumented machine. Every wetted and energized interface has a maintenance expectation, and the insulators' cleanliness is the electrical system's life.
Chapter 5 / 06
Selection Decision Factors and RFQ Language
Selection starts with the slate, not the catalog. The crude assay, salt as chlorides, water, solids, conductivity, and emulsion tendency, from the actual blends the refinery will run, decides everything: heavy conductive crudes want composite fields and two stages, solids-heavy slates want wash discipline and drainage, waxy or asphaltenic slates want the demulsifier program tested before the vessel is sized. Desalting tests on the real slate, bottle tests at least, pilot or vendor-facility runs for the hardest cases, are the honest basis of any guarantee, and a vendor who will not run them should not be trusted with one.
The water system decision frames the operating reality. Dilution water source and quality, stripped sour water, condensate, seawater at coastal sites, or produced water recycled, set the wash's salt content and emulsifier load, and refineries condition or blend deliberately; wash rate per stage, with recycle between stages in multi-stage trains, sets both the salt target's reach and the wastewater load, whose oil content feeds the treatment train. The demulsifier program is selected with the water system, bottle-tested against the slate and the season, and budgeted as an operating cost of the machine rather than an afterthought.
The table below organizes the decision into the factors that recur across projects, with the questions the buyer should be able to answer before the RFQ goes out. Each row is a place where an incomplete answer becomes an underspecified vessel and a corrosion argument later.
RFQ language for a desalter should name the slate and the target. A workable specification states: the crude slate with assays, design and maximum throughput, inlet salt, water, and solids ranges; the outlet salt and BS&W targets with the downstream basis, overhead corrosion or catalyst sodium; stage count intent with vendor free to propose; dilution water source, quality, and rate scheme including recycle; thermal envelope, preheat temperature and operating pressure; field architecture with gradient range and arc behavior on the stated slate, plus transformer and protection scope; mixing system with differential range and control; interface level measurement and brine draw control philosophy; demulsifier injection scope and the bottle-test basis expected; brine oil-content expectation and the wastewater interface; and the acceptance basis, performance test on the actual slate at rate against the salt target with water and power consumption witnessed. Naming the interface equipment, preheat exchangers and fired heater upstream, crude column downstream, and the brine treatment train, lets vendors bid the connections correctly.
Chapter 6 / 06
Installation, Standards, Failure Modes, and Maintenance
Installation is vessel, electrical, and interface work. The vessel sets on its foundation into the preheat piping, electrodes and insulators install with the cleanliness the field demands, transformers mount and cable, and the water, chemical, and mixing systems tie in. Commissioning brings the vessel to pressure and temperature with water first, proving level controls and brine draw, then energizes the field in steps on crude, tuning the mixing valve differential and the demulsifier rate against outlet salt. The performance test, the slate at rate against the salt target, is the acceptance event, and its water and power consumption should be witnessed because they are the operating numbers the plant will live with.
Standards for desalters are vessel and electrical practice rather than a single machine standard. The vessel follows the pressure equipment code of the jurisdiction with petroleum service practice; the electrical system, transformers, bushings, and area classification, follows electrical apparatus standards for the location; and water discharge follows the site's permit. There is no single international desalter standard governing the machine end to end, so the RFQ must name the applicable pressure, electrical, and discharge codes and the vendor's own manufacturing standards for electrode assembly, insulation qualification, and transformer rating. Edition references should be verified current at purchase rather than copied from an old specification.
The recurring failure modes are interface and electrical patterns with honest symptoms. Rag layer and sludge accumulation at the interface, fed by solids and emulsion upsets, shows as oil in brine, salt misses, and level indication disagreement, and is fought with wash discipline, drainage, and chemicals; insulator fouling and tracking degrade the field and show as power draw drift and eventual trips, caught by electrical trending and inspection at outages; mixing valve wear shifts droplet size and the emulsion character; and transformer or bushing faults, rare but unit-stopping, are the electrical system's catastrophic path. Upstream upsets, a slate change or a tank bottom drawn hard, arrive as operating problems here, which is why the operating program, water, chemicals, and mixing, belongs to the unit's trained staff.
Maintenance planning is interval driven and outage leveraged. The table below lists the recurring items with the typical cadence a plant will schedule, assembled from common practice; the real schedule follows the slate's behavior and the salt trend the lab actually runs.
Item
Typical action
Typical cadence
Salt and BS&W monitoring
Outlet salt trend, brine oil and pH checks
Daily to per-shift
Water and chemical program
Verify wash rate, demulsifier dose, bottle retest on slate change
Weekly checks, seasonal retest
Mixing valve
Inspect trim wear, verify differential control
Quarterly
Interface and rag
Level cross-check, drain rag and solids, inspect internals
Monthly checks, outage cleaning
Electrical system
Trend transformer power, inspect insulators and bushings
Long-term care keeps the target honest as the slate drifts. Refineries change crude slates for economics, and the desalter tuned for one slate slowly mistunes on another; periodic bottle testing, water and chemical re-optimization, and electrical trending recover the margin before the overhead corrosion data announces it. Grid and transformer upgrades extend existing vessels to harder slates, and wash-water system improvements pay back in target and wastewater together. The plant that treats the desalter as the crude unit's corrosion insurance, tested every slate change and cleaned every outage, is the plant whose overhead lines outlast the economists' slate of the quarter.
FAQ
Why do refineries desalt crude oil?
Because salt destroys the crude unit from the inside. Crude arrives with salt in residual water and solids; in the crude column's hot overhead, the chlorides hydrolyze to hydrochloric acid that corrodes the overhead system, and the salts and solids also foul exchangers and load column bottoms. The desalter washes the salt into dilution water and removes it as brine before the heater, cutting salt from tens of pounds per thousand barrels to single digits and converting an uncontrolled corrosion driver into a managed one. It is the cheapest corrosion protection a refinery owns.
How does an electrostatic desalter work?
In three steps: mix, coalesce, settle. Dilution water injected into the hot crude is dispersed into fine droplets by a mixing valve, and the water contacts and dilutes the salt in the crude's interstitial brine and solids. The emulsion then passes between high-voltage electrode grids, where the field's gradient polarizes the water droplets, makes them attract and collide, and grows them until gravity settles them through the oil-water interface as brine. Desalted crude leaves the top; brine leaves the bottom to water treatment; and the electric field is what makes this fast enough to fit in one vessel.
What is the difference between single-stage and two-stage desalting?
A single-stage desalter washes once, one dilution-water injection and one field, reaching moderate salt targets on friendly crudes with the minimum of water and power. A two-stage train washes twice in series, fresh water to the second stage and the first stage's water recycled forward, roughly halving the wash water needed for the same target and reaching the low single-digit pounds per thousand barrels that hydrotreater catalyst and tight overhead budgets demand. Heavy, high-salt crates justify the second vessel; light sweet ones often do not, which is why both arrangements ship.
What dilution water should a desalter use?
Water that washes without emulsifying. The ideal is low-salt, low-hardness, clean water, and refineries use what their balance offers: stripped sour water and process condensate are common and cheap, seawater serves coastal sites within its salt and solids discipline, and produced water can recycle where its oil and emulsifier content are managed. What matters is the water's contribution to the wash, its salt and stabilizing solids, against the slate's emulsion tendency, and many plants condition or blend deliberately. The water system is as much a design decision as the vessel.
What limits desalter performance on heavy crude?
Physics stacks against heavy slate. Heavy crude is viscous, so droplets move and settle slowly; it is conductive, so the electric field's gradient is harder to hold without arcing; and its asphaltenes and fine solids are natural emulsifiers that stabilize the water-in-oil dispersion the field must break. The countermeasures are composite AC/DC fields built for conductive crudes, higher temperature within the pressure envelope, more wash water with multi-stage arrangement, and a demulsifier program bottle-tested on the actual slate. The honest sizing basis for any of them is desalting test data, not analogy.
What is a desalter rag layer and why does it matter?
The rag layer is the accumulated band of emulsion and solids that gathers at the oil-water interface, neither rising with the oil nor settling with the brine. Fed by fine solids, asphaltenes, and upsets in water or chemicals, it steals vessel residence, blinds interface instruments, and eventually carries over into brine or oil as salt and water misses. Plants fight it with wash discipline, demulsifier tuning, routine drainage of interface material, and solids management at the tank farm upstream, and inspect and clean it at outages; a thick rag layer is the visible symptom of a mistuned program.
What should an electrostatic desalter RFQ include?
State the crude slate with assays, design and peak throughput, and inlet salt, water, and solids ranges; the outlet salt and BS&W targets with their downstream basis; stage intent with vendor free to propose; dilution water source, quality, and rate scheme including recycle; the thermal envelope of preheat temperature and operating pressure; field architecture with gradient range and arc behavior on the stated slate, transformer and protection scope; the mixing system and its differential control; interface measurement and brine draw philosophy; demulsifier injection and bottle-test basis; brine oil-content expectations and the wastewater interface; and the acceptance basis, a performance test on the actual slate at rate against the salt target with water and power consumption witnessed. Naming the preheat train and crude column upstream and downstream, and the brine treatment train, lets vendors bid the connections correctly.